Runco Ls 12hbd Projector User Manual

Installation
LightStyle™ LS-12HBd Installation/Operation Manual 55 
PREL
IMINARY
6. Select the Cinema aspect ratio to move the anamorphic lens into position, if it isn’t 
already. To do this, press CINEMA on the Dimension Digital Controller remote control 
(Figure 2-7), or press   or  repeatedly with no menus visible on-screen. 
Adjusting the Lens Position: 
1. Adjust the vertical position and tilt of the lens so that the projector beam is passing 
through the center of the lens and any residual...

Installation
56 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Notes: 

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 57 
PREL
IMINARY
4.1 
Using the On-Screen 
MenusTo display the Main Menu, press the MENU button on the remote control or Dimension 
Digital Controller front panel (Figure 2-5). 
To select a menu item, use the   and   buttons on the remote control or Dimension 
Digital Controller front panel to highlight it. Then, to confirm your selection, press ENTER 
on the remote control or Dimension Digital Controller front panel. 
The LS-12HBd OSD menus...

Operation
58 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Figure 4-1. LS-12HBd OSD Menu Structure (continued) Service
Test VideoColor Bars 1
Color Bars 2
Focus
Grey Bars
Full White
Primary / Secondary / Dual 
Alignment
3D
Input Names Rename/Restore
Remote ControlRemote Code 00000 ... 08209 ... 65535 or 88999 (extended 
mode) 
SRC 1-7 Keys
(select a key, then choose a source to assign to it)
SRC 8-14 Keys
Display Device - ConfigureInstallation - 
Picture OrientationAuto, Floor Front,...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 59 
PREL
IMINARY
Main Menu The Main Menu is the starting point for accessing all Dimension Digital Controller 
functions. 
(You must enter a passcode to access the Calibration and Service menus.)
Input Source From the Main Menu, select Input Source to choose a video signal source. 
The active source is indicated by an arrow (Î) to its left; in this example, Composite is the 
active source. 
Runco Video
Input Source
Aspect Ratio
Screen
Picture...

Operation
60 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Aspect RatioTo change the aspect ratio (size and shape) of the projected image, select Aspect Ratio 
from the Main Menu and press ENTER. Select the appropriate aspect ratio for your 
screen size and the type of program material being viewed; refer to Table 4-1. 
The currently-selected aspect ratio is indicated by a “
7” to its left; in this example, 16:9 is 
selected. 
Note that some aspect ratios are unavailable and/or not...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 61 
PREL
IMINARY
Letterbox LET
BOXLetterbox mode scales (zooms 
in on) a 4:3 image linearly (by the 
same amount on all sides) to fill 
a 16:9 display. 
Letterbox is best suited for 
viewing LaserDisc movies or 
non-anamorphic DVDs on a 
16:9 screen.
VirtualWide V-WIDE VirtualWide scales a 4:3 image 
NON-linearly (more on the sides 
than in the center) to fit a 16:9 
screen. 
On a 2.35:1 screen, the image is 
centered between black bars on...

Operation
62 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
ScreenThe Screen Menu allows you to recall multiple sets of stored values for certain controls 
(Output Shift, Image Alignment and Screen Masking) that are saved for each aspect ratio. 
Such settings are also saved “per screen.” To recall the Output Shift and Image Alignment 
settings associated with “Screen 1” or “Screen 2,” make that selection here.
Virtual Cinema V-CINE A 16:9 image is scaled 
NON-linearly (more on the sides...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 63 
PREL
IMINARY
Picture Use the controls in the Picture Menu to calibrate each Dimension Digital Controller input to 
achieve optimum picture quality.
The Dimension Digital Controller has been designed to incorporate setup and calibration 
standards established by the Imaging Science Foundation (ISF). The ISF has developed 
carefully crafted, industry-recognized standards for optimal video performance and has 
implemented a training program...

Operation
64 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an 
acronym for “Picture Line-Up Generation Equipment.”) Figure 4-2 shows a typical PLUGE 
pattern.
Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, white and gray 
areas against a black background. The example above includes two vertical bars and four 
shaded...