Runco X 450d Projector User Manual

Operation
Runco X-400d/X-450d Installation/Operation Manual 95 
PREL
IMINARY
Miscellaneous: Select Miscellaneous from the Service menu to set the following options: 
 Language: Select Language from the Miscellaneous menu and press the up- or 
down-arrows to select the OSD Language (English, Français, Deutsch, Italiano, 
Español, Svenska,  (Simplified Chinese),   (Traditional Chinese), 
Português,  (Russian),  (Japanese) or  (Korean)). 
SD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD...

Operation
96 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
HDMI: Select HDMI from the Service menu to set the following options affecting 
communication between HDMI sources, the Dimension Digital Controller and the 
X-400d/X-450d. 
 HDMI EDID Extension: Extended display identification data (EDID) is a data structure 
provided by a display device to describe its capabilities to a graphics card. It is what 
enables a modern personal computer to know what kind of monitor is connected....

Operation
Runco X-400d/X-450d Installation/Operation Manual 97 
PREL
IMINARY
 Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the 
brightness of the large, illuminated logo on the left side of the display. The range is from 
0 (off) to 31. 
Standby LED: Select Standby LED from the Front Panel Brightness menu to change 
the behavior of the front-panel STANDBY indicator LED. When set to ON, the LED 
lights amber when the system is in standby mode; otherwise, it is off. When set to...

Operation
98 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
4.2 
Using the 3D Glasses The 3D LCD Shutter Glasses function with the Runco Active 3D Emitter and the projector 
to provide unsurpassed 3D stereoscopic viewing. This section describes the features, 
connection, setup and operation of the 3D LCD Shutter Glasses. 
Key Features RF synchronization for uninterrupted 3D performance 
 Supports refresh rates from 50 to 240 Hz for compatibility with both current and future 
3D technology...

Operation
Runco X-400d/X-450d Installation/Operation Manual 99 
PREL
IMINARY
Charging the Battery The glasses must be fully charged before first use and whenever the Battery Status LED 
flashes red once every couple of seconds. The glasses will charge a completely dead 
battery in approximately five hours. You may use the glasses while the battery is being 
charged. 
To charge the 3D Glasses:
1. Attach one end of the supplied charging cable to the Power Input above the left lens 
on the glasses. 
2....

Operation
100 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Turning On the Glasses1. Ensure that the projector is powered on and displaying 3D content.
2. Press and hold the Power Button for about two seconds, then release the button. The 
LED will then blink in a pattern that indicates the battery charge state. In general, the 
more slowly and less frequently the LED blinks, the more charged (and less in need of 
charge) the glasses are. Refer to Table 4-5. 
3. The glasses will sync...

Maintenance and Troubleshooting
Runco X-400d/X-450d Installation/Operation Manual 101 
PREL
IMINARY
5.1 
Lamp ReplacementThe lamp should be replaced when it reaches the end of its life (typically between 2,000 
and 3,000 hours depending on the Lamp Power setting), or sooner if a noticeable 
degradation in brightness occurs. 
Keep track of the number of hours the lamp has been in use and be aware of any changes 
to brightness. These indicators will help you effectively maintain operation of the projector....

Maintenance and Troubleshooting
102 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
5.2 
Troubleshooting TipsTable 5-1 provides some general guidelines for troubleshooting problems you may 
encounter with the X-400d/X-450d. If the suggested solutions fail to resolve the problem 
or if you encounter an issue not described here, please contact Runco Technical Support. 
Table 5-1. Troubleshooting Chart
Symptom Possible Cause(s)Solution
The projector does not turn 
on.  The projector is not...

Maintenance and Troubleshooting
Runco X-400d/X-450d Installation/Operation Manual 103 
PREL
IMINARY
The display is jittery or 
unstable. Poor-quality or improperly 
connected source. 
 The horizontal or vertical 
scan frequency of the 
input signal may be out of 
range for the projector.  Ensure that the source is 
properly connected and of 
adequate quality for 
detection. 
 Correct at the source. 
Image is too bright and/or 
lacks definition in the bright 
areas of the image.  Contrast is set too high....

Maintenance and Troubleshooting
104 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
The projector does not turn 
on or respond to user com-
mands. The vacuum fluores-
cent display on the Dimension 
Digital Controller front panel 
displays the following mes-
sage:
Primary Display Error
Communication Failure The serial connection from 
the Dimension Digital 
Controller to the display is 
incorrect or the cable is 
faulty.  Ensure that the 
Pri. Display Control 
(RS-232) output from the...