Roland VersaUV LEC 330 User Manual

5-3 Accommodating Various Kinds of Media
79Chapter 5 Feature Reference
Speeding Up Printing for Narrow Media
Procedure
Press.
Press
several times.
Press.
Press
several times.
Press.
Use
to select "SHEET" or "OFF."
Press
to enable the setting.
Press.
Press
to go back to the original screen.
Description
This  shortens  printing  time  by  reducing  the  width  of  the  print-head  movement  range  to  the  minimum  necessary. This  is 
effective when the width of the media or the...

5-3 Accommodating Various Kinds of Media 
80Chapter 5 Feature Reference
Preventing Soiling of the Media and Dot Drop-out During Printing
Procedure
Press.
Press
several times.
Press.
Press
several times.
Press.
Use
to select a value from "5 min" to "990 min," or 
"PAGE."
Press
to enable the setting.
Press.
Press
to go back to the original screen.
Description
Ink tends to collect on the surface of the heads when you use media prone to buildup of static charge, when the ambient...

5-3 Accommodating Various Kinds of Media
81Chapter 5 Feature Reference
2.Replace the short media clamps with the long ones. 
Remove the short media clamps.
Attach the long media clamps.
Description
When you want to hold the media in place more securely, such as when you're printing media that warps easily, use the long 
media clamps to secure the edges of the media in place. 
Note that when you're attaching the long media clamps, be sure to make the setting described above so that the media-...

5-3 Accommodating Various Kinds of Media 
82Chapter 5 Feature Reference
How to Load Sheet Media
To load and use sheet media, follow the steps below. 
1.Load the sheet media.
Measure the thickness of the sheet media.
If the measured value is 0.5 millimeters or more, increase the height of the print heads.
 P. 88, "Adjusting Head Height to Match Media Thickness"
Detach the rear cover.
If roll media is loaded, then remove it.
Remove both shafts.
Pass the sheet media through the machine....

5-3 Accommodating Various Kinds of Media
83Chapter 5 Feature Reference
Align the end of the sheet media with the location shown in the figure.
Pull back the loading lever.
The sheet media is secured in place. 
If you're performing printing, attach the media clamps.
However, if the thickness of the sheet media is 0.5 millimeters or more, leave the media clamps unattached. Otherwise 
the print heads may strike the media clamps, resulting in malfunction or other problems.
2.Make sure that media feed...

5-3 Accommodating Various Kinds of Media 
84Chapter 5 Feature Reference
Press and hold.
Hold down until the print-end position reaches the platen. 
For  media  that  passes  through  the  media  discharge  port  of  (1),  be  sure  to  comply  with  the  following.  Otherwise 
problems such as the print heads striking the sheet media may occur, resulting in malfunction or the like. 
 Never use the media clamps. 
 Increase the height of the print heads. 
 P. 88, "Adjusting Head Height to Match...

85Chapter 5 Feature Reference
5-4 Changing How the Printer Operates 
Executing Environment Matching Automatically 
Procedure
Press.
Press
several times.
Press.
Press
.
Press.
Use
to select "ENABLE."
Press
to enable the setting.
Press.
Press
to go back to the original screen.
Description
This setting enables or disables the feature for automatic adjustment to optimize the state of the machine to the environment 
where it is used (temperature and humidity). Performing automatic adjustment can...

5-4 Changing How the Printer Operates
86Chapter 5 Feature Reference
Default Setting 
[EMPTY MODE]: STOP
Setting the Interval until Activation of the Sleep Mode
Procedure
Press.
Press
several times.
Press.
Press
several times.
Presstwice.
Use
to make the setting.
Press
to enable the setting.
Press.
Press
to go back to the original screen.
Default Setting
[INTERVAL]: 30min
Deactivating the Sleep Mode
Procedure
Press.
Press
several times.
Press.
Press
several times.
Press.
Press
.
Press.
Use
to...

5-4 Changing How the Printer Operates
87Chapter 5 Feature Reference
Changing the Menu Language and the Units of Measurement 
Procedure
Hold downand switch on the sub power.
Use
to select the display (menu) language.
Press
.
Useto select the measurement unit for length.
Press
.
Useto select to the measurement unit for tempera-
ture.
Press
.
Description 
This sets the language and units of measurement displayed on the printer's screen.
Default Setting 
[MENU LANGUAGE]: ENGLISH
[LENGTH UNIT ]: mm...

88Chapter 5 Feature Reference
5-5 Optimizing Printing to Match Media Thickness
Adjusting Head Height to Match Media Thickness
Procedure
Press.
Press
several times.
Press.
Open the front cover.
Move the lever to adjust the height of the head.
Moving the lever to "HIGH" makes a warning beep sound twice. Moving it to "LOW" makes the warning beep sound 
once. 
Close the front cover.
The print heads return to their original position and the screen shown in the figure 
appears. 
Press....