Roland VersaUV LEC 330 User Manual

4-4 Replacing Consumable Parts
69Chapter 4 Maintenance and Adjustment
3.Quit the blade replacement mode.
Close the front cover.
Press
.
Pressto go back to the original screen.
Replacing the Separating Knife
If the separating knife becomes dull, replace it with the included replacement knife.
 CAUTION Be sure to perform operations as specified by these instructions, and never touch 
any area not specified in the instructions.
Sudden movement of the machine may cause injury.
 CAUTION Never touch the tip...

4-4 Replacing Consumable Parts
70Chapter 4 Maintenance and Adjustment
2.Replace the separating knife.
Remove the separating knife.
 Loosen the screw until it slips out.
 Grasp the screw portion, and slowly pull it out in the direction of the arrow. When doing this, do not pull it back 
toward you.
Install a new knife.
The knife is secured in place by the magnet.
Slowly insert it into the groove.
Tighten the screw.
Take care to ensure that the knife does not slip out of position at this time.
3.Quit...

71Chapter 4 Maintenance and Adjustment
4-5 Adjustment of White Ink
Maintenance Tasks for White Ink
When white ink is used, dot drop-out or other problems that impede normal ink discharge may occur even when powerful 
cleaning  or  manual  cleaning  of  the  print  heads  has  been  performed.This  can  occur  because  the  ingredients  in  white  ink 
tend to settle, and may harden if allowed to stand for a lengthy time. If this happens, carry out the maintenance operations 
described below. 
These...

72Chapter 4 Maintenance and Adjustment
4-6 When Not in Use for a Prolonged Period
Keep Performing Maintenance
Switch on the power once every two weeks.
Switch on the sub power once every two weeks. When you turn on the power, the machine automatically performs some 
operations such as those to keep the print heads from drying out. Allowing the machine to stand completely unused for a 
prolonged period may damage the print heads, so be sure to switch on the power to perform these automatic operations....

73Chapter 4 Maintenance and Adjustment
4-7 When Moving the Unit 
Procedures from Preparing to Move Through Reinstalling 
To move the machine, you must completely drain all ink inside the machine and secure the print heads in place with pack-
ing materials to protect them. Attempting to move the machine without first doing this may result in damage to internal 
components due to leaking ink or damage to the heads. 
This operation requires four unused SOL INK cleaning cartridges. Have these on hand before...

4-7 When Moving the Unit
74Chapter 4 Maintenance and Adjustment
Detach the roll media from the media holders. 
Detach the media holders and the shafts. 
If necessary, also detach the dancer roller, rail slider, and stand legs etc. 
The machine is now ready to be moved. 
3.Immediately move the machine and fill it with ink. 
Once the preparations are complete, move the machine with as little dela\
y as possible. 
Immediately reinstall the machine and fill with ink. 
Referring to the Setup Guide,...

75
Chapter 5  
Feature Reference
Downloaded From ManualsPrinter.com Manuals 

76Chapter 5 Feature Reference
5-1 Pausing or Canceling Output
Canceling Output Before It Finishes
Procedure
Press .
 Hold down  for one second or longer.
 Stop sending output data from the computer.
Description
 pauses output. 
Pressing 
 a second time here resumes printing, but a horizontal stripe is produced at the location where printing 
was stopped. We do not recommend resuming printing.
Downloaded From ManualsPrinter.com Manuals 

77Chapter 5 Feature Reference
5-2 Setting the Print-start Position 
Setting the Print-start Position
Procedure
Use   to move the cutting carriage.
Align the center of the blade with the new print-start position.
 Press .
Description 
You can set the print-start position at any location you want. Note, however, that this setting returns to its default value after 
printing, and so it needs to be set separately for each page. When the start location has been set,
lights up and screen 
displays the...

78Chapter 5 Feature Reference
5-3 Accommodating Various Kinds of Media
Using Transparent Media
Procedure
Press .
Press 
 several times .
Press  twice.
Use 
 to select "DISABLE."
Press  to enable the setting.
The settings are changed and the screen shown in the figure appears. 
Description
This setting enables or disables detection of the leading and trailing edges of the media. It is normally set to "ENABLE." 
When transparent media is loaded, set it to "DISABLE." When this is...