Samsung Television SyncMaster 400PXn User Manual

							   Adjusts the audio volume. 
4) ENTER
  Activates a highlighted menu item. 
5) SOURCE 
 
Switches from PC mode to Video mode.  
Changing the source is only allowed for external devices that are connected to the LCD Display at the time. 
[PC] 
→
 [BNC]  →
 [DVI]  →
 [AV]  →
 [S-Video]  →
 [Component]  
>> Click here to see an animation clip. 
6) PIP
  Push the PIP button to turn the PIP screen On / Off. 
More than one PIP cannot overlap on screen as BNC and the component use the same terminal.  
>> Click here to see an animation clip. 
•
PC
  AV / S-Video / Component Mode
•
BNC
  AV / S-Video Mode
•
DVI
  AV / S-Video / Component Mode
•
AV / S-Video 
  PC / BNC / DVI Mode
•
Component
  PC / DVI Mode
7)  Power button 
  Turns the LCD Display On/Off.
8) Power indicator
  Shows PowerSaver mode by blinking green.
9) Remote Control Sensor 
  Aim the remote control towards this spot on the LCD Display. 
Note
•See  PowerSaver  described in the manual for further information regarding power saving functions. For 
energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for 
long periods.
 
 
 
Rear
 
Note
• For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD  Display s configuration at the back may vary slightly depending on the LCD Display model.
 
  
						

							 
1) POWER S/W ON [ | ] / OFF [O]
  Switches the LCD Display On/Off.
2) POWER IN 
 The power cord plugs into the LCD Display and 
the wall plug.
 
3) RS232C OUT/IN (RS232C Serial PORT)
 
MDC(Multiple Display Control) Program Port 
4) DVI / PC IN [DVI(HDCP)] (PC Video  Connection Terminal)
 
Using a DVI Cable (DVI-D to DVI-D) - DVI 
mode (Digital PC)
5) DVI / PC IN [RGB] (PC Video  Connection Terminal)
 
Using a D-Sub Cable (15 pin D-Sub) - PC 
mode (Analog PC)
6) DVI / PC IN [PC/DVI/BNC AUDIO IN]  (PC/DVI/BNC Audio Connection 
Terminal (Input))
 
7) COMPONENT AUDIO IN [L-AUDIO-R] (Component Audio Connection Terminal 
(Input))
8) BNC/COMPONENT OUT [R/P
R, G/Y, B/PB, 
H, V] (BNC/Component Connection 
Terminal (Output)) 
  BNC (Analog PC) Connection: connecting the R, 
G, B, H, V ports  
Component Connection: connecting the PR, Y, 
P
B ports
9) BNC/COMPONENT IN [R/PR, G/Y, B/PB, H, 
V] (BNC/Component Connection Terminal 
(Input))
 
10) AV AUDIO IN [L-AUDIO-R] (LCD Display   
						

							Audio Connection Terminal (Input)) 
11) AV OUT [VIDEO] (VIDEO Connection  Terminal): AV mode (Output)
12) AV IN [VIDEO] (VIDEO Connection  Terminal) (Input) 
13) AV OUT [S-VIDEO] (S-VIDEO Connection  Terminal): S-VIDEO mode (Output)
14) AV IN [S-VIDEO] (S-VIDEO Connection  Terminal) (Input)
15) EXT SPEAKER(8  Ω)[- - L - +, - - R - +] (EXT 
Speaker Connection Terminal)
16) AUDIO OUT [L-AUDIO-R] (LCD Display  Audio Connection Terminal (Output))
  AUDIO OUT is the terminal for sound output of 
PC, DVI or BNC.
 
Note
• The number of LCD Display s that can be connected to loopout may differ depending on the cables, signal  source etc. With cables where there is no degradation or signal source, up to ten LCD Displays can be 
connected.
 
17) Kensington Lock 
  The Kensington lock is a device used to 
physically fix the system to something when 
using it in a public place. (The locking device has 
to be purchased separately.) 
For using a locking device, contact the place 
of purchase.
 
Note
•See  Connecting the LCD Display  for further information regarding cable connections.
 
 
Remote Control
 
Note
• The performance of the remote control may be affected by a TV or other electronic device operating near  the LCD Display , causing a malfunction due to interference with the frequency.
 
 
1. ON / OFF
2. MAGICNET 
3. MDC  
4. LOCK  
5. MagicNet buttons
6.+100 -/-- 
7. VOL 
8. MUTE 
9. TTX/MIX 10. MENU11. ENTER 
12. P.MODE13. AUTO 
14. PRE-CH 
15 .  CH/P 16. SOURCE 17. INFO 
18. EXIT 19. Up-Down Left-Right buttons
20. S.MODE 
21. STILL 
22. FM RADIO 
23. P.SIZE  
						

							24. SRS25. DUAL/MTS 26. PIP27. SOURCE 28. SWAP
29.  SIZE
30. REW31. STOP 32. PLAY/PAUSE 33. FF 
 
 
1) ON / OFF
  Turns the LCD Display On/Off.
2) MAGICNET
  MagicNet Quick Launch Button. 
- This fuction does not work for this monitor. 
3) MDC 
  MDC Quick Launch Button. 
4) LOCK 
 Activates or deactivates all function keys on both the remote control and the LCD Display except for the 
Power and LOCK buttons.
5) MagicNet buttons
 Used for MagicNet. 
- This fuction does not work for this monitor. • Alphanumeric: Used to enter the Internet address.
• DEL: Functions as the backspace. 
• SYMBOL: Used to enter the symbols. (.O_-) 
• ENTER: Used to enter values.
6) +100 -/-- 
 
Press to select channels over 100.  
For example, to select channel 121, press +100, then press 2 and 1.  
- This fuction does not work for this monitor. 
7) VOL
  Adjusts the audio volume.
8)
 MUTE
 Pauses (mutes) the audio output temporarily. 
This is displayed on the lower left corner of the screen. 
The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 
9)
 TTX/MIX  
						

							 TV channels provide text information services via teletext. 
- This fuction does not work for this monitor. 
10)
 MENU 
  Opens the on-screen menu and exits from the menu screen or closes the screen adjustment menu.
11)  ENTER 
  Activates a highlighted menu item.
12) P.MODE 
 When you press this button, current picture mode is displayed on the lower center of the screen.  
 
AV / S-Video / Component : P.MODE 
 
The Monitor has four automatic picture settings that are preset at the factory.  
Then push button again to circle through available preconfigured modes.  
( Dynamic  →
 Standard  →
 Movie  →
 Custom )  
 
PC/DVI/BNC : M/B (MagicBright)   
MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of 
the image you are watching.  
Then push button again to circle through available preconfigured modes.  
(Entertain  →
 Internet  →
 Text  →
 Custom ) 
13) AUTO
  Adjusts the screen display automatically in PC mode.  
By changing the resolution in the control panel, auto function is performed.
14)
 PRE-CH
 Returns to the immediately previous channel. 
- This fuction does not work for this monitor. 
15)
 CH/P 
 In TV mode, selects TV channels.  
- This fuction does not work for this monitor. 
16)
 SOURCE 
  Changes the video source. 
17) INFO 
  The current picture information is displayed in the top left corner of the screen.
18)  EXIT 
  Exits from the menu screen.
19) Up-Down Left-Right buttons 
  Moves from one menu item to another horizontally, vertically or adjusts selected menu values.
20)
 S.MODE
 When pressing this button, the current mode is displayed at the bottom centre of the screen.  
The LCD Display has a built-in high fidelity stereo amplifier.  
Then press the button again to circle through available preconfigured modes.  
( Standard 
→
 Music  →
 Movie  →
 Speech  →
 Custom ) 
21) STILL
  Press the button once to freeze the screen. Press it again to unfreeze. 
22) FM RADIO 
  Turns the FM Radio on/off.  
In PC/DVI mode, sets the SOUND to FM Radio.  
In general Video mode, selects FM Radio, and turns off the screen.  
In areas where the signal is weak, noise may occur during FM radio broadcasts.  
- This fuction does not work for this monitor. 
23) P.SIZE 
  Press to change the screen size. 
24)
 SRS
 SRS
25) DUAL/MTS 
DUAL- 
						

							  
- This fuction does not work for this monitor. STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated 
depending on the broadcasting type by using the DUAL button on the remote control while watching TV.
MTS-
You can select MTS (Multichannel Television Stereo) mode. 
 Audio TypeMTS/S_ModeDefault
FM Stereo
MonoMonoManual ChangeStereoMono 
↔
 Stereo
SAPMono  ↔
 SAPMono
26)  
PIP  
  Every time you press the button, a PIP screen appears.
27)  
SOURCE
  Changes the source of the PIP window signal.
28) SWAP
  Swaps the contents of the PIP and main image. 
The image in the PIP window will appear on the main screen, and the main screen image will appear in the 
PIP window.
29)
 
SIZE
  Switches the PIP Picture Size.
30)  REW
 Rewind
31)
 STOP 
 Stop
32)  PLAY / PAUSE 
 Play/Pause
33)  FF 
 Fast forward
© 1995~2007 SAMSUNG. ALL Right Reserved  
						

							 Mechanical Lay-out
 | Monitor Head  | Stand  | Speaker  | Installation VESA Bracket  | Wall Bracket Installation  
1. Mechanical Lay-out
2. Monitor Head
Dodatak 


						

							3. Stand
4. Speaker
5. Installation VESA Bracket 
zWhen installing VESA, make sure to comply with the international VESA standards.  zPurchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place 
an order. After your order is placed, installation  professionals will visit you and install the bracket.  
zAt least 2 persons are needed in order to move the LCD Monitor.  zSamsung is not responsible for any product damage or any injury caused by installation at customers discretion.  
Dimensions 
						

							For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
6. Wall Bracket Installation 
zContact a technician for installing the wall bracket.  zSamsung Electronics is not responsible for any damages to the product or harm to customers when the 
installation is done by the customer.  
zThis product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. 
 
Components
Only use the components and accessories shipped with the product.
` 
Wall Bracket  (1) Hinge 
(Left 1, Right 1) Plastic Hanger
(4) Screw(
A)
(11) Screw(
B)
(4) Anchor 
(11)
 
Wall Bracket Assembly
 
Insert and tighten the Captive Screw in the 
direction of the arrow.  
When done, mount the wall bracket on the wall.  
 
A. Captive Screw  
B. Wall Bracket  
C. Hinge (Left) 
D. Hinge (Right) 
						

							There are two hinges(left and right). Use the correct one.
Before drilling into the wall, check if the length 
between the two locking holes at the back of the 
product is correct. 
If the length is too short or long, loosen all or 
some of the 4screws on the wall bracket to adjust 
the length. 
 
A. Length between the two locking holes
Check the installation diagram and mark the drill 
points on the wall. Use the 5.0 mm bit to drill 
holes deeper than 35 mm. Fix each anchor in the 
corresponding hole. 
Match each of the brackets and hinge holes to 
the corresponding anchor holes and insert and 
tighten the 11 screws A.
 
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the 
screw are the same)