Runco Ls 12hbd Projector User Manual
Have a look at the manual Runco Ls 12hbd Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation LightStyle™ LS-12HBd Installation/Operation Manual 45 PREL IMINARY Component Video Source Connections: Connect your component video sources to the HD1, HD2 and/or Component/SCART inputs as shown in Figure 3-17. Figure 3-17. Component Video Source Connections USB To Accessory Box Video 1 YVideo 2 Video 3 Pr PbHDMI 1 HDMI 2HDMI 3 HDMI 4 Component / SCARTTRIGGERS RS-232 12 3 HD1 3D SYNC HD2 DisplayPor USB ToAccessory Box Video 2 Video3 HDMI1 HDMI 2 HDMI3 HDMI4 TRIGGERSRS-2321233D SYNC DisplayPor Y PBPR COMPONEN T VIDEO OUT BD/DVD DTV-Set-Top Box (DTV-STB)
Installation 46 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY RGBHV Source Connections: Connect personal computers and/or other RGB sources to the HD1 and/or HD2 inputs as shown in Figure 3-18. Figure 3-18. RGBHV Source Connections Video 1 YVideo 2 Video 3 Pr Pb Component / SCARTTRIGGERS 12 3HD1 3D SYNC HD2 DisplayPor or Video 1YVideo2 Video 3PrPb Component / SCART TRIGGERS1233D SYNC DisplayPor ComputerRGB Camcorder
Installation LightStyle™ LS-12HBd Installation/Operation Manual 47 PREL IMINARY SCART RGBS Source Connections: Connect the green, blue and red outputs from your SCART source to the Component/SCART input on the Dimension Digital Controller. Connect the sync output from your SCART source to the Video 1 input on the Dimension Digital Controller. See Figure 3-19. Figure 3-19. SCART RGBS Source Connections Video 1 YVideo 2 Video 3 Pr Pb Component / SCARTTRIGGERS 12 3HD1 3D SYNC HD2 DisplayPor Video 2 Video3 HD1 HD2DisplayPor TRIGGERS1233D SYNC Gaming ConsoleVCR DVD/DTV STB SCART-to-RGBS adapter Green Blue Red Sync Green Blue Red Sync
Installation 48 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY Composite Source Connections: See Figure 3-20. Figure 3-20. Composite Video Source Connections USB Video 1 YVideo 2 Video 3 Pr PbHDMI 1 HDMI 2 Component / SCARTTRIGGERS 12 3HD1 3D SYNC HD2 DisplayPor Y PrPb USB HDMI1 HDMI2 TRIGGERS123 HD1 3D SYNC HD2DisplayPor Gaming ConsoleVCR Camcorder Composite Composite Composite Composite Composite Composite
Installation LightStyle™ LS-12HBd Installation/Operation Manual 49 PREL IMINARY Connecting the Active 3D Emitter to the Dimension Digital Controller Connect the 3DSYNC Out port on the emitter to the 3D Sync Out connector on the Dimension Digital Controller, as shown in Figure 3-21. Mount the emitter in a location that provides a clear line of sight between it and the viewing area. Figure 3-21. Active 3D Emitter Connection Connecting to AC Power Projector: Plug the female end of one power cord into the AC receptacle on the rear of the LS-12HBd (AC 100V ~ 240V). Then, connect the other end to your AC power source. Anamorphic Lens Transport: An AC-to-DC power adapter is provided for the lens transport. Connect the power adapter to the +9V DC In jack on the rear of the lens transport assembly. Connect the other end to an AC power source. Similarly connect the Dimension Digital Controller to a nearby AC outlet. Secure the emitter in the desired location using double-sided tape or a similar adhesive material. Tip USB Video 1 YVideo 2 Video 3 Pr Pb HDMI 2 Component / SCARTTRIGGERS 12 3HD1 3D SYNC HD2DisplayPort USB Video 1YVideo 2 Video3PrPbHDMI2 Component / SCART TRIGGERS 123 HD1 HD2DisplayPortrr Active 3D Emitter 3D SYNC IN
Installation 50 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY 3.8 Turning on the Power1. Power up your source components. 2. Turn on the main power switch at the rear of the Dimension Digital Controller. 3. Press the ON button on the remote control (or the ON/STA N D B Y ( ) button on the Dimension Digital Controller front panel) to turn on the system. The vacuum fluorescent display on the Dimension Digital Controller front panel briefly displays “Initializing System,” followed by “Starting LS-12HBd.” 4. When the display is ready for use, the fluorescent display indicates the active source, input resolution/frame rate and aspect ratio/screen; for example: 5. When the projector is turned on, the Active 3D Emitter turns on as well. The LEDs display a red moving pattern while the emitter attempts to acquire a 3D signal and until a signal is found. If the emitter searches for a signal for longer than 60 seconds, a signal is assumed to not be present. 6. Upon finding a 3D signal, all LEDs turn blue. Once the LEDs indicate a 3D signal, the 3D glasses can be used to experience 3D. For more information on using the Active 3D Glasses, refer to Using the 3D Glasses on page 94. HDMI 1 16:9/1 1080i/60 Current Source Aspect Ratio/ScreenInput Resolution/Frame Rate LS-12HBd 1080p/60 Searching for 3D Sync Signal 3D Sync Signal Found
Installation LightStyle™ LS-12HBd Installation/Operation Manual 51 PREL IMINARY 3.9 Primary Lens Adjustments: Focus, Zoom and PositionLens zoom, focus and position are motorized adjustments that are adjustable using the remote control (Figure 2-7). This allows you to adjust the focus and image size while at the screen for more accurate results. To access the motorized lens controls: 1. On the Dimension Digital Controller remote control or front panel, press MENU. 2. Select Service from the Main Menu and enter the Service Menu passcode. 3. Select Display Device from the Service Menu. 4. Select Configure from the Display Device menu, then select Lens. The Lens menu controls operate as described below. Focus To focus the projected image, use the cursor buttons to highlight “In” or “Out.” Then, press and hold the ENTER button. Zoom To make the picture smaller (zoom out), use the cursor buttons to highlight the minus sign (-). Then, press and hold the ENTER button. To enlarge the picture (zoom in), use the cursor buttons to highlight the plus sign (+). Then, press and hold the ENTER button. Vertical and Horizontal Lens Shift To change the lens position, use the cursor buttons to highlight “Left,” “Right,” “Up” or “Down” in the Lens menu. Then, press and hold the ENTER button to shift the lens in that direction. To return the lens to its home position (no horizontal or vertical shift), use the cursor buttons to highlight “Home” in the Lens menu. Then, press the ENTER button. 3.10 Adjusting the Picture OrientationBy default, the LS-12HBd is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this: 1. On the Dimension Digital Controller remote control or front panel, press MENU. 2. Select Service from the Main Menu and enter the Service Menu passcode. 3. Select Display Device from the Service Menu. 4. Select Configure from the Display Device menu, then select Installation. 5. Select Orientation, then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match the installation method. If you prefer, you can also perform lens adjustments from the projector using the built-in keypad. For detailed instructions, refer to KEYPAD on page 7. You must enter a passcode to access the Service menu. Note Note You must enter a passcode to access the Service menu. Note
Installation 52 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY 3.11 Adjusting the Image GeometryProjector and/or screen placement — among other things — can cause geometric distortion in the projected image. To correct this, the Dimension Digital Controller provides precise, nine-point control over the projected image geometry. Use these controls as (and only if) needed to re-position the image corners, mid-points and center to eliminate “keystoning” (mis-aligned corners) or “pincushion” distortion (mid-points not aligned with corners). See Figure 3-22. Figure 3-22. Keystone and Pincushion Distortion Vertical Keystoning Horizontal K e y s t o n i n g Pincushion Distortion
Installation LightStyle™ LS-12HBd Installation/Operation Manual 53 PREL IMINARY “Keystoning” usually occurs when the projector is tilted relative to the screen. “Pincushion” distortion can sometimes occur if the throw distance is very short and/or the projector is equipped with an anamorphic lens. To correct keystoning or pincushion distortion: 1. On the Dimension Digital Controller remote control or front panel, press MENU. 2. Select Calibration from the Main Menu and enter the Calibration Menu passcode. 3. Select Image Alignment from the Calibration Menu. 4. Select Corner Alignment to correct a “keystoned” image by adjusting the image corner positions. Select Midpoint Alignment to correct pincushion distortion by adjusting the image edge mid-points. See Figure 3-23. Figure 3-23. Image Alignment Controls You must enter a passcode to access the Calibration menu. Use the built-in test pattern when adjusting the image corners or midpoints. To access it, check the Test Pattern box in the Corner Alignment or Midpoint Alignment menu. Note Tip Top Left (x, y) Left Middle (x) Left/Right Middle (y)Right Middl e(x) Bottom Left (x, y)Top Right (x, y) Bottom Right (x, y) Top/Bottom Middle (x) Top Middle (y) Bottom Middle (y) Notes: 1. Smaller “x” values move a point to the left; larger values move it to the right. 2. Smaller “y” values move a point up; larger values move it down. Center (x, y)
Installation 54 LightStyle™ LS-12HBd Installation/Operation Manual PREL IMINARY 3.12 Installing and Adjusting the Anamorphic LensIf you are installing an LS-12HBd with an anamorphic lens, proceed as follows to install and adjust the lens. Attach the anamorphic lens to the bracket using the plastic knobs supplied with the lens. See Figure 3-24. Figure 3-24. Attaching the Anamorphic Lens to the Lens Mount Configure Lens Motor Trigger on Dimension Digital Controller: The anamorphic lens solution for the LS-12HBd maintains constant image height independent of the aspect ratio, while using the full display resolution of the projector. It accomplishes this by moving the anamorphic lens in front of the primary lens when widescreen material is being viewed. When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens moves out of the light path. Proceed as follows to configure the 12-volt trigger output for proper operation. 1. Project a 2.35:1 aspect ratio test pattern or other image on the screen. 2. On the Dimension Digital Controller remote control or front panel, press MENU. 3. Select Service from the Main Menu and enter the Service Menu passcode. 4. Select Tr i g g e rs from the Service menu. 5. Assign the trigger output to which the lens motor is connected to the Cinema and Virtual Cinema aspect ratios. This enables the lens motor to move the anamorphic lens into position (in front of the primary lens) when either aspect ratio is selected. It is extremely important that the primary lens is properly adjusted before you install the anamorphic lens. Ensure that the image from the primary lens is perfectly centered on the screen. Note You must enter a passcode to access the Service menu for the first time after turning on the system. Note