Samsung SCX 4824FN User Manual

							Introduction_21
SUPPLIED SOFTWARE
After you have set up your machine and  connected it to your computer, you 
must install the printer software. If  you are a Windows or Macintosh OS, 
install the software from the supplied CD and if you are a Linux OS user, 
download the software from the  Samsung website (www.samsung.com/
printer) and install.
PRINTER DRIVER FEATURES
Your printer drivers support the following standard features:
• Paper orientation, size, source and media type selection
• Number of copies
In addition, you can use various spec ial printing features. The following 
table shows a general overview of f eatures supported by your printer 
drivers:
Printer driver 
PostScript driver (SCX-4x28 Series only)
OSCONTENTS
Windows•Printer driver: Use this driver to take full advantage of 
your printer’s features.
•
Postscript Printer Description (PPD) file: Use the 
PostScript driver to print documents with complex fonts 
and graphics in the PS language. (
SCX-4x28 Series 
only)
•
Scanner driver: TWAIN and Windows Image 
Acquisition (WIA) drivers  are available for scanning 
documents on your machine.
•
Smart Panel: This program allows you to monitor the 
machine’s status and alerts you when an error occurs 
during printing.
•
SmarThru Officea: This is the accompanying 
Windows-based software for your multifunctional 
machine. 
•SetIP: Use this program to set your machine’s TCP/IP 
addresses.
a. Allows you to edit a scanned image in many ways using a powerful image  editor and to send the image by emai l. You can also open another image 
editor program, like Adobe Photoshop, from SmarThru. For details, refer to 
the onscreen help supplied on the SmarThru program.
Linux• Printer driver : Use this driver to take full advantage 
of your printer’s features.
• Postscript Printer Description (PPD) file : Use this 
file to run your machine from a Linux computer and 
print documents. 
(SCX-4x28 Series only)
• SANE : Use this driver to scan documents.
•SetIP: Use this program to set your machine’s TCP/IP 
addresses.
Macintosh• Printer driver : Use this driver to take full advantage 
of your printer’s features.
• Postscript Printer Description (PPD) file : Use this 
file to run your machine from a Macintosh computer 
and print documents. 
(SCX-4x28 Series only)
• Scanner driver: TWAIN driver is available for 
scanning documents on your machine.
•
SetIP: Use this program to set your machine’s TCP/IP 
addresses.
Some models or operating system may not support the certain 
feature(s) in the following table.
FEATUREWINDOWSLINUXMACINTOSH
Machine quality option OO O
Poster printingOX X
Multiple pages per sheet 
(N-up)OO (2, 4) O
Fit to page printing
OX O
Scale printingOX O
Different source for first 
pageOX O
Watermark
OX X
OverlayOX X
DuplexOX O
FEATUREWINDOWSLINUXMACINTOSH
Machine quality option OO O
Poster printing XX X
Multiple pages per sheet 
(N-up)O O (2, 4) O
Fit to page printing
OX O
Scale printingOX O
Different source for first 
page XX O
Watermark
XX X
OverlayXX X
DuplexOX O
Downloaded From ManualsPrinter.com Manuals 
						

							22 _Getting started
getting started
This chapter gives you step-by-step in structions for setting up the machine.
This chapter includes:
• Setting up the hardware
• System requirements
• Setting up the network • Installing the software
• Machines basic settings
SETTING UP THE HARDWARE
This section shows the steps to set up the hardware which is explained in 
the 
Quick Install Guide . Make sure you read  Quick Install Guide and 
complete following steps.
1. Select a stable location. 
Select a level, stable place with adeq uate space for air circulation. Allow 
extra space to open covers and trays. 
The area should be well-ventilated and  away from direct sunlight or 
sources of heat, cold, and humidity. Do  not set the machine close to the 
edge of your desk or table.
 
Printing is suitable for altitudes under 1,000 m (3,281 ft). Refer to the 
altitude setting to optimize your  printing. See Altitude adjustment on 
page 26 for more information.
Place the machine on a flat, stable su rface so that there is no incline 
greater than 2 mm (0.08 inch). Otherwise, printing quality may be 
affected.  2.
Unpack the machine and check all the enclosed items.
3. Remove the tape holding the machine tightly.
4. Install the toner cartridge.
5. Load paper. (See Loading paper on page 34.)
6. Make sure that all the cables  are connected to the machine. 
7. Turn the machine on. 
When you move the machine, do not tilt or turn it upside down. 
Otherwise, the inside of the mach ine may be contaminated by toner, 
which can cause damage to the machine or bad print quality.
This equipment will be inoperable when mains power fails. 
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_23
SYSTEM REQUIREMENTS
Before you begi n, ensure that your  system meets the following 
requirements:
Windows
Your machine supports the fo llowing Windows operating systems.
Macintosh
Linu
x
OPERATING 
SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAMFREE HDD SPACE
Windows 
2000 Pentium II 400 MHz 
(Pentium III 933 MHz)
64 MB 
(128 MB)600 MB
Windows XP
Pentium III 933 MHz 
(Pentium IV 1 GHz) 128 MB 
(256 MB)1,5 GB
Windows 
Server 2003 Pentium III 933 MHz 
(Pentium IV 1 GHz)
128 MB 
(512 MB)1.25 GB to 
2 GB
Windows 
Server 2008 Pentium IV 1 GHz
(Pentium IV 2 GHz) 512 MB 
(2048 MB)
10 GB
Windows 
Vista Pentium IV 3 GHz 512 MB 
(1024 MB)15 GB
Windows 7
Pentium IV 1 GHz 32-bit 
or 64-bit processor or 
higher 1 GB 
(2 GB)
16 GB
• Support for DirectX 9 graphics with 128 MB  memory(to enable the Aero theme).
• DVD-R/W Drive
Windows 
Server 2008 
R2 Pentium IV 1 GHz(x86) or 
1.4GHz(x64) 
processors(2GHz or 
faster) 512 MB 
(2048 MB)
10 GB
• Internet Explorer 5.0 or higher 
is the minimum requirement for all 
Windows operating systems.
• Users who have an administrator right can install the software.
OPERATING  SYSTEM
REQUIREMENT (RECOMMENDED)
CPURAM
FREE HDD 
SPACE
Mac OS X 
10.3 ~ 10.4 • Intel Processor
• Power PC G4 /
G5 • 128 MB for a 
Power-PC based 
Mac (512 MB).
• 512 MB for an  Intel-based Mac (1 
GB) 1 GB
Mac OS X 10.5
• Intel Processor
• 867 MHz or 
faster Power 
PC G4 /G5 512 MB (1 GB) 1 GB
Mac OS X 10.6
• Intel Processor 1 GB (2 GB) 1 GB
ITEMREQUIREMENTS
Operating system RedHat 8.0, 9.0 (32bit)
RedHat Enterprise Linux WS 4, 5 (32/64bit)
Fedora Core 1~7 (32/64bit)
Mandrake 9.2 (32bit), 10.0, 10.1 (32/64bit)
Mandriva 2005, 2006, 2007 (32/64bit)
SuSE Linux 8.2, 9.0, 9.1 (32bit)
SuSE Linux 9.2, 9.3, 10 .0, 10.1, 10.2 (32/64bit)
SuSE Linux Enterprise Desktop 9, 10 (32/64bit)
Ubuntu 6.06, 6.10, 7.04 (32/64bit)
Debian 3.1, 4.0 (32/64bit)
CPU Pentium IV 2.4GHz (IntelCore2)
RAM512 MB (1024 MB)
Free HDD space1 GB (2GB)
• It is necessary to claim swap partition of 300 MB or larger for 
working with large scanned images.
• The Linux scanner driver suppor ts the optical resolution at 
maximum.
• Please visit www.samsung.com for open source information.
Downloaded From ManualsPrinter.com Manuals 
						

							24 _Getting started
SETTING UP THE NETWORK
You need to set up the network protocols on the machine to use it as your 
network printer. You can set up the  basic network settings through the 
machines control panel.
Supported operating systems
The following table shows the networ k environments supported by the 
machine:
Configuring network prot ocol via the machine
You can set up TCP/IP network paramet ers, follow the steps listed below. 
1. Make sure your machine is connected to the network with an RJ-45 
Ethernet cable.
2. Make sure you have tu rned on the machine.
3. Press  Menu on the control panel, until you see  Network on the bottom 
line of the display. 
4. Press  OK to access the menu.
5. Press the left/right arrow until  TCP/IP displays. 
6. Press  OK.
7. Press the left/right arrow until  Static displays.
8. Press  OK.
9. Press the left/right arrow until  IP Address displays.
10. Press  OK.
Enter a byte between 0 and 255 using the number keypad and press the 
left/right arrow  to move between bytes.
Repeat this to complete the address fr om the 1st byte to the 4th byte.
11. When you have finished, press  OK.
Repeat steps 9 and 10 to configur e the other TCP/IP parameters: 
subnet mask and gateway address.
ITEMREQUIREMENTS
Network interface • Ethernet 10/100 Base-TX
Network operating system • Windows 2000/XP/2003/2008/Vista/7/
Server 2008 R2
• Various Linux OS
• Mac OS 10.3 ~ 10.6
Network protocols •TCP/IP
• Standard TCP/IP
•LPR
• IPP/HTTP
• Bonjour
• DHCP
•BOOTP
If you want to set up DHCP network protocol, go to  http://developer.apple.com/networking/bonjour/download/, select the 
Bonjour program that is appropri ate for your computer operating 
system and install the pr ogram. This program will allow you to set 
network parameters automatically. Fo llow the instructions in the 
installation window. This program does not support Linux.
Contact the network administrator if  you are not sure how to configure.
You can also set up the network settings through the network 
administration programs. 
•
SyncThru™ Web Admin Service: Web-based printer 
management solution for network administrators. SyncThru™ 
Web Admin Service
 provides you with an efficient way of 
managing network devices and lets you remotely monitor and 
troubleshoot network machines from any site with corporate 
internet access. Download this program from  http://
solution.samsungprinter.com.
•SyncThru™ Web Service: Web server embedded on your 
network print server, which allows you to:
- Configure the network parameters  necessary for the machine to 
connect to various network environments.
- Customize machine settings.
•
SetIP: Utility program allowing you to select a network interface 
and manually configure the IP a ddresses for use with the TCP/IP 
protocol. See Using SetIP program on page 25.
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_25
Using SetIP program
This program is for the network IP setting using the MAC address which is 
the hardware serial number of the net work printer card or interface. 
Especially, it is for the network adminis trator to set several network IPs at 
the same time. 
Installing the program
1. Insert the driver CD provided along wit h your machine. When the driver 
CD runs automatically , close the window.
2. Start  Windows Explorer  and open the X drive. (X represents your CD-
ROM drive.)
3. Double click  Application > SetIP.
4. Open the folder of the language you plan to use.
5. Double click  Setup.exe to install this program. 
6. Follow the instruction on the window to complete the installation.
Starting the program
1.Print the machines network information report which includes your 
machine’s MAC address. See Printing reports on page 57.
2. From the Windows  Start menu, select  All Programs > Samsung 
Network Printer Utilities  > SetIP  > SetIP.
3. Click   in the SetIP window to open the TCP/IP configuration window. 
4. Enter the network cards MAC address, IP address, subnet mask, 
default gateway, and then click  Apply.
5. Click  OK, then the machine prints the network information. Confirm all 
the settings are correct.
6. Click  Exit to close the  SetIP program.
INSTALLING THE SOFTWARE
You have to install the machine softwar e for printing. The software includes 
drivers, applications, and ot her user friendly programs. 
1. Make sure that the network setup for your machine is completed. (See 
Setting up the network on page 24.)  All applications should be closed 
on your computer before beginning installation.
2. Insert the Printer Software CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation window 
appears. 
If the installation window does not appear, click  Start > Run. Type 
X:\ Setup.exe , replacing “X” with the letter  which represents your drive 
and click  OK.
If you use Windows vista, Windows 7 and Windows Server 2008 R2, 
click  Start > All Programs  > Accessories  > Run, and type 
X:\ Setup.exe .
If the  AutoPlay  window appears in Windows vista, Windows 7 and 
Windows Server 2008 R2, click  Run Setup.exe  in Install or run 
program  field, and click  Continue in the User Account Control  
window.
3. Click  Next.
• If necessary, select a language from the drop-down list.
• You can only use SetIP program when your machine is connected  to a network.
• The following procedure is based on the Windows XP operating 
system. 
• If you are in a non-static IP  address environment and need to 
setup a DHCP network protocol, go to the  http://
developer.apple.com/networking/bonjour/download/, select the 
program Bonjour for Windows due to your computer operating 
system, and install the program. This program will allow you to fix 
the network parameter automatically . Follow the instruction in the 
installation window. This program does not support Linux.
When you enter the MAC addre ss, enter it without colon(:).
• The following procedure is for when the machine is being used as 
a network machine. If you want to connect a machine with a USB 
cable, refer to  Software section .
• The following procedure is based on the Windows XP operating 
system. The procedure and popup window which appear during 
the installation may differ depending on the operating system, the 
printer feature, or the interface in use.
Downloaded From ManualsPrinter.com Manuals 
						

							26 _Getting started
4.Select  Typical installation for a network printer , and then click Next. 
5.The list of machines available on the network appears. Select the printer 
you want to install from the list and then click  Next.
 
• If you do not see your machine on the list, click  Update to refresh the 
list, or select  Add TCP/IP Port  to add your machine to the network. 
To add the machine to the network , enter the port name and the IP 
address for the machine.
To verify your machine’s IP ad dress or the MAC address, print a 
Network Configuration page. (See Printing reports on page 57.)
• To find a shared network printer (UNC Path), select  Shared Printer 
[UNC]  and enter the shared name manually or find a shared printer 
by clicking the  Browse button.
6. After the installation is finished, a window appears asking you to print a 
test page and to register yourself as  a user of Samsung machines in 
order to receive information from Samsung. If you desire, select the 
corresponding checkbox(es) and click  Finish.
MACHINES BASIC SETTINGS
After installation is complete, you ma y want to set the machines default 
settings. Refer to the next section if you would like to set or change values.
Altitude adjustment
The print quality is affected by atmo spheric pressure, which is determined 
by the height of the machine above sea level. The following information will 
guide you on how to set your machine to the best print quality or best quality 
of print.
Before you set the altitude value, find the altitude where you are using the 
machine.
1. Ensure that you have installed the pr inter driver with the provided     
Printer Software CD.
2. Double-click the  Smart Panel icon on the Windows task bar (or 
Notification Area in Linux). 
You can also click  Smart Panel on the status bar in Mac OS X.
3. Click  Printer Setting .
4. Click  Setting >  Altitude Adjustment . Select the appropriate value from 
the dropdown list, and then click  Apply. 
Changing the display language
To change the language that appears on the control panel, follow these 
steps:
1.Press  Menu until System Setup  appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Language appears and press  OK.
4. Press the left/right arrow until th e language you want appears and press 
OK .
5. Press  Stop/Clear  to return to ready mode.   
If you are not sure of the IP  address, contact your network 
administrator or print network information. (See Printing 
reports on page 57.)
• If your machine does not work properly after the installation, try  to reinstall the printer driver. See  Software section.
• During the printer driver installa tion process, the driver installer 
detects the location informati on for your operating system and 
sets the default paper size for your machine. If you use a 
different Windows location, you must change the paper size to 
match the paper you usually use. Go to printer properties to 
change the paper size after installation is complete. 
1 Normal
2High 1
3High 2
4High 3 
If your machine is connected to a network,  SyncThru Web 
Service  screen appears automatically. Click  Machine Settings > 
Setup  (or Machine Setup ) > Altitude adj. . Select the appropriate 
altitude value, and then click Apply .
0
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_27
Setting the date and time 
The current date and time are shown on the display when your machine is 
on and ready to work. All of your faxes will have the date and time printed on 
them.
1.Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Date & Time appears and press  OK.
4. Enter the correct time and date using the number keypad. 
Month  = 01 to 12
Day     = 01 to 31
Year    = requires four digits
Hour    = 01 to 12 (12-hour mode) 
              
 00 to 23 (24-hour mode)
Minute = 00 to 59
   
You can also use the left/right arrow to move the cursor under the 
digit you want to correct and enter a new number.
5. To select  AM or PM  for 12-hour format, press the 
*or # button or any 
number button.
When the cursor is not under the  AM or PM indicator, pressing the 
*or # 
button immediately moves the cursor to the indicator.
You can change the clock mode to 24-hour format (e.g. 01:00 PM as 
13:00). For details, see the next section.
6. Press  OK to save the time and date. 
When you enter a wrong number,  Out of Range appears and the 
machine does not proceed to the ne xt step. If this happens, simply 
reenter the correct number.
7. Press  Stop/Clear to return to ready mode.
Changing the clock mode
You can set your machine to display the current time using either a 12-hour 
or 24-hour format.
1.Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Clock Mode appears and press  OK. 
4. Press the left/right arrow  to select the other mode and press  OK.
5. Press 
Stop/Clear to return to ready mode.
Changing the default mode 
Your machine is preset to Fax m ode. You can switch this default mode 
between Fax mode and Copy mode.
1. Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Default Mode appears and press  OK.
4. Press the left/right arrow until the  default mode you want appears and 
press  OK.
5. Press  Stop/Clear to return to ready mode.
Setting sounds
You can control the following sounds:
• Key Sound: Turns the key sound on or off. With this option set to  On
, a 
tone sounds each time a key is pressed. 
• Alarm Sound: Turns the alarm sound on or off. With this option set to 
On
, an alarm tone sounds when an error occurs or fax communication 
ends.
• Speaker: Turns on or off the sounds from the telephone line through 
the speaker, such as a dial tone or a fax tone. With this option set to 
Comm.  which means “Common,” the speaker is on until the remote 
machine answers. 
•Ringer: Adjusts the ringer volume. For the ringer volume, you can 
select  Off, Low , Mid , and High. 
Speaker, ringer, key sound, and alarm sound
1.Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press the left/right arrow until  Sound/Volume appears and press 
OK .
3. Press the left/right arrow until t he sound option you want appears 
and press  OK.
4. Press the left/right arrow until the  desired status or volume for the 
sound you have selected appears and press  OK.
5. If necessary, repeat steps 3 through 5 to set other sounds.
6. Press  Stop/Clear  to return to ready mode.
Speaker volume
1.Press On Hook Dial. A dial tone sounds from the speaker.
2. Press the left/right arrow until  you hear the volume you want.
3. Press  Stop/Clear to save the change and return to ready mode.
Entering characters using the number keypad
As you perform various tasks, you may need to enter names and numbers. 
For example, when you set up your ma chine, you enter your name or your 
company’s name, and the fax number. When you store fax numbers or 
email addresses in memory, you may also enter the corresponding names.
Entering alphanumeric characters
1. When you are prompted to enter a  letter, locate the button labeled 
with the character you want. Press  the button until the correct letter 
appears on the display.
For example, to enter the letter  O, press 6 , labeled with  MNO.
Each time you press  6, the display shows a different letter,  M, N, O , 
m, n, o  and finally  6.
You can enter special characters, such as space, plus sign, and etc. 
For details, see  the below section.
2. To enter additional letters, repeat step 1.
If the next letter is printed on the same button, move the cursor by 
pressing the right
 arrow button and then press the button labeled 
with the letter you want. The cursor will move to the right and the 
next letter will appear on the display.
You can enter a space by  pressing the right arrow.
3. When you have finished entering letters, press  OK.
The date format may differ from country to country
You can adjust the volume level using On Hook Dial.
You can adjust the speaker volume only when the telephone line is 
connected.
Downloaded From ManualsPrinter.com Manuals 
						

							28 _Getting started
Keypad letters and numbers
Correcting numbers or names
If you make a mistake while enteri ng a number or name, press the left 
arrow button to delete the last digit  or character. Then enter the correct 
number or character.
Inserting a pause
With some telephone systems, you must dial an access code (9, for 
example) and listen for a second dial tone. In such cases, you must 
insert a pause in the telephone number. You can insert a pause while 
you are setting up speed buttons or speed dial numbers.
To insert a pause, press  Redial/Pause at the appropriate place while 
entering the telephone number. A -  appears on the display at the 
corresponding location.
Using the save modes
Toner Save mode
Toner save mode allows your machine to use less toner on each page. 
Activating this mode extends the life  of the toner cartridge beyond what 
one would experience in the normal mode, but it reduces print quality.
1. Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Toner Save appears and press OK .
4. Press the left/right arrow until the  time setting you want appears and 
press  OK.
5. Press  Stop/Clear to return to ready mode.
Power Save mode
Power Save mode allows your machine to reduce power consumption 
when it is not in actual use. You can turn this mode on and select a 
length of time for which the machine  waits after a job is printed before it 
switches to a reduced power state.
1. Press  Menu until System Setup appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Power Save appears and press  OK.
4. Press the left/right arrow until the  time setting you want appears and 
press  OK.
5. Press  Stop/Clear to return to ready mode.
Setting print job timeout
You can set the amount of time a single print job is active before it must 
print.The machine handles incoming data as a single job if it comes in within 
the specified time. When an error occu rs while processing data from the 
computer and the data flow stops, the machine waits the specified time and 
then cancels printing if data flow does not resume.
1. Press  Menu until System Setup  appears on the bottom line of the 
display and press  OK.
2. Press  OK when  Machine Setup  appears.
3. Press the left/right arrow until  Job Timeout appears and press  OK.
4. Press the left/right arrow until the time setting you want appears and 
press  OK.
5. Press  Stop/Clear  to return to ready mode.
KEYASSIGNED NUMBERS, LETTERS, OR CHARACTERS
1 @    /    .    ‘    1
2 A    B    C    a    b    c    2
3 D    E    F    d    e    f    3
4 G    H    I     g    h    i    4
5 J    K    L    j    k    l    5
6 M    N    O    m    n    o    6 
7 P    Q    R    S    p    q    r    s    7
8 T    U    V    t    u    v    8 
9 W    X    Y    Z    w    x    y    z    9
0 &    +    -    ,    0
Downloaded From ManualsPrinter.com Manuals 
						

							Getting started_29
Changing the font setting 
Your machine has preset the font  for your region or country. 
If you want to change the font or set the font for special condition such as 
the DOS environment, you can change  the font setting as follows:
1. Ensure that you have installed the  printer driver from the provided 
software CD.
2. Double-click the Smart Panel  icon on the Windows task bar.
3. Click  Printer Setting .
4. Click  Emulation .
5. Confirm if  PCL is selected in  Emulation Setting .
6. Click  Setting.
7. Select your prefe rred font in the Symbol set list.
8. Click  Apply .
Following information shows the proper font list for corresponding 
languages.
• Russian: CP866, ISO 8859/5 Latin Cyrillic
• Hebrew: Hebrew 15Q, Hebrew-8, Hebrew-7 (Israel only)
• Greek: ISO 8859/7 Latin Greek, PC-8 Latin/Greek
• Arabic & Farsi: HP Arabic-8, Windows Arabic, Code Page 864, 
Farsi, ISO 8859/6 Latin Arabic
• OCR : OCR-A, OCR-B
Downloaded From ManualsPrinter.com Manuals 
						

							Loading originals and print media_30
loading originals and print media
This chapter introduces you how to load originals and print media into your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Changing the size of the paper in the paper tray
• Loading paper • Printing on special print materials
• Adjusting the output support
• Setting the paper size and type
LOADING ORIGINALS
You can use the scanner glass or ADF to load an original for copying, 
scanning, and sending a fax.
On the scanner glass
Make sure that no originals are in the 
ADF. If an original is detected in the 
ADF, the machine gives it priority over  the original on the scanner glass. To 
get the best scan quality, especially for colored or gray-scaled images, use 
the scanner glass.
1. Lift and open the scanner lid.
2. Place the original face down on the scanner glass and align it with the 
registration guide at the top left corner of the glass. 3.
Close the scanner lid.
In the ADF
Using the ADF, you can load up to 30 sheets (SCX-4x24 Series), 50 sheets 
(SCX-4x28 Series) of paper (75 g/m2, 20 lb bond) for one job. 
When you use the ADF:
• Do not load paper smaller than 142 x 148 mm (5.6 x 5.8 inches) or  larger than 216 x 356 mm (8.5 x 14 inches).
• Do not attempt to load the following types of paper: - carbon-paper or carbon-backed paper
- coated paper
- onion skin or thin paper
- wrinkled or creased paper
- curled or rolled paper
- torn paper
• Remove all staples and paper clips before loading.
• Make sure any glue, ink, or correction fluid on the paper is completely  dry before loading.
• Do not load originals that include di fferent sizes or weights of paper.
• Do not load booklets, pamphlets, tr ansparencies, or documents having 
other unusual characteristics.
1. Flex or fan the edge of the paper stack to separate the pages before 
loading originals.
• Leaving the scanner lid open while copying may affect copy quality 
and toner consumption.
• Dust on the scanner glass may c ause black spots on the printout. 
Always keep it clean.
• If you are copying a page from a boo k or magazine, lift the scanner 
lid until its hinges are caught by  the stopper and then close the lid. 
If the book or magazine is thicker than 30 mm, start copying with 
the lid open.
Downloaded From ManualsPrinter.com Manuals