Runco Ls 12hbd Projector User Manual

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 85 
PREL
IMINARY
To change a button assignment, select the corresponding entry in the SRC 1-7 Keys or 
SRC 8-14 Keys sub-menu. Then, choose the source input you wish to assign to that 
button. 
Display Device - Configure: The options in the Display Device - Configure menu allow 
you to change the picture orientation, perform lens adjustments or access other, 
display-device specific functions. 
stallation – Orientation: Select Installation from...

Operation
86 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
splay 3D Settings: The Display 3D Settings menu is not applicable to the 
LS-12HBd.
 Internal 3D Settings: Select Internal 3D Settings from the Display Device - Configure 
menu to adjust the following timing settings for the Dimension Digital Controller’s 
3D Sync output (see Figure 2-6 and Figure 3-21), to optimize performance of the 
glasses, emitter and projector, for realistic simulation and 3D images. 
Sync Delay: This...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 87 
PREL
IMINARY
Default Gateway: Select Default Gateway from the IP Configuration menu to 
manually configure the default IP gateway. The procedure is similar to that for setting 
the IP address. 
Communication Test: Select Communication Test from the IP Configuration menu 
to verify proper operation of the network communication link. 
To start the test, select Start Test from the Communication Test menu. The 
Dimension Digital Controller...

Operation
88 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
 E-Mail Notification: Select E-Mail Notification from the Network menu to specify 
when and to whom the Dimension Digital Controller sends error and service notification 
messages via e-mail.
The notification messages are in the following format:
To:  [E-Mail Address; see below]
From:  [email protected]
Subject:  [Type of notification] from Runco DC-300
Body:  
This is an automated message sent from the Runco DC-300:...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 89 
PREL
IMINARY
Periodic Service Notification: You can have the Dimension Digital Controller send 
periodic reminders via e-mail to perform regular maintenance tasks. To do this:
1. Select Periodic Service Notification from the E-Mail Notification menu. 
2. Highlight Enable and press ENTER. 
3. Highlight On and press ENTER. 
4. Press MENU.
5. Highlight Timer and press ENTER. 
6. Press   or   to set the notification interval in months. The...

Operation
90 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
 Remote Network Control: Select Remote Network Control from the Network menu 
to enable or disable control of the Dimension Digital Controller via an IP connection 
(typically using a web browser). Set it to On to allow all incoming remote network 
connectivity. Set it to Off to disable any incoming network communication that was not 
initiated by the Dimension Digital Controller. 
Color Space: Select Color Space from the...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 91 
PREL
IMINARY
Miscellaneous: Select Miscellaneous from the Service menu to set the following options: 
 Language: Select Language from the Miscellaneous menu and press the up- or 
down-arrows to select the OSD Language (English, Français, Deutsch, Italiano, 
Español, Svenska,  (Simplified Chinese),   (Traditional Chinese), 
Português,  (Russian),  (Japanese) or  (Korean)). 
SD Timer: Select OSD Timer from the Miscellaneous menu to set the...

Operation
92 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
HDMI: Select HDMI from the Service menu to set the following options affecting 
communication between HDMI sources, the Dimension Digital Controller and the 
LS-12HBd. 
 HDMI EDID Extension: Extended display identification data (EDID) is a data structure 
provided by a display device to describe its capabilities to a graphics card. It is what 
enables a modern personal computer to know what kind of monitor is connected. 
Some...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 93 
PREL
IMINARY
 Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the 
brightness of the large, illuminated logo on the left side of the display. The range is from 
0 (off) to 31. 
Standby LED: Select Standby LED from the Front Panel Brightness menu to change 
the behavior of the front-panel STANDBY indicator LED. When set to ON, the LED 
lights amber when the system is in standby mode; otherwise, it is off. When set to...

Operation
94 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
4.2 
Using the 3D Glasses The 3D LCD Shutter Glasses function with the Runco Active 3D Emitter and the projector 
to provide unsurpassed 3D stereoscopic viewing. This section describes the features, 
connection, setup and operation of the 3D LCD Shutter Glasses. 
Key Features RF synchronization for uninterrupted 3D performance 
 Supports refresh rates from 50 to 240 Hz for compatibility with both current and future 
3D...