Runco X 450d Projector User Manual

Operation
Runco X-400d/X-450d Installation/Operation Manual 75 
PREL
IMINARY
To reset the Custom 1 or Custom 2 memory preset to its factory-default state, select it, 
press  or  to highlight Reset and press ENTER.
3D Processing Select 3D Processing from the Main Menu to set the following options related to 
formatting and delivery of HDMI 3D content.
3D Mode: Select 3D Mode from the 3D Processing menu to specify how the Dimension 
Digital Controller processes the “left eye” and “right eye” image...

Operation
76 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Sleep TimerSelect Sleep Timer from the Main Menu to turn off the X-400d/X-450d after a specified 
interval. Press   or   to select Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or 
4 Hours. Then, press ENTER. 
InformationSignal / System: Select Information from the Main Menu, then choose either Signal or 
System to display information about the current input signal (resolution, frequency, type et 
cetera) and installed...

Operation
Runco X-400d/X-450d Installation/Operation Manual 77 
PREL
IMINARY
Calibration Use the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the 
Memory Presets menu (see page 74) or use the corresponding remote control buttons. 
Display Color - Common Settings: Use the Display Color - Common Settings menu to 
adjust the color balance at the...

Operation
78 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
 Color Temp: Select Color Temp from the Display Color - Common Settings menu to 
adjust the color temperature. Color temperature establishes the “color of gray” by 
adjusting the 75% white point to various color points. 
What are “color points?”A “color point” is an x/y coordinate pair that defines a 
color’s location on the standard CIE chromaticity graph, shown in Figure 4-7. (CIE 
stands for “Commission Internationale de...

Operation
Runco X-400d/X-450d Installation/Operation Manual 79 
PREL
IMINARY
Table 4-2 lists the x- and y-coordinates for each color temperature preset in “Simple” 
mode. 
 Color Gamut: Select Color Gamut from the Display Color - Common Settings menu to 
select a color gamut (range) that may be different from the default color gamut. 
Each setting defines the precise hue of each primary (red, green and blue) and 
secondary (yellow, cyan and magenta) color component used to generate the millions 
of...

Operation
80 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Table 4-3 lists the Color Gamut settings and associated x- and y-coordinates for each 
primary and secondary color component. 
To use the Personal Color Equalizer to define a custom color gamut, choose the 
“PCE” Color Gamut setting (refer to Color Gamut on page 79). Then, choose PCE 
from the Display Color - Common Settings menu and press ENTER. 
PCE provides the ability to define a custom color gamut in terms of a “white point”...

Operation
Runco X-400d/X-450d Installation/Operation Manual 81 
PREL
IMINARY
The Auto Color Enable and Test Pattern Enable checkboxes let you choose what to 
display on-screen while making these adjustments. These controls work together as 
follows:
 
 YCM (Yellow, Cyan, Magenta): To precisely adjust the secondary color points 
associated with the custom color gamut, choose YCM from the PCE sub-menu. Each 
control operates only on the color specified. Surrounding colors are linearly interpolated 
based...

Operation
82 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
stantContrast (X-400d only): Select ConstantContrast from the Display Color - 
Projector Settings menu to enable (On) or disable (Off) ConstantContrast in the optical 
engine. ConstantContrast uses a dynamic iris that modulates light to the DMD based 
on the actual content of the video material. Runco recommends that you disable 
ConstantContrast before adjusting Brightness, Contrast or other image settings. 
Input Image: The...

Operation
Runco X-400d/X-450d Installation/Operation Manual 83 
PREL
IMINARY
   Copy/Paste - Memory Preset: You can copy and paste settings from one memory 
preset to another. This gives you a convenient starting point for creating a new preset 
based on an existing one, to make the calibration process less time-consuming. 
For example, you can use the Copy/Paste Memory Preset feature to:
 Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
 Calibrate an input for 720p source signals, then use...

Operation
84 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
spect Ratio - Paste Settings: To apply the Output Shift, Image Alignment and 
Screen Masking settings on the clipboard to a different aspect ratio and/or screen, do 
either of the following:
 Switch to another aspect ratio (for example, from 16:9 to Cinema).
 Switch from Screen 1 to Screen 2 or vice versa.
Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings 
are saved automatically.
Output Shift:...