Home > Ricoh > Printer > Ricoh Sp C410dn Service Manual

Ricoh Sp C410dn Service Manual

Here you can view all the pages of manual Ricoh Sp C410dn Service Manual. The Ricoh manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 81

Ethernet Configuration
69
4
Making Network Settings for Using Netware
If you use NetWare, select the frame type for NetWare.
Select one of the items below if necessary.
Auto Select
Ethernet II
 Ethernet 802.2
 Ethernet 802.3
 Ethernet SNAP
Important
❒Usually, use the default setting ([Auto Select]). When you first select [Auto Se-
lect], the frame type detected by the printer is adopted. If your network can
use more than two frame types, the printer may fail to select the correct frame
type if [Auto...

Page 82

Configuration
70
4
DSelect [NW Frame Type] using {T} or {U}, and then press the {OK} key.
ESelect the frame type using {T} or {U}, and then press the {OK} key.
FPress the {Menu} key to return to the initial screen.
GPrint a configuration page to confirm the settings made.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide. 

Page 83

IEEE 802.11b (Wireless LAN) Configuration
71
4 IEEE 802.11b (Wireless LAN) Configuration
Configure the printer to use IEEE 802.11b (Wireless LAN). The following table
shows the control panel settings and their default values. These items appear in
the [Host Interface] menu.
Note
❒To use IEEE 802.11b (Wireless LAN), select [IEEE 802.11b] for [LAN Type] in [Net-
work] in the [Host Interface] menu, and then set the IP Address, Subnet Mask,
Gateway Address, DHCP, Network Frame Type, and Effective Protocol...

Page 84

Configuration
72
4
CSelect [IEEE 802.11b] using {T} or {U}, and then press the {OK} key.
DSelect [Communication Mode] using {T} or {U}, and then press the {OK} key.
ESelect the transmission mode of IEEE 802.11b using {T} or {U}, and then
press the {OK} key.
The factory default is [802.11 Ad hoc].
 To use an IEEE 802.11b card for which the SSID (Network Name) setting is
not necessary, select [Ad hoc].
 The transmission mode of IEEE 802.11b can also be set using a Web brows-
er. For details, see Web...

Page 85

IEEE 802.11b (Wireless LAN) Configuration
73
4
ISet [Communication Speed] in the same way.
The factory default is [Auto Select]. If you need to change the transmitting
speed depending on environment you are using, select the appropriate trans-
mitting speed.
JPrint a configuration page to confirm the settings made.
Reference
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide.
Setting SSID
If [Infrastructure] or [802.11 Ad hoc] is selected for [Communication...

Page 86

Configuration
74
4
Reference
SSID can also be set using a Web browser. For details, see the Web Image
Monitor Help, and “Configuring the Network Interface Board Using Web
Browser”, Software Guide.
WEP key can also be set using a Web browser. For details, see Web Image
Monitor Help.
For details about printing the configuration page, see “Test Printing”,
Quick Installation Guide.
Setting a WEP key
In the case of using a WEP key on a network, activate the WEP setting to be used
for communication along with...

Page 87

IEEE 802.11b (Wireless LAN) Configuration
75
4
DEnter the characters using {V}, or {W}, and then press the {OK} key.
You can switch among upper/lower cases, numeric codes, and symbols by
pressing [ABC/123].
When using 64 bit WEP, up to 10 characters can be used for hexadecimal and
up to five characters for ASCII. When using 128 bit WEP, up to 26 characters
can be used for hexadecimal and up to 13 characters for ASCII.
The number of characters that can be entered is limited to 10 or 26 for hexa-
decimal...

Page 88

Configuration
76
4 

Page 89

77
5. Paper and Other Media
Paper and Other Media Supported by This 
Printer
This section describes the paper size, feed direction, and the maximum amount
of paper that can be loaded into each paper tray in this printer.
Note
❒The following symbols and terminology are used to represent the feed direction.
❒Be careful of the paper feed direction. The direction is determined for each paper
size.
❖Input Paper Sizes (Metric version)
In this manual On the display Paper feed direction
K ↑ (Feed direction)A4
8...

Page 90

Paper and Other Media
78
5
*1The size cannot be set automatically if you use the following model: *2The size cannot be set automatically if you use the following model: 
 
The size is supported and the printer selects it automatically.

The size is supported, but it should be selected using the control panel.

The size is supported, but it should be set as a custom size using the control
panel.
The supported size may differ depending on the printer language you use.
Set as a custom size setting using...
Start reading Ricoh Sp C410dn Service Manual

Related Manuals for Ricoh Sp C410dn Service Manual

All Ricoh manuals