Runco Ls 12hbd Projector User Manual
Have a look at the manual Runco Ls 12hbd Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation LightStyle™ LS-12HBd Installation/Operation Manual 35 PREL IMINARY 3.6 Mounting the Dimension Digital ControllerThe Dimension Digital Controller unit can be placed on any flat, stable surface such as a shelf or table, or it can be rack-mounted using the supplied mounting hardware. Place it in a location that provides easy access to the power connectors. The Dimension Digital Controller unit requires 2U (3.5 inches) or more of vertical rack space. To mount the Dimension Digital Controller in a standard, 19-inch equipment rack, install the mounting ears on either side of the chassis using the supplied screws; see Figure 3-7. Then, secure the mounting ears to the rack. Figure 3-7. Attaching the Rack Mounting Hardware
Installation 36 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY 3.7 System InterconnectionsProceed as follows to connect the LS-12HBd system components to each other and to AC power. When connecting your equipment: Turn off all equipment before making any connections. Use the correct signal cables for each source. For best performance and to minimize cable clutter, use high-quality cables that are only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.) Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connecting the Dimension Digital Controller to the ProjectorDigital Video Connection: Connect the HDMI Out To Pri. Display connector on the Dimension Digital Controller to the PRIMARY input on the projector. Similarly connect the HDMI Out To Sec. Display connector on the Dimension Digital Controller to SECONDARY input on the projector. RS-232 Connection: Connect the Pri. Display Control output from the Dimension Digital Controller to the RS232 input on the projector. Use a standard, modular telephone cable with RJ11 plugs at both ends. On the projector end, use the provided RJ11-to-DB9 adapter. This adapter is wired as shown in Figure 3-8. Figure 3-8. RS-232 Connection from the Dimension Digital Controller to the Projector ➤ Runco recommends using the RS-232 communication link between the LS-12HBd projector and the Dimension Digital Controller. However, display control using HDMI CEC control messages is also possible. For more information on this capability, please contact Runco Technical Support. 4 3RCV DATA 3 2 XMT DATA XMT DATA RCV DATA 25 SIG GND NO CONNECTION 1, 5, 61, 4, 6, 7, 8, 9 To/From Dimension Digital Controller 6-position RJ-11 MaleDB-9 Male 6 11 6 RS232RS232 Note
Installation LightStyle™ LS-12HBd Installation/Operation Manual 37 PREL IMINARY Figure 3-9 shows how to connect the Dimension Digital Controller to the projector. Figure 3-9. Connecting the Dimension Digital Controller to the Projector RS232RS232PRIMARYPRIMARYSECONDARYSECONDARY3D Sync Out3D Sync Out Video 1 YVideo 2 Video 3 Pr PbIR Pri. Display Control Sec. Display Control HDMI 2 HDMI 4 HDMI 6 HDMI 8 EthernetHDMI Out To Sec. Display HDMI Out To Pri. Display HDMI Out Audio OnlyComponent / SCARTTRIGGERS 12 3 3D SYNC HD2 DisplayPort Video1YVideo2 Video 3PrPb IRSec. Display Control HDMI2HDMI 4HDMI6HDMI 8EthernetHDMI OutAudio Only Component / SCART TRIGGERS1233D SYNC HD2DisplayPortrr Dimension Digital Controller
Installation 38 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY Connecting an Audio Processor or Secondary Display Device to the Dimension Digital Controller (Optional)The Dimension Digital Controller provides a second HDMI output (labeled HDMI Out (Audio Only)) for connection to an audio receiver/switching system or secondary display device for monitoring purposes. See Figure 3-10. Figure 3-10. Audio Processor Connection to Dimension Digital Controller➤ The Dimension Digital Controller does not transmit HDMI CEC control messages from the “HDMI Audio Out” connector. Note USB To Accessory Box o 2 o 3PC / ControlRS-232 IR Pri. Display Control Sec. Display Control HDMI 1 HDMI 2HDMI 3 HDMI 4HDMI 5 HDMI 6HDMI 7 HDMI 8 Ethernet HDMI Out To Sec. Display HDMI Out To Pri. Display HDMI Out Audio Only RS-2323USB ToAccessory Box o 2 o3 PC / Control RS-232IRPri. Display ControlSec. Display Control HDMI1 HDMI2 HDMI3 HDMI4 HDMI5 HDMI6 HDMI7 HDMI8Ethernet HDMI OutTo Sec. Display HDMI OutToPri Display RS-2323 or Audio Processor/ SwitcherSecondary Display
Installation LightStyle™ LS-12HBd Installation/Operation Manual 39 PREL IMINARY Additional Connections to the Dimension Digital Controller (Optional) The Dimension Digital Controller provides the following interfaces to external equipment that allow it to control or be controlled by that equipment: An RS-232 interface to a PC or control/automation system; Three (3), 12-volt trigger outputs; An infrared (IR) repeater input; An Ethernet network interface for firmware updates and maintenance notifications. The following sections describe how to make these interface connections. RS-232 Controller Connection: Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation system (if present) to the RS-232 port on the Dimension Digital Controller; see Figure 3-11. Figure 3-11. RS-232 Control System Connection to Dimension Digital Controller PC / ControlRS-232 IR Pri. Display Control Sec. Display Control HDMI 5 HDMI 6HDMI 7 HDMI 8 Ethernet HDMI Out To Sec. Display HDMI Out To Pri. Display HDMI Out Audio Only IRPri. Display ControlSec. Display Control HDMI5 HDMI6 HDMI 7 HDMI 8Ethernet HDMI OutTo Sec. Display HDMI OutTo Pri. DisplayHDMI OutAudio Only 12345 7896 to Automation/ Control System or PC 2 Receive Data(to ctrl. system) 3 Transmit Data(from ctrl. system) 5 Ground(none of the other pins are used)
Installation 40 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY Connecting 12-volt Trigger Outputs to External Equipment: If your LS-12HBd is equipped with an anamorphic lens, connect the +12V Trigger Input on the lens transport to a 12-volt trigger output on the Dimension Digital Controller; see Figure 3-12. Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or screen masks) to the other trigger outputs. Figure 3-12. Connecting 12-volt Trigger Outputs USB To AccessoVideo 1 YVideo 2 Video 3 Pr PbHDMI 1 HDMI 2HDMI 3 HDMI 4 Component / SCARTTRIGGERS RS-23 212 3 HD1 D SYNC HD2 USB ToAccessoVideo 1YVideo2 Video 3PrPb HDMI 1 HDMI2 HDMI3 HDMI4 Component / SCART RS-232 HD1 D SYNC HD2 Tip = +12V Sleeve = Ground Anamorphic Lens Transport (Rear View) 3.5-mm mini plug +12V Trigger Input Retractable Screen or other 12-volt trigger-activated device
Installation LightStyle™ LS-12HBd Installation/Operation Manual 41 PREL IMINARY Connecting an External IR Receiver to the Dimension Digital Controller: If infrared signals from the remote control cannot reach the Dimension Digital Controller due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR receiver to extend the range of the remote control. See Figure 3-13. Figure 3-13. External IR Receiver Connection RS-232 IRPri. Display Control Sec. Display Control DMI 5 DMI 6HDMI 7 HDMI 8 Ethernet HDMI Ou To Sec. Display HDMI Out To Pri. Display HDMI Out Audio Only RS-232Pri. Display ControlSec. Display Control DMI5 DMI6 HDMI7 HDMI8Ethernet HDMI OuToSec. Display HDMI OutToPri. DisplayHDMI OutAudio Only (3.5-mm, mini phono plug) IR Sensor IR RepeaterRemote Control
Installation 42 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY Ethernet Network Connection: Use a standard, Category 5 network cable with an RJ-45 plug to connect a network hub, router or gateway to the Ethernet port on the Dimension Digital Controller; see Figure 3-14. Figure 3-14. Ethernet Network Connection to Dimension Digital Controller PC / ControlRS-232 IR Control Sec. Display Control HDMI 7 HDMI 8 Ethernet HDMI Out To Sec. Display HDMI Out To Pri. Display HDMI Out Audio OnlyPC / Control RS-232IRControlSec. Display Control HDMI7 HDMI8 HDMI OutTo Sec. Display HDMI OutToPri. DisplayHDMI OutAudio Only 1 8 to Ethernet Hub, Router or Gateway1 Transmit Data + 2 Transmit Data - 3 Receive Data + 6 Receive Data -
Installation LightStyle™ LS-12HBd Installation/Operation Manual 43 PREL IMINARY Connecting Source Components to the Dimension Digital Controller Connect your video sources to the Dimension Digital Controller as shown and described in the sections that follow. DisplayPort Source Connection: See Figure 3-15. Figure 3-15. DisplayPort Source Connection USB To Accessory Video 1 YVideo 2 Video 3 Pr PbHDMI 1 HDMI 2HDMI 3 HDMI 4 Component / SCARTTRIGGERS RS-232 12 3 HD1 3D SYNC HD2 DisplayPort USB ToAccessory Video 1YVideo2 Video 3PrPb HDMI1 HDMI2 HDMI3 HDMI4 Component / SCART TRIGGERSRS-232123 HD1 3D SYNC HD2 Notebook Computer or Other DisplayPort Source
Installation 44 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY HDMI Source Connections: See Figure 3-16. Figure 3-16. HDMI Source Connections Use the HDMI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector. You can also connect computers with DVI output to these inputs. Refer to Supported Timings on page 129 for a list of compatible input signals. Tip Note USB To Accessory Bo Video 2 Video 3PC / ControRS-232 IR Pri. Display Control Sec. Display Control HDMI 1 HDMI 2HDMI 3 HDMI 4HDMI 5 HDMI 6HDMI 7 HDMI 8 EthernetHDMI Out To Sec. Display HDMI To Pri. D HDMI Out Audio Only RS-232 3USB ToAccessory Bo Video2 Video3 PC / Contro RS-232IRPri. Display ControlSec. Display Control Ethernet HDMI OutToSec. Display HDMI To Pri. DHDMI OutAudio Only RS-2323 HDMI AV OUT HDMI source (BD, DVD, DTV Set-Top Box etc.)