Runco X 450d Projector User Manual

Installation
Runco X-400d/X-450d Installation/Operation Manual 45 
PREL
IMINARY
SCART RGBS Source Connections: Connect the green, blue and red outputs from 
your SCART source to the Component/SCART input on the Dimension Digital Controller. 
Connect the sync output from your SCART source to the Video 1 input on the Dimension 
Digital Controller. See Figure 3-24. 
Figure 3-24. SCART RGBS Source Connections
Video 1 YVideo 2
Video 3
Pr Pb Component / SCARTTRIGGERS
12 3HD1
3D SYNC
HD2 DisplayPor
Video 2...

Installation
46 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Composite Source Connections: See Figure 3-25. 
Figure 3-25. Composite Video Source Connections
USB
Video 1 YVideo 2
Video 3
Pr PbHDMI 1
HDMI 2 Component / SCARTTRIGGERS
12 3HD1
3D SYNC
HD2 DisplayPor
Y
PrPb
USB
HDMI1
HDMI2
TRIGGERS123
HD1
3D SYNC
HD2DisplayPor
Gaming ConsoleVCR
Camcorder
Composite
Composite
Composite
Composite
Composite
Composite 

Installation
Runco X-400d/X-450d Installation/Operation Manual 47 
PREL
IMINARY
Connecting the Active 3D 
Emitter to the Dimension 
Digital Controller Connect the 3DSYNC IN port on the emitter to the 3D SYNC connector on the 
Dimension Digital Controller, as shown in Figure 3-26. 
Figure 3-26. Active 3D Emitter Connection
Connecting to AC Power Projector/Dimension Digital Controller: Plug the female end of one power cord into 
the AC receptacle on the rear of the X-400d/X-450d (AC 100V ~ 240V). Then,...

Installation
48 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
3.8 
Turning on the Power1. Power up your source components. 
2. If this is an AutoScope-equipped projector, turn on the main power switch at the rear 
of the AutoScope lens motor. The lens motor power switch is located next to the AC 
input (see Figure 3-17). 
3. Turn on the main power switch at the rear of the Dimension Digital Controller. 
4. Press the ON button on the remote control (or the ON/STA N D B Y ( ) button on the...

Installation
Runco X-400d/X-450d Installation/Operation Manual 49 
PREL
IMINARY
3.9 
Primary Lens 
Adjustments: Focus, 
Zoom and PositionLens zoom, focus and position are motorized adjustments that are adjustable using the 
remote control (Figure 2-6). This allows you to adjust the focus and image size while at the 
screen for more accurate results. 
To access the motorized lens controls:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Service from the Main...

Installation
50 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
3.11 
Adjusting the Image 
GeometryProjector and/or screen placement — among other things — can cause geometric 
distortion in the projected image. 
To correct this, the Dimension Digital Controller provides precise, nine-point control over 
the projected image geometry. Use these controls as (and only if) needed to re-position 
the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) 
or...

Installation
Runco X-400d/X-450d Installation/Operation Manual 51 
PREL
IMINARY
“Keystoning” usually occurs when the projector is tilted relative to the screen. “Pincushion” 
distortion can sometimes occur if the throw distance is very short and/or the projector is 
equipped with an anamorphic lens. 
To correct keystoning or pincushion distortion:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Calibration from the Main Menu and enter the Calibration Menu...

Installation
52 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
3.12 
Installing and 
Adjusting the 
CineWide Anamorphic 
LensIf you are installing an X-400d/X-450d/CineWide or X-400d/X-450d/CineWide with 
AutoScope, proceed as follows to install and adjust the secondary anamorphic lens. 
Runco offers two types of anamorphic lenses for its CineWide projectors: prismatic and 
cylindrical.
 The prismatic lens compresses the height of the image (as opposed to 
stretching the width) to achieve...

Installation
Runco X-400d/X-450d Installation/Operation Manual 53 
PREL
IMINARY
Cylindrical Anamorphic 
Lens Installation and 
Adjustment The Cylindrical Anamorphic lens mount kit consists of everything shown in Figure 3-29. 
Some components shipped with your projector may differ slightly from what is shown in 
these instructions. If any items are missing or damaged, please contact your Runco dealer 
or Runco Customer Service at (800) 23-RUNCO.
Figure 3-29. Cylindrical Anamorphic Lens Mounting Assembly -...

Installation
54 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Attach Lens Mounting Assembly to Lens Motor Carriage Plate: 
1. Remove the two Yaw/X Adjustment Levers and Washers (8) from the bottom of the 
Anamorphic Lens Holder (6).
2. Place the Anamorphic Lens Holder on top of the AutoScope Carriage Plate or Fixed 
CineWide Base Plate (7). Position the bracket so that the long slot at the bottom of 
the lens holder is perpendicular to the corresponding slots on the plate.
3. Secure the...