Roland VersaUV LEC 330 User Manual

5-14 Menu List
11 9Chapter 5 Feature Reference
PRESET
NAME
NAME
_NAME
NAME3
NAME
NAME5
NAME
NAME7
NAME
NAME8
To the [NAME1] men u
To the [LO AD] menu
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
NAME
_
Continued
Contin ued
MENU
ADJUST BI-DIR
ADJUST BI-DIR
SIMPLE SETTING
ADJUST BI-DIR
DETAIL SETTING
ADJUST BI-DIR
TEST PRINT
SIMPLE SETTING
00
DETAIL SETTING
SETTING NO .1
DETAIL SETTING
TEST PRINT
T o the [DET AIL SETTING] men u
To the 
  [TEST PRINT] men u
To the [SETTING NO .4] menu
To the [TEST PRINT] men...

5-14 Menu List
120Chapter 5 Feature Reference
VACUUM POWER.
AUTO
SUB MENU
FA CT OR Y DEFA ULT
Continued Continued
INK CONTROL
EMPTY  MODE
SUB MENU
SLEEPSLEEP
INTERVAL
SLEEP
SETTINGSETTING
ENABLEENABLE
SUB MENU
SYSTEM REPORT
SUB MENU
INK CONTROLEMPTY  MODE
ST OPSTOP
INTERV AL
30min30min
To  the [SETTING] menu
To the [INTERV AL] menu
PERIODIC CL.
NONENONE
INK CONTROL
PUMP UP
INK CONTROL
HEAD W ASH
SUB MENU
PERIODIC CL.
MAINTENANCE
REPLACE WIPER
  To the [HEAD W ASH] menu
To  the [EMPTY  MODE] menu
FULL...

5-14 Menu List
121Chapter 5 Feature Reference
SYSTEM INFO .
MODEL
SYSTEM INFO .
INK
SYSTEM INFO .
FIRMWARE
Continued
MENU
SYSTEM INFO .MODEL
LEC-330
SYSTEM INFO .
SERIAL NO .SERIAL NO .
ZS00001
INK
ECO-UV    C M Y K Gl W
FIRMW ARE
V er .1.00
To the [NETW ORK] menu
To the [MODEL] men u
MENU
INK REMAINING
SHEET REMAIN
SET LENGTH
MENU
SHEET REMAINSHEET REMAIN
PRINT MEMO
SET LENGTH
0.0 m0.0 m
To the [A UTO DISPLA Y] menu
To the [PRINT MEMO] men u
SHEET REMAIN
AUT O DISPLA YAUT O DISPLA Y
DISABLEDISABLE
1...

5-14 Menu List
122Chapter 5 Feature Reference
CUTTING MENU
PRINT-CUT ADJ.PRINT-CUT ADJ.
TEST PRINT
Continued
MENU
CUTTING MENUTo  the [AU TO  ENV.  MATCH] menu
To the [TEST PRINT] menu
To the [TEST PRINT 2] menu
To the
 [PRESET] menu
F  :   +0.00        0.00 m
S  :   +0.00        0.00 m
CUTTING MENU
CALIBRA TION
To the [FEED SETTING] menu
To the [SCAN SETTING] menuFEED SETTING
0.00%
SCAN SETTING
0.00%
CUTTING MENU
PREFEED
CUTTING MENU
CUTTING PRIOR
PREFEED
DISABLE
CUTTING PRIOR
COMMAND
DISABLE
COMMAND...

5-14 Menu List
123Chapter 5 Feature Reference
Language and Unit Menu
Cleaning Menu
Cutting Configuration Menu
MENU LANGUAGE
ENGLISH
Hold do wn                        and s witch on the sub power.
LENGTH UNI T
mmmm
TEMP UNIT
 C C
CLEANING
NORMAL CL.
CLEANING
MEDIUM CL.
T o the [PO WERFUL CL.] men u
To the [NORMAL CL.] men u
NORMAL CL.
        ABC
MEDIUM CL.
        ABC
CLEANING
POWERFUL CL.POWERFUL CL.
        ABC
Press .Hold down                        f or one second or longer . 
Head cleaning for all...

124
Downloaded From ManualsPrinter.com Manuals 

125
Chapter 6  
What to Do If
Downloaded From ManualsPrinter.com Manuals 

126Chapter 6 What to Do If
specifies the IP address set on the machine, that the settings have 
no typing errors, and for other such problems.
 Setup Guide
 P. 112 "Setting the IP Address, Subnet Mask, Etc." 
Did the software RIP end abnormally? 
Make sure the software RIP is running correctly, then switch the 
sub power switch off and back on.
Is the temperature of the room too low?
Use the machine in an environment where the temperature is 
20 to 32˚C (68 to 90˚F).
The Media Take-up System...

127Chapter 6 What to Do If
Printed Results Are Coarse or Contain Horizontal Stripes
Do the print heads show dot drop-out?
Carry out a printing test and make sure no dot drop-out occurs. 
If dot drop-out is present, perform head cleaning.
 P. 40, "Printing Tests and Cleaning"
 P. 57, "When Head Cleaning Is Not Effective"
Is the head height appropriate? 
Printing when the [HEAD HEIGHT ] menu item is set to "HIGH" is 
coarser than when set to "LOW." Keep this set to...

6-2 Attractive Printing Is Impossible
128Chapter 6 What to Do If
S] and [PERIODIC CL.], uneven colors may occur. If the settings 
have been changed, try restoring them to their default values.
 P. 79, "Speeding Up Printing for Narrow Media"
 P.  80,  "Preventing  Soiling  of  the  Media  and  Dot  Drop-out  During 
Printing"
Is  the  printer  installed  in  a  level  and  stable  loca-
tion?
Never install the machine in a location where it is tilted or where 
it may wobble or experience...