Roland VersaUV LEC 330 User Manual

129Chapter 6 What to Do If
6-3 The Media Jams
The Media Jams
If an error message is displayed because the media 
has jammed, immediately correct the problem. Failure 
to do so may damage the print heads.
 P. 135, [MOTOR ERROR TURN POWER OFF]
Is the media warped or wrinkled?
Many  factors  can  cause  warping  or  wrinkling.  Refer  to  the  fol-
lowing and correct the problem.
 P. 131, "Media Wrinkles or Shrinks, or Feed Is Unstable"
Is the height of the print heads too low?
Try  raising  the...

130Chapter 6 What to Do If
6-4 The Media Cannot Be Taken Up Smoothly
The Media Cannot Be Taken Up Smoothly
Is media feed unstable?
Various factors can make media feed unstable. Refer to the fol-
lowing and correct the problem.
 P. 131, "Media Wrinkles or Shrinks, or Feed Is Unstable"
Is the paper tube installed correctly? 
Securely insert the paper tube onto the end caps. If the paper 
tube is not attached correctly, it may spin without traction and 
fail to take up the media. 
 Setup Guide
Is...

131Chapter 6 What to Do If
6-5 Media Wrinkles or Shrinks, or Feed Is Unstable
A  variety  of  problems  can  occur  if  the  media  feed  is 
not  smooth.  This  can  cause  such  problems  as  poor 
printing  quality,  contact  with  the  media  by  the  print 
heads,  misaligned  positioning,  or  media  jams.  Take 
action as follows.
Media Wrinkles or Shrinks
Is  the  media  loaded  and  set  up  straight  and  se-
curely?
Feed is not smooth when the media is not straight or is tensioned 
unevenly on...

132Chapter 6 What to Do If
If the print-head carriage stops over the platen, take 
action immediately to prevent the heads from drying 
out.
What to Do First
Switch  the  sub  power  off,  then  back  on  again.  (If  the  media  is 
jammed, then also remove the media.) If the print-head carriage 
move to the standby position (the right side of the main unit), it 
means the operation has ended successfully.
If  the  print-head  carriage  did  not  move,  try  switching  off  the 
main power, then again...

133Chapter 6 What to Do If
6-7 If a Message Appears
These  are  the  main  messages  that  appear  on  the 
machine's  display  to  prompt  correct  operation. They 
do not indicate any error. Follow the prompts and take 
action accordingly.
[1n 2n 3n 4n ...] 
Only a small amount of ink remains. Replace the cartridge indi-
cated by the flashing number with a new cartridge. 
[PRESS POWER KEY TO CLEAN] 
This  appears  when  the  machine  has  been  unused  for  about 
one month.
This feature is to...

134Chapter 6 What to Do If
6-8 If an Error Message Appears 
This  describes  the  error  messages  that  may  appear 
on  the  machine's  display,  and  how  to  take  action  to 
remedy  the  problem.  If  the  action  described  here 
does not correct the problem, or if an error message 
not described here appears, contact your authorized 
Roland DG Corp. dealer.
 [ALIGN POINT POSITION INVALID] 
An attempt was made to set an align point at a loca-
tion where the setting cannot be made.
No align...

6-8 If an Error Message Appears
135Chapter 6 What to Do If
Operation cannot be continued. Switch the sub power off, then 
back  on.  To  change  the  head  height,  use  the  [HEAD  HEIGHT ] 
menu. 
 P. 88, "Adjusting Head Height to Match Media Thickness" 
[TEMPERATURE IS TOO LOW **°C]
The temperature of the location where the machine 
is installed has fallen below the ambient temperature 
at which the machine can operate.
Operation cannot be continued. Switch off the sub power. The 
displayed...

136
Downloaded From ManualsPrinter.com Manuals 

137
Chapter 7  
Specifications
Downloaded From ManualsPrinter.com Manuals 

138Chapter 7 Specifications
7-1 Usable Media
Conditions for Usable Media
Media width
182 to 762 mm (7.2 to 30 inches)
A) Cuttable media thickness
0.08 to 0.22 mm (3.2 to 8.6 mil)
(depending on media composition)
B) Maximum media thickness (including backing paper)
Printing only: 1.0 mm (39 mil)
When performing cutting: 0.4 mm (15 mil)
C) Roll outer diameter 
Maximum 180 mm (7.1 inches)
D) Paper tube (core) inner diameter
50.8 mm or 76.2 mm (2 inches or 3 inches)
Roll weight
 20 kg (44 lb.)
Other...