Runco Ls 12hbd Projector User Manual

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 75 
PREL
IMINARY
Table 4-2 lists the x- and y-coordinates for each color temperature preset in “Simple” 
mode. 
 Color Gamut: Select Color Gamut from the Display Color - Common Settings menu to 
select a color gamut (range) that may be different from the default color gamut. 
Each setting defines the precise hue of each primary (red, green and blue) and 
secondary (yellow, cyan and magenta) color component used to generate the millions 
of...

Operation
76 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Table 4-3 lists the Color Gamut settings and associated x- and y-coordinates for each 
primary and secondary color component. 
To use the Personal Color Equalizer to define a custom color gamut, choose the 
“PCE” Color Gamut setting (refer to Color Gamut on page 75). Then, choose PCE 
from the Display Color - Common Settings menu and press ENTER. 
PCE provides the ability to define a custom color gamut in terms of a “white...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 77 
PREL
IMINARY
The Auto Color Enable and Test Pattern Enable checkboxes let you choose what to 
display on-screen while making these adjustments. These controls work together as 
follows:
 
 YCM (Yellow, Cyan, Magenta): To precisely adjust the secondary color points 
associated with the custom color gamut, choose YCM from the PCE sub-menu. Each 
control operates only on the color specified. Surrounding colors are linearly interpolated 
based...

Operation
78 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Input Image: The Input Image controls are functionally similar to those in the Picture 
menu (refer to page 63), but are accessible only by entering the Calibration menu 
passcode. 
Input Color: The Input Color controls are similar to those in the Display Color menu (see 
above), but adjust the color balance of the incoming signal. These settings are also saved 
independently for each input and display mode.
set (HD1, HD2 and...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 79 
PREL
IMINARY
   Copy/Paste - Memory Preset: You can copy and paste settings from one memory 
preset to another. This gives you a convenient starting point for creating a new preset 
based on an existing one, to make the calibration process less time-consuming. 
For example, you can use the Copy/Paste Memory Preset feature to:
 Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
 Calibrate an input for 720p source signals, then use...

Operation
80 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
spect Ratio - Paste Settings: To apply the Output Shift, Image Alignment and 
Screen Masking settings on the clipboard to a different aspect ratio and/or screen, do 
either of the following:
 Switch to another aspect ratio (for example, from 16:9 to Cinema).
 Switch from Screen 1 to Screen 2 or vice versa.
Then, select Paste Settings from the Copy/Paste Aspect Ratio menu. The new settings 
are saved automatically.
Output Shift:...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 81 
PREL
IMINARY
Splash Enable: When you have finished customizing the splash screen, select Splash 
Enable from the Splash Configure menu. Then, select On and press ENTER. 
OSD Position: To adjust the position of the OSD, select OSD Position from the 
Calibration menu and press ENTER. 
Press   or   to select “Hor.” or “Ver.” Then, press   or  to change the position. 
Service Use the Service menu to access advanced projector configuration...

Operation
82 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Press MENU to exit test pattern mode. 
Grey BarsUse this pattern when making 
brightness, contrast or white 
balance (gain/offset) adjustments. 
Full WhiteUse this pattern when measuring 
or adjusting brightness, contrast or 
white balance (gain/offset). 
Primary Alignment
Secondary 
Alignment
Dual AlignmentUse this pattern when aligning the 
output from the projector’s 
primary or secondary optical 
engines (refer to Adjusting...

Operation
LightStyle™ LS-12HBd Installation/Operation Manual 83 
PREL
IMINARY
Input Names: You can give each input a descriptive name. For example, you may want 
to change the default input name to the type of source component connected to it: 
“VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12 characters long. 
To edit an input name, select Input Names from the Service menu. Press   or   to select 
an input and press ENTER. Use the   or  buttons to change a character; press 
or  to select a...

Operation
84 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
When you change the Remote Code on the Dimension Digital Controller, you must 
re-program the Dimension Digital Controller remote control to send that same code. To 
enable “extended” key code mode, you must re-program the Dimension Digital 
Controller remote control with a special five-digit code reserved for that purpose. 
To do this:
1. Press and hold the LIGHT button on the 
remote control for approximately five seconds, 
or...