Runco Ls 12hbd Projector User Manual

System Overview
LightStyle™ LS-12HBd Installation/Operation Manual 5 
PREL
IMINARY
A LightStyle™ Series LS-12HBd Active 3D Projection System consists of the following 
components: 
 The projector (equipped with dual digital video inputs) with optional anamorphic lens 
and lens transport assembly. 
 The DC-300 Dimension Digital Controller™ unit that provides “left-eye” and “right-eye“ 
video signals and the on-screen display (OSD) menu to the projector. In addition, the 
Dimension Digital Controller...

System Overview
6 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
2.1 
ProjectorA LightStyle™ Series LS-12HBd Active 3D Projection System can display both traditional 
2D and stereoscopic 3D video content. 
An active 3D presentation requires a specialized video signal source configuration and 
content to be displayed correctly. Images from a stereo 3D video source consist of a 
series of images (called frames or fields) that alternate quickly between two slightly 
different view points,...

System Overview
LightStyle™ LS-12HBd Installation/Operation Manual 7 
PREL
IMINARY

Provides an alternative to using the remote control unit to perform primary lens 
adjustments (focus, zoom and position). 
FOCUS, H/V, ZOOM
Use these buttons to select the type of lens adjustment you wish to make. The default 
function (following a power cycle) is FOCUS. 
Cursor Buttons ( , , , ) 
Use these buttons to perform the selected lens adjustment. These buttons operate as 
follows:
 When adjusting focus, the up (...

System Overview
8 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Figure 2-3. LS-12HBd Rear/Bottom/Top View
RUNCO LOGO BADGE
REAR COVER
Remove to access connectors. 
LAMP MODULE COVER
Remove this cover to access the lamp compartment.
CABLE OPENING
Pass cables through this opening.
CEILING MOUNT HOLES 
Use these to attach the ceiling bracket to the projector. Use M4 screws with a 
maximum screw depth of 10 mm (0.39 inch). 
ADJUSTABLE FEET
Use these when the projector is installed in a...

System Overview
LightStyle™ LS-12HBd Installation/Operation Manual 9 
PREL
IMINARY
2.2 
LS-12HBd Rear PanelFigure 2-4 shows the LS-12HBd rear panel.
Figure 2-4. LS-12HBd Rear Panel
1.RS232 (Control)
A female, 9-pin D-sub connector that provides a serial communication link to the 
Dimension Digital Controller, via its Pri. Display Control output (see Figure 2-6). 
2.3D LED
Lights green when the projector is displaying 3D content.
3.PRIMARY VIDEO INPUT 
Connect the HDMI Out To Primary Display connector...

System Overview
10 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
2.3 
DC-300 Dimension 
Digital ControllerThe Dimension Digital Controller provides “left-eye” and “right-eye” video signals and the 
OSD menu to the projector. It controls the other system components in response to user 
input via the following interfaces:
 Front-panel keypad
 IR remote control unit
 HDMI CEC messages
 RS-232 serial commands

Front Panel LayoutFigure 2-5 shows the controls and indicators on the Dimension...

System Overview
LightStyle™ LS-12HBd Installation/Operation Manual 11 
PREL
IMINARY
6.DOWN BUTTON
Use to direct-select aspect ratios or move the menu cursor down in the OSD. When 
no menu is present on-screen, this button toggles through aspect ratios in the 
following order: 
16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema - Native
7.RIGHT BUTTON
Used to direct-select inputs or move the menu cursor right in the OSD. When no 
menus are present on-screen, the RIGHT button toggles through...

System Overview
12 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Rear Panel LayoutFigure 2-6 shows the rear connector panel on the Dimension Digital Controller.
Figure 2-6. DC-300 Dimension Digital Controller Rear Panel
1.MAIN POWER SWITCH
Disconnects or applies power to the Dimension Digital Controller.
2.3D Sync Out
A 3-pin, VESA standard mini-DIN connector for connecting the Runco Active 3D 
Emitter to the Dimension Digital Controller. 
3.TRIGGERS 
Connection for up to three (3),...

System Overview
LightStyle™ LS-12HBd Installation/Operation Manual 13 
PREL
IMINARY
11.DisplayPort
DisplayPort 1.1a and DisplayPort-HDCP 1.1 compliant, SD/HD input for connecting 
SDTV, EDTV or HDTV component video sources.
12.HD1 / HD2 In (15-pin VGA)
Two inputs for connecting standard-definition (SD = 480i/576i), enhanced-definition 
(ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p) component video 
sources, or RGBHV sources such as personal computers. 
13.Component / SCART In (3 x RCA...

System Overview
14 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
2.4 
LS-12HBd Remote 
Control Unit Figure 2-7 shows the LS-12HBd remote control, and the paragraphs that follow describe 
its functionality.
Figure 2-7. Dimension Digital Controller Remote Control Unit for LS-12HBd 
The LS-12HBd remote control unit supports an “extended” key 
code mode that allows certain buttons to perform alternate 
functions. The following list identifies those buttons that have both 
standard and...