Runco Ls 12hbd Projector User Manual

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 35 
PREL
IMINARY
3.6 
Mounting the 
Dimension Digital 
ControllerThe Dimension Digital Controller unit can be placed on any flat, stable surface such as a 
shelf or table, or it can be rack-mounted using the supplied mounting hardware. Place it in 
a location that provides easy access to the power connectors. 
The Dimension Digital Controller unit requires 2U (3.5 inches) or more of vertical rack 
space. 
To mount the Dimension Digital...

Installation
36 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
3.7 
System 
InterconnectionsProceed as follows to connect the LS-12HBd system components to each other and to 
AC power.
When connecting your equipment:
 Turn off all equipment before making any connections.
 Use the correct signal cables for each source. 
 For best performance and to minimize cable clutter, use high-quality cables that are 
only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 37 
PREL
IMINARY
Figure 3-9 shows how to connect the Dimension Digital Controller to the projector. 
Figure 3-9. Connecting the Dimension Digital Controller to the Projector
RS232RS232PRIMARYPRIMARYSECONDARYSECONDARY3D Sync Out3D Sync Out
Video 1 YVideo 2
Video 3
Pr PbIR Pri. Display Control Sec. Display Control
HDMI 2 HDMI 4 HDMI 6 HDMI 8
EthernetHDMI Out
To Sec. Display
HDMI Out
To Pri. Display HDMI Out
Audio OnlyComponent / SCARTTRIGGERS...

Installation
38 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Connecting an Audio
Processor or Secondary
Display Device to the
Dimension Digital
Controller (Optional)The Dimension Digital Controller provides a second HDMI output (labeled HDMI Out 
(Audio Only)) for connection to an audio receiver/switching system or secondary display 
device for monitoring purposes. See Figure 3-10. 
Figure 3-10. Audio Processor Connection to Dimension Digital Controller➤
The Dimension Digital...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 39 
PREL
IMINARY
Additional Connections to 
the Dimension Digital 
Controller (Optional)  The Dimension Digital Controller provides the following interfaces to external equipment 
that allow it to control or be controlled by that equipment:
 An RS-232 interface to a PC or control/automation system;
 Three (3), 12-volt trigger outputs;
 An infrared (IR) repeater input;
 An Ethernet network interface for firmware updates and maintenance...

Installation
40 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Connecting 12-volt Trigger Outputs to External Equipment: If your LS-12HBd is 
equipped with an anamorphic lens, connect the +12V Trigger Input on the lens transport 
to a 12-volt trigger output on the Dimension Digital Controller; see Figure 3-12. 
Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or 
screen masks) to the other trigger outputs. 
Figure 3-12. Connecting 12-volt Trigger...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 41 
PREL
IMINARY
Connecting an External IR Receiver to the Dimension Digital Controller: If infrared 
signals from the remote control cannot reach the Dimension Digital Controller due to 
excessive distance or obstructions such as walls or cabinet doors, you can connect an 
external IR receiver to extend the range of the remote control. See Figure 3-13. 
Figure 3-13. External IR Receiver Connection
RS-232
IRPri. Display Control Sec. Display...

Installation
42 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Ethernet Network Connection: Use a standard, Category 5 network cable with an 
RJ-45 plug to connect a network hub, router or gateway to the Ethernet port on the 
Dimension Digital Controller; see Figure 3-14. 
Figure 3-14. Ethernet Network Connection to Dimension Digital Controller
PC / ControlRS-232
IR
Control Sec. Display Control
HDMI 7
HDMI 8
Ethernet
HDMI Out
To Sec. Display
HDMI Out
To Pri. Display HDMI Out
Audio OnlyPC...

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 43 
PREL
IMINARY
Connecting Source 
Components to the 
Dimension Digital 
Controller  Connect your video sources to the Dimension Digital Controller as shown and described 
in the sections that follow. 
DisplayPort Source Connection: See Figure 3-15. 
Figure 3-15. DisplayPort Source Connection
USB
To Accessory 
Video 1 YVideo 2
Video 3
Pr PbHDMI 1
HDMI 2HDMI 3
HDMI 4 Component / SCARTTRIGGERS
RS-232
12 3
HD1
3D SYNC
HD2 DisplayPort
USB...

Installation
44 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
HDMI Source Connections: See Figure 3-16. 
Figure 3-16. HDMI Source Connections Use the HDMI inputs whenever possible. This ensures the highest 
video quality because the signal is carried in the digital domain 
throughout the entire signal path, from source component output 
into the projector. 
You can also connect computers with DVI output to these inputs. 
Refer to Supported Timings on page 129 for a list of compatible...