Runco Ls 12hbd Projector User Manual

							External Control
LightStyle™ LS-12HBd Installation/Operation Manual 105 
PREL
IMINARY
Image Alignment Center x CNX R/W Yes -100 100 No
Image Alignment Center y CNY R/W Yes -100 100 No
Contrast CON R/W Yes -50 50 No Calibration -> Input Image menu
Contrast Offset COO R/W Yes -50 50 No Picture menu
Color Temp Simple CTS R/W No 0 4 No 1 = 5500K
2 = 6500K
3 = 7500K
4 = 9300K
CUE CUE R/W No 0 1 No 0 = Off; 1 = On
Display Blue Gain DBG R/W Yes -100 100 No
Display Blue Offset DBO R/W Yes -100 100 No
Default Gateway Byte 1 DE1 R/W Yes 0 255 No
Default Gateway Byte 2 DE2 R/W Yes 0 255 No
Default Gateway Byte 3 DE3 R/W Yes 0 255 No
Default Gateway Byte 4 DE4 R/W Yes 0 255 No
DisplayPort EDID Extension DEE R/W No 0 1 No 0 = Off; 1 = On
Diagnostic Color DGC R/W No 0 6 No 0 = White
1 = Red
2 = Green
3 = Blue
4 = Yellow
5 = Cyan
6 = Magenta
Display Green Gain DGG R/W Yes -100 100 No
Display Green Offset DGO R/W Yes -100 100 No
DHCP DHC R/W No 0 1 No 0 = Off; 1 = On
Display Red Gain DRG R/W Yes -100 100 No
Display Dark Interval DRK R/W Yes Var. Var. No
Display Red Offset DRO R/W Yes -100 100 No
Error Notification ERN R/W No 0 1 No 0 = Off; 1 = On
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
106 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Error Code ERR R No 0 No 0 = None
1 = Display Lamp Overtemp
2 = Display Ballast Overtemp
3 = Display Fan Init Failure
4 = Display Fan 1 Failure
5 = Display Fan 2 Failure
6 = Display Fan 3 Failure
7 = Display Fan 4 Failure
8 = Display Fan 5 Failure
9 = Display Fan 6 Failure
10 = Display Fan 7 Failure
11 = Display Fan 8 Failure
12 = Display DMD Failure
13 = Display Lamp Strike Failure
14 = Display Lamp Went Out
15 = Display Ballast UART Failure
16 = Display GPIO Failure
17 = Display Lamp Door Open
18 = Display Processor Failure
19 = Display Hardware I2C Failure
20 = Display Software I2C Failure
21 = Display Lamp Error
22 = Display Communication Error
25 = DC-300 Fan 1 Failure
26 = DC-300 Fan 2 Failure
27 = DC-300 Overtemp 1
28 = DC-300 Overtemp 2
56 = DC-300 Fan 3 Failure
58 = DC-300 Overtemp 3
60 = DC-300 Input FPGA Failure
61 = DC-300 Output FPGA Failure
Focus FCS W Yes 0 0 No Send 
(FCS+) or (FCS-) to 
adjust incrementally 
Film Mode FLM R/W No 0 1 No 0 = Off; 1 = On
24Hz 3D Mode FRC R/W No 1 2 No 1 = 120Hz 6:4
2 = 120Hz 5:5
Firmware Upgrade FWU W No N/A N/A No Action will be performed on any 
setting value
Gamma Advanced GMA R/W Yes 0 20 No
Gamma Mode GMM R/W No 0 1 No 0 = Simple
1 = Advanced
Gamma Simple GMS R/W No 0 4 No 0 = 2.0
1 = 1.8
2 = 2.2
3 = 2.35
4 = 2.5
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
LightStyle™ LS-12HBd Installation/Operation Manual 107 
PREL
IMINARY
HDMI Audio Format HAF R/W No 0 3 No 0 = Combined
1 = HDMI Out (Pri. Display)
2 = HDMI Out (Sec. Display)
3 = HDMI Out (Audio Only) 
HDMI EDID Extension 1
HDMI EDID Extension 2
HDMI EDID Extension 3
HDMI EDID Extension 4
HDMI EDID Extension 5
HDMI EDID Extension 6
HDMI EDID Extension 7
HDMI EDID Extension 8HE1
HE2
HE3
HE4
HE5
HE6
HE7
HE8R/W No 0 1 No 0 = Off; 1 = On
HPD Toggle Rejection HPD R/W No 0 1 No 0 = Off; 1 = On
Horizontal Shift HSH W Yes 0 0 No Send 
(HSH+) or (HSH-) to 
adjust incrementally 
Input Name 1
Input Name 2
Input Name 3
Input Name 4
Input Name 5
Input Name 6
Input Name 7
Input Name 8
Input Name 9
Input Name 10
Input Name 11
Input Name 12
Input Name 13
Input Name 14
Input Name 15
Input Name 16I01
I02
I03
I04
I05
I06
I07
I08
I09
I10
I11
I12
I13
I14
I15
I16R/W No N/A N/A Yes 12 characters maximum
Input Blue Gain IBG R/W Yes -32 32 No
Input Blue Offset IBO R/W Yes -32 32 No
Information Boot Version IBV R No N/A N/A Yes
Information Copied Aspect Ratio ICA R No N/A N/A Yes
Information Current Color Space ICC R No 0 3 Yes 0 = REC601
1 = REC709
2 = RGB
3 = RGB Video
Information Copied Input Source ICI R No N/A N/A Yes
Information Copied Memory Pre-
setICM R No N/A N/A Yes
Information Copied Screen ICR R No N/A N/A Yes
Information Copied Signal Format ICS R No N/A N/A Yes
Information Display Name IDN R No N/A N/A Yes
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
108 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Information Firmware Version IFV R No N/A N/A Yes
Input Green Gain IGG R/W Yes -32 32 No
Input Green Offset IGO R/W Yes -32 32 No
Information Horizontal Frequency IHF R No N/A N/A Yes
Information Input Resolution IIR R No N/A N/A Yes
Information Input FPGA Version IIV R No N/A N/A Yes
information Micro Version IMV R No N/A N/A Yes
Input Source INS R/W No 0 15 No 0 = Composite 1
1 = Composite 2
2 = Composite 3
3 = Component
4 = HD 1
5 = HD 2
6 = SCART
7 = HDMI 1
8 = HDMI 2
9 = HDMI 3
10 = HDMI 4
11 = HDMI 5
12 = HDMI 6
13 = HDMI 7
14 = HDMI 8
15 = DisplayPort
Information Output Resolution IOR R No N/A N/A Yes
Information Output FPGA Version IOV R No N/A N/A Yes
IP Address Byte 1 IP1 R/W Yes 0 255 No
IP Address Byte 2 IP2 R/W Yes 0 255 No
IP Address Byte 3 IP3 R/W Yes 0 255 No
IP Address Byte 4 IP4 R/W Yes 0 255 No
Information Pixel Clock IPC R No N/A N/A Yes
Input Position Height IPH R/W Yes 0 20 No
Input Position Left Right IPL R/W Yes -50 50 No
Input Position Up Down IPU R/W Yes -50 50 No
Input Position Width IPW R/W Yes 0 50 No
Input Red Gain IRG R/W Yes -32 32 No
Input Red Offset IRO R/W Yes -32 32 No
Internal 3D Sync Delay ISD R/W Yes Var. Var. No
Information Signal Format ISF R No N/A N/A Yes
Information Serial Number ISN R No N/A N/A Yes
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
LightStyle™ LS-12HBd Installation/Operation Manual 109 
PREL
IMINARY
Information Sync Type IST R No 0 3 No 0 = None
1 = Separate
2 = Composite
3 = Sync-on-green
Information Vertical Frequency IVF R No N/A N/A Yes
Remote Key KEY W No 0 85 No 1 = On
2 = Off
3 = Menu
4 = Enter
5 = Up
6 = Down
7 = Left
8 = Right
9 = 16:9
10 = 4:3
11 = Letterbox
12 = VirtualWide
13 = Video 1
14 = Component
17 = HD 1
18 = HD 2
19 = HDMI 1
20 = HDMI 2
21 = HDMI 3
22 = HDMI 4
23 = SCART
24 = Video 2
25 = Video 3
32 = Sleep Timer Off
33 = Sleep Timer 30 Mins
34 = Sleep Timer 60 Mins
35 = Sleep Timer 90 Mins
36 = Sleep Timer 2 Hours
37 = Sleep Timer 4 Hours
38 = Screen 1
39 = Screen 2
44 = Cinema
45 = Virtual Cinema
46 = Native
48 = ISF Night
49 = ISF Day
50 = Custom 1
51 = Custom 2
52 = Exit Remote Key Repeat KRT W No 0 85 No
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
110 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Remote Key Repeat (cont.) KRT W No 0 85 No 64 = Keypad Menu 
(used internally)
65 = Power Toggle 
(used internally)
66 = Enter Key Up (used internally)
67 = SRC 1
68 = SRC 2
69 = SRC 3
70 = SRC 4
71 = SRC 5
72 = SRC 6
73 = SRC 7
74 = SRC 8
75 = SRC 9
76 = SRC 10
77 = SRC 11
78 = SRC 12
79 = SRC 13
80 = SRC 14
81 = HDMI 5
82 = HDMI 6
83 = HDMI 7
84 = HDMI 8
85 = DisplayPort
86 = Auto Cinema
Language LAN R/W No 0 9 No 0 = English
1 = French
2 = German
3 = Italian
4 = Spanish
5 = Portuguese
6 = Simplified Chinese
7 = Traditional Chinese
8 = Swedish
9 = Russian
10 = Japanese
11 = Korean
Lens Home Position LHP W No N/A N/A No Action will be performed on any 
setting value
Lamp Hours Reset LHR W No N/A N/A No Action will be performed on any 
setting value
Lamp Hours LHS R No 0 (Note) No Max = 2,147,483,647
Image Alignment Left Middle x LMX R/W Yes -100 100 No
Image Alignment Left Middle y LMY R/W Yes -100 100 No
Lamp Life Notification Enable LNE R/W No 0 1 No 0 = Off; 1 = On
Lamp Life Notification Hours LNH R/W Yes 100 10,000 No
Logo LED Brightness LOG R/W Yes 0 31 No
Lamp Power LPW R/W Yes -1 0 No -1 = 230W; 0 = 260W
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
LightStyle™ LS-12HBd Installation/Operation Manual 111 
PREL
IMINARY
Display Serial Number LSN R No N/A N/A Yes
Model Name MDL R No N/A N/A Yes
Memory Preset MMP R/W No 0 3 No 0 = ISF Night
1 = ISF Day
2 = Custom 1
3 = Custom 2
Memory Preset Copy MPC W No N/A N/A No
Action will be performed on any 
setting value
Memory Preset Paste MPP W No N/A N/A No
Memory Preset Reset MPR W No 0 3 No 0 = ISF Night
1 = ISF Day
2 = Custom 1
3 = Custom 2 Memory Preset Save MPS W No 0 3 No
Noise Filter NFL R/W Yes 0 10 No Calibration -> Input Color menu
Noise Filter Offset NFO R/W Yes 0 10 No Picture menu
Orientation ORI R/W No0 4 No 0 = Floor Front
1 = Ceiling Front
2 = Floor Rear
3 = Ceiling Rear
4 = Auto
OSD Position Horizontal OSD R/W Yes 0 100 No
Output Shift Height OSH R/W Yes -50 0 No
Output Shift Left Right OSL R/W Yes -300 300 No
OSD Message Enable OSM R/W No 0 1 No 0 = Off; 1 = On
OSD Timer OST R/W Yes 0 60 No Values from 1-4 are not allowed; if 
increment or decrement is used, 
these values will be skipped.
Output Shift Up Down OSU R/W Yes -200 200 No
OSD Position Vertical OSV R/W Yes 0 100 No
Output Shift Width OSW R/W Yes -50 0 No
Overscan Mode OVM R/W No 0 1 No 0 = Zoom
1 = Crop
Overscan OVS R/W Yes 0 20 No
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
112 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Programmable Source Key 
[1 ... 14]P01
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14R/W No 0 15 No 0 = Composite 1
1 = Composite 2
2 = Composite 3
3 = Component
4 = HD 1
5 = HD 2
6 = SCART
7 = HDMI 1
8 = HDMI 2
9 = HDMI 3
10 = HDMI 4
11 = HDMI 5
12 = HDMI 6
13 = HDMI 7
14 = HDMI 8
15 = DisplayPort
PCE Cyan X PCX R/W Yes -100 100 No
PCE Cyan Y PCY R/W Yes -100 100 No
Phase PHS R/W Yes 0 31 No
PCE Magenta X PMX R/W Yes -100 100 No
PCE Magenta Y PMY R/W Yes -100 100 No
Periodic Notification Enable PNE R/W No 0 1 No 0 = Off; 1 = On
Periodic Notification Months PNM R/W Yes 1 255 No
Power PWR R/W No 0 1 No 0 = Off; 1 = On
PCE Yellow X PYX R/W Yes -100 100 No
PCE Yellow Y PYY R/W Yes -100 100 No
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
LightStyle™ LS-12HBd Installation/Operation Manual 113 
PREL
IMINARY
Input Name 1 Restore R01 W No N/A N/A No
Action will be performed on any 
setting value Input Name 2 Restore R02 W No N/A N/A No
Input Name 3 Restore R03 W No N/A N/A No
Input Name 4 Restore R04 W No N/A N/A No
Input Name 5 Restore R05 W No N/A N/A No
Input Name 6 Restore R06 W No N/A N/A No
Input Name 7 Restore R07 W No N/A N/A No
Input Name 8 Restore R08 W No N/A N/A No
Input Name 9 Restore R09 W No N/A N/A No
Input Name 10 Restore R10 W No N/A N/A No
Input Name 11 Restore R11 W No N/A N/A No
Input Name 12 Restore R12 W No N/A N/A No
Input Name 13 Restore R13 W No N/A N/A No
Input Name 14 Restore R14 W No N/A N/A No
Input Name 15 Restore R15 W No N/A N/A No
Input Name 16 Restore R16 W No N/A N/A No
Remote Code RMN R/W Yes 0 65535 No
Image Alignment Right Middle x RMX R/W Yes -100 100 No
Remote Network Control RNC R/W No 0 1 No 0 = Off; 1 = On
Standby LED Enable SBL R/W No 0 1 No 0 = Off; 1 = On
Splash Configure String 1 SC1 R/W No N/A N/A Yes
30 characters max Splash Configure String 2 SC2 R/W No N/A N/A Yes
Splash Configure String 3 SC3 R/W No N/A N/A Yes
Sidebar Color Blue SCB R/W Yes 0 255 No
Sidebar Color Green SCG R/W Yes 0 255 No
Screen SCN R/W No 0 1 No 0 = Screen 1
1 = Screen 2
Sidebar Color Red SCR R/W Yes 0 255 No
Send Errors to Runco SER R/W No 0 1 No 0 = Off; 1 = On
Sharpness Offset SHO R/W Yes -50 50 No
Sharpness SHP R/W Yes -50 50 No
Screen Masking Bottom SMB R/W Yes 0 200 No
Screen Masking Test Pattern 
EnableSME R/W No 0 1 No 0 = Off; 1 = On
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes 
						

							External Control
114 LightStyle™ LS-12HBd Installation/Operation Manual
PREL
IMINARY
Screen Masking Left SML R/W Yes 0 200 No
Screen Masking Test Pattern 
Mode EnableSMM R/W No 0 1 No 0 = Off; 1 = On
Screen Masking Right SMR R/W Yes 0 200 No
Screen Masking Top SMT R/W Yes 0 200 No
Splash Enable SPE R/W No 0 1 No 0 = Off; 1 = On
Splash Timer SPT R/W Yes 5 60 No
Status STA RNo04No
Sync Threshold STH R/W Yes 0 15 No
Sleep Timer STM R/W No 0 5 No 0 = Off
1 = 30 Minutes
2 = 60 Minutes
3 = 90 Minutes
4 = 2 Hours
5 = 4 Hours
Subnet Mask Byte 1 SU1 R/W Yes 0 255 No
Subnet Mask Byte 2 SU2 R/W Yes 0 255 No
Subnet Mask Byte 3 SU3 R/W Yes 0 255 No
Subnet Mask Byte 4 SU4 R/W Yes 0 255 No
System Reset SYS W No N/A N/A No Action will be performed on any 
setting value
Table 6-1. Serial Commands (continued)
SettingCommand 
CodeRead/
WriteInc/
DecMin 
ValueMax 
ValueString? Notes