Runco Ls 12hbd Projector User Manual

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 45 
PREL
IMINARY
Component Video Source Connections: Connect your component video sources to 
the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-17. 
Figure 3-17. Component Video Source Connections
USB
To Accessory  Box
Video 1 YVideo 2
Video 3
Pr PbHDMI 1
HDMI 2HDMI 3
HDMI 4 Component / SCARTTRIGGERS
RS-232
12 3
HD1
3D SYNC
HD2 DisplayPor
USB
ToAccessory Box
Video 2
Video3
HDMI1
HDMI 2
HDMI3
HDMI4
TRIGGERSRS-2321233D SYNC...

Installation
46 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
RGBHV Source Connections: Connect personal computers and/or other RGB sources 
to the HD1 and/or HD2 inputs as shown in Figure 3-18. 
Figure 3-18. RGBHV Source Connections
Video 1 YVideo 2
Video 3
Pr Pb Component / SCARTTRIGGERS
12 3HD1
3D SYNC
HD2 DisplayPor
or
Video 1YVideo2
Video 3PrPb
Component / SCART
TRIGGERS1233D SYNC
DisplayPor
ComputerRGB Camcorder 

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 47 
PREL
IMINARY
SCART RGBS Source Connections: Connect the green, blue and red outputs from 
your SCART source to the Component/SCART input on the Dimension Digital Controller. 
Connect the sync output from your SCART source to the Video 1 input on the Dimension 
Digital Controller. See Figure 3-19. 
Figure 3-19. SCART RGBS Source Connections
Video 1 YVideo 2
Video 3
Pr Pb Component / SCARTTRIGGERS
12 3HD1
3D SYNC
HD2 DisplayPor
Video 2...

Installation
48 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Composite Source Connections: See Figure 3-20. 
Figure 3-20. Composite Video Source Connections
USB
Video 1 YVideo 2
Video 3
Pr PbHDMI 1
HDMI 2 Component / SCARTTRIGGERS
12 3HD1
3D SYNC
HD2 DisplayPor
Y
PrPb
USB
HDMI1
HDMI2
TRIGGERS123
HD1
3D SYNC
HD2DisplayPor
Gaming ConsoleVCR
Camcorder
Composite
Composite
Composite
Composite
Composite
Composite 

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 49 
PREL
IMINARY
Connecting the Active 3D 
Emitter to the Dimension 
Digital Controller Connect the 3DSYNC Out port on the emitter to the 3D Sync Out connector on the 
Dimension Digital Controller, as shown in Figure 3-21. Mount the emitter in a location that 
provides a clear line of sight between it and the viewing area.
Figure 3-21. Active 3D Emitter Connection
Connecting to AC Power Projector: Plug the female end of one power cord into...

Installation
50 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
3.8 
Turning on the Power1. Power up your source components. 
2. Turn on the main power switch at the rear of the Dimension Digital Controller. 
3. Press the ON button on the remote control (or the ON/STA N D B Y ( ) button on the 
Dimension Digital Controller front panel) to turn on the system. The vacuum 
fluorescent display on the Dimension Digital Controller front panel briefly displays 
“Initializing System,” followed by...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 51 
PREL
IMINARY
3.9 
Primary Lens 
Adjustments: Focus, 
Zoom and PositionLens zoom, focus and position are motorized adjustments that are adjustable using the 
remote control (Figure 2-7). This allows you to adjust the focus and image size while at the 
screen for more accurate results. 
To access the motorized lens controls:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Service from the Main...

Installation
52 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
3.11 
Adjusting the Image 
GeometryProjector and/or screen placement — among other things — can cause geometric 
distortion in the projected image. 
To correct this, the Dimension Digital Controller provides precise, nine-point control over 
the projected image geometry. Use these controls as (and only if) needed to re-position 
the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) 
or...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 53 
PREL
IMINARY
“Keystoning” usually occurs when the projector is tilted relative to the screen. “Pincushion” 
distortion can sometimes occur if the throw distance is very short and/or the projector is 
equipped with an anamorphic lens. 
To correct keystoning or pincushion distortion:
1. On the Dimension Digital Controller remote control or front panel, press MENU.
2. Select Calibration from the Main Menu and enter the Calibration Menu...

Installation
54 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
3.12 
Installing and 
Adjusting the 
Anamorphic LensIf you are installing an LS-12HBd with an anamorphic lens, proceed as follows to install 
and adjust the lens. 
Attach the anamorphic lens to the bracket using the plastic knobs supplied with the lens. 
See Figure 3-24. 
Figure 3-24. Attaching the Anamorphic Lens to the Lens Mount
Configure Lens Motor Trigger on Dimension Digital Controller: The anamorphic 
lens solution for...