Roland VersaUV LEC 330 User Manual

29Chapter 2  Basic Operation
2-2 Switching the Power On and Off
Switching the Power On and Off
This machine has a main power switch and a sub power switch. Switch on both to use the machine.
Whenever printing is finished, switch off the sub power. You also flip down the loading lever to the rear of the machine.
Leave the main power switch 
 on at all times, never switching it off. Leaving it on activates the alarm feature. 
 P. 72, "Alarm Feature"
Important Note on Switching Off the Power
Never...

2-2 Switching the Power On and Off
30Chapter 2  Basic Operation
The Power-saving Feature
This machine is provided with a power-saving feature that switches to a low-power "sleep mode" when a fixed interval passes 
with no operation. The factory default for the time after which the machine switches to the sleep mode is 30 minutes.
You can change the setting for the time of the shift to the sleep mode. You can also switch off the power-saving feature.
 P. 86, "Setting the Interval until...

31Chapter 2  Basic Operation
2-3 Loading and Cutting Off Media
Loading Media
Media may be of one of two types: media wound onto a paper tube (called “roll media”) and media not rolled in this way 
(called “sheet media”). This section explains how to load media, using roll media as an example. For information on how to 
load sheet media, refer to the page indicated below. 
 P. 82 "How to Load Sheet Media"
 CAUTION Load roll media correctly. 
Otherwise the media may fall and cause injury....

2-3 Loading and Cutting Off Media
32Chapter 2  Basic Operation
Detach the rear cover.
Place  the  roll  media  on  the  shafts  and  position  its  left  and  right  edges  to  match  the  grit 
patterns.
Secure the stoppers in place in alignment with the width of the media.
Make  sure  the  media  flanges  are  straight.  Correct  media  feed  is  impossible  if  either  of  the  media  flanges  is  at  an 
angle.
OKNot OK
 20 mm or more 20 mm or more
Be sure to ensure 
the media is within 
this...

2-3 Loading and Cutting Off Media
33Chapter 2  Basic Operation
Attach the rear cover.
Pass the leading edge of the media between the grit rollers and the pinch rollers, and feed 
it out as far as the platen.
Pinch rollerGrit rollerPlaten
Rear cover
Engage.
Engage.
Downloaded From ManualsPrinter.com Manuals 

2-3 Loading and Cutting Off Media
34Chapter 2  Basic Operation
Make sure both edges of the media are above the grit rollers, then place pinch rollers over 
all grit rollers covered by the media.
Placing the pinch rollers inside each of the grit patterns ensures that they are positioned above the grit rollers. 
Be sure to place the left and right pinch rollers at the edges of the media. The middle pinch rollers cannot be lowered 
at any position other than above the grit rollers. 
When positioning the...

2-3 Loading and Cutting Off Media
35Chapter 2  Basic Operation
2.Secure the media in place so that it is without slack.
Hold the media at the center and pull it out, being sure to keep it stra\
ight.
Make sure all areas of the media are taut.
Pull back the loading lever.
The media is secured in place. 
Loading lever
Downloaded From ManualsPrinter.com Manuals 

2-3 Loading and Cutting Off Media
36Chapter 2  Basic Operation
3.Clamp the edges of the media with the media clamp.
Move the media clamps as shown in the figure below.
Close the front cover.
Use  to select "ROLL."
Press 
.
Press .
SETUP SHEET
                            L 25.0  m
Left media clampsLine up the edge of the media with 
the centers of the holes. Right media clampsLine up the edge of the media with 
the centers of the holes.
Downloaded From ManualsPrinter.com Manuals 

2-3 Loading and Cutting Off Media
37Chapter 2  Basic Operation
Important Note When Using the Media Clamps
  Insert  the  media  clamps  firmly  all  the  way  until  they  engage  with  an  audible  click,  and  make  sure  they  will  not  come loose. Incorrect mounting may cause the media to catch or snag and make correct printing impossible, or may lead to 
malfunction or poor printing quality. 
 As printing proceeds, the media may move to the left or right and touch or come loose from the media...

2-3 Loading and Cutting Off Media
38Chapter 2  Basic Operation
Cutting Off the Media
Some media may be thick or may be composed of plastic or other hard material. For such media, never perform cutoff using 
. Doing so may cause malfunction or other problems. 
Procedure
Close the front cover.
Make sure
lights up.
Hold downfor one second or longer
The media is cut off.The cutoff location on the media is as shown in the figure below.
You  can  make  the  setting  in  the  software  RIP  for  automatic...