Runco X 450d Projector User Manual

Runco X-400d/X-450d Installation/Operation Manual 105 
PREL
IMINARY
In addition to using the Dimension Digital Controller front-panel keypad or remote control 
unit, there are three methods of controlling the X-400d/X-450d and Dimension Digital 
Controller externally: 
 Using a serial (RS-232) or TCP/IP (Ethernet) link to send ASCII commands and receive 
responses to those commands.
 Using discrete infrared (IR) codes to program a third-party remote control unit.
 Using an HDMI connection to send...

External Control
106 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Command FormatCommands sent from an automation/control system or PC to the Dimension Digital 
Controller must have the following format:
(www:xyz) [CR]
Where:
( and ) indicate the start and end of the command data. If these characters are 
present, the Dimension Digital Controller assumes that valid command data is present 
in the command string. Otherwise, the Dimension Digital Controller ignores the 
command.
www...

External Control
Runco X-400d/X-450d Installation/Operation Manual 107 
PREL
IMINARY
 11 = Password not entered
www indicates the command code. This field is case insensitive; for example, PWR, pwr 
and PwR are all equivalent.
:x is the destination parameter.  This is an optional parameter that indicates which 
memory the command is referencing.  This parameter is reserved for future use.
z is the new value (for Set, Increment or Decrement commands) or the current value 
(for Get commands) for this...

External Control
108 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Apply Image Alignment Values AIA R/W No 0 1 No 0 = Off; 1 = On
Altitude ALT R/W No 0 1 No 0 = Auto
1 = High
Advanced Color Temp Mode 
EnableAME R/W No 0 1 No 0 = Off; 1 = On
Auto New Firmware Check ANF R/W No 0 1 No 0 = Off; 1 = On
Auto Power Off Enable APE R/W No 0 2 No 0 = Off; 1 = On; 2 = No Signal
Auto Power Off Timer APT R/W Yes 1 24 No
Auto Perform Upgrade APU R/W No 0 1 No 0 = Off; 1 = On
Aspect Ratio Copy ARC W No...

External Control
Runco X-400d/X-450d Installation/Operation Manual 109 
PREL
IMINARY
ConstantContrast
(X-400d only)CCT R/W No 0 4 No 0 = Off
1 = On
2 = Low
3 = Medium
4 = High
CEC Enable CEC R/W No 0 1 No 0 = Off; 1 = On
Chroma Delay CHR R/WYes07No
Color Gamut CLG R/WYes06No0 = Auto
1 = REC709
2 = SMPTE C
3 = EBU
4 = Native
6 = PCE
Color Offset CLO R/W Yes -50 50 No Picture menu
Color CLR R/W Yes -50 50 No Calibration -> Input Image menu
Color Space CLS R/W No 0 4 No 0 = REC601
1 = REC709
2 = RGB
3 = RGB...

External Control
110 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Diagnostic Color DGC R/W No 0 6 No 0 = White
1 = Red
2 = Green
3 = Blue
4 = Yellow
5 = Cyan
6 = Magenta
Display Green Gain DGG R/W Yes -100 100 No
Display Green Offset DGO R/W Yes -100 100 No
DHCP DHC R/W No 0 1 No 0 = Off; 1 = On
Display Red Gain DRG R/W Yes -100 100 No
Display Red Offset DRO R/W Yes -100 100 No
Error Notification ERN R/W No 0 1 No 0 = Off; 1 = On
Error Code ERR R No 0 No 0 = None
1 = Display Lamp...

External Control
Runco X-400d/X-450d Installation/Operation Manual 111 
PREL
IMINARY
24Hz 3D Mode FRC R/W No 1 2 No 1 = 120Hz 6:4
2 = 120Hz 5:5
Firmware Upgrade FWU W No N/A N/A No Action will be performed on any 
setting value
Gamma Advanced GMA R/W Yes 0 20 No
Gamma Mode GMM R/W No 0 1 No 0 = Simple
1 = Advanced
Gamma Simple GMS R/W No 0 4 No 0 = 2.0
1 = 1.8
2 = 2.2
3 = 2.35
4 = 2.5
HDMI Audio Format HAF R/W No 0 3 No 0 = Combined
1 = HDMI Out (Pri. Display)
2 = HDMI Out (Sec. Display)
3 = HDMI Out...

External Control
112 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Information Copied Aspect Ratio ICA R No N/A N/A Yes
Information Current Color Space ICC R No 0 3 Yes 0 = REC601
1 = REC709
2 = RGB
3 = RGB Video
Information Copied Input Source ICI R No N/A N/A Yes
Information Copied Memory Pre-
setICM R No N/A N/A Yes
Information Copied Screen ICR R No N/A N/A Yes
Information Copied Signal Format ICS R No N/A N/A Yes
Information Display Name IDN R No N/A N/A Yes
Information Firmware...

External Control
Runco X-400d/X-450d Installation/Operation Manual 113 
PREL
IMINARY
Input Position Height IPH R/W Yes 0 20 No
Input Position Left Right IPL R/W Yes -50 50 No
Input Position Up Down IPU R/W Yes -50 50 No
Input Position Width IPW R/W Yes 0 50 No
Input Red Gain IRG R/W Yes -32 32 No
Input Red Offset IRO R/W Yes -32 32 No
Internal 3D Sync Delay ISD R/W Yes Var. Var. No
Information Signal Format ISF R No N/A N/A Yes
Information Serial Number ISN R No N/A N/A Yes
Information Sync Type IST R No...

External Control
114 Runco X-400d/X-450d Installation/Operation Manual
PREL
IMINARY
Remote Key KEY W No 0 85 No 1 = On
2 = Off
3 = Menu
4 = Enter
5 = Up
6 = Down
7 = Left
8 = Right
9 = 16:9
10 = 4:3
11 = Letterbox
12 = VirtualWide
13 = Video 1
14 = Component
17 = HD 1
18 = HD 2
19 = HDMI 1
20 = HDMI 2
21 = HDMI 3
22 = HDMI 4
23 = SCART
24 = Video 2
25 = Video 3
32 = Sleep Timer Off
33 = Sleep Timer 30 Mins
34 = Sleep Timer 60 Mins
35 = Sleep Timer 90 Mins
36 = Sleep Timer 2 Hours
37 = Sleep Timer 4...