Runco X 450d Projector User Manual

Operation
Runco X-400d/X-450d Installation/Operation Manual 85 
PREL
IMINARY
Splash Enable: When you have finished customizing the splash screen, select Splash 
Enable from the Splash Configure menu. Then, select On and press ENTER. 
OSD Position: To adjust the position of the OSD, select OSD Position from the 
Calibration menu and press ENTER. 
Press   or   to select “Hor.” or “Ver.” Then, press   or  to change the position. 
Service Use the Service menu to access advanced projector configuration...

Operation
86 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Press MENU to exit test pattern mode. 
Grey BarsUse this pattern when making 
brightness, contrast or white 
balance (gain/offset) adjustments. 
Full WhiteUse this pattern when measuring 
or adjusting brightness, contrast or 
white balance (gain/offset). 
Primary Alignment
Secondary 
Alignment
Dual AlignmentUse this pattern when aligning the 
output from the projector’s 
primary or secondary optical 
engines (refer to Adjusting...

Operation
Runco X-400d/X-450d Installation/Operation Manual 87 
PREL
IMINARY
Input Names: You can give each input a descriptive name. For example, you may want 
to change the default input name to the type of source component connected to it: 
“VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long. 
To edit an input name, select Input Names from the Service menu. Press   or   to select 
an input and press ENTER. Use the   or  buttons to change a character; press 
or  to select a...

Operation
88 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
When you change the Remote Code on the Dimension Digital Controller, you must 
re-program the Dimension Digital Controller remote control to send that same code. To 
enable “extended” key code mode, you must re-program the Dimension Digital 
Controller remote control with a special five-digit code reserved for that purpose. 
To do this:
1. Press and hold the LIGHT button on the 
remote control for approximately five seconds, 
or...

Operation
Runco X-400d/X-450d Installation/Operation Manual 89 
PREL
IMINARY
To change a button assignment, select the corresponding entry in the SRC 1-7 Keys or 
SRC 8-14 Keys sub-menu. Then, choose the source input you wish to assign to that 
button. 
Display Device - Configure: The options in the Display Device - Configure menu allow 
you to change the picture orientation, perform lens adjustments or access other, 
display-device specific functions. 
stallation – Orientation: Select Installation from...

Operation
90 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
splay 3D Settings: The Display 3D Settings menu is not applicable to the 
X-400d/X-450d.
 Internal 3D Settings: Select Internal 3D Settings from the Display Device - Configure 
menu to adjust the following timing settings for the Dimension Digital Controller’s 
3D Sync output (see Figure 2-5 and Figure 3-26), to optimize performance of the 
glasses, emitter and projector, for realistic simulation and 3D images.. 
Sync Delay: This...

Operation
Runco X-400d/X-450d Installation/Operation Manual 91 
PREL
IMINARY
Default Gateway: Select Default Gateway from the IP Configuration menu to 
manually configure the default IP gateway. The procedure is similar to that for setting 
the IP address. 
Communication Test: Select Communication Test from the IP Configuration menu 
to verify proper operation of the network communication link. 
To start the test, select Start Test from the Communication Test menu. The 
Dimension Digital Controller...

Operation
92 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
 E-Mail Notification: Select E-Mail Notification from the Network menu to specify 
when and to whom the Dimension Digital Controller sends error and service notification 
messages via e-mail.
The notification messages are in the following format:
To:  [E-Mail Address; see below]
From:  [email protected]
Subject:  [Type of notification] from Runco DC-300
Body:  
This is an automated message sent from the Runco DC-300:...

Operation
Runco X-400d/X-450d Installation/Operation Manual 93 
PREL
IMINARY
Periodic Service Notification: You can have the Dimension Digital Controller send 
periodic reminders via e-mail to perform regular maintenance tasks. To do this:
1. Select Periodic Service Notification from the E-Mail Notification menu. 
2. Highlight Enable and press ENTER. 
3. Highlight On and press ENTER. 
4. Press MENU.
5. Highlight Timer and press ENTER. 
6. Press   or   to set the notification interval in months. The range...

Operation
94 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
 Remote Network Control: Select Remote Network Control from the Network menu 
to enable or disable control of the Dimension Digital Controller via an IP connection 
(typically using a web browser). Set it to On to allow all incoming remote network 
connectivity. Set it to Off to disable any incoming network communication that was not 
initiated by the Dimension Digital Controller. 
Color Space: Select Color Space from the Service...