Ricoh Sp C410dn Service Manual

Replacing the Photo Conductor Unit
109
6 Replacing the Photo Conductor Unit
The following procedure describes replacing the first photo conductor unit from
the right. The procedure is the same for all four photo conductor units.
❖When to replace the photo conductor unit
Replace the photo conductor unit if the following messages appear:
 “Replace PCU:Black.”
Replace the black photo conductor unit.
 “Replace PCU:Colour.”
Replace the three color photo conductor units.
The color photo conductor units...

Replacing Consumables and Maintenance Kit
110
6
CTurn the two green levers counterclockwise ( ), and then slowly open the
inner cover ( ).
The photo conductor units are installed as shown. From the right, the units
are attached in the order of black (K), magenta (M), cyan (C), and yellow (Y).
DRemove the photo conductor unit you want to replace. Turn the green lever
counterclockwise to unlock the unit. (The black photo conductor unit is
used in this example.)
AQC013S
AET137S
AET138S 

Replacing the Photo Conductor Unit
111
6
EPull out the ring pull handle of the photo conductor unit.
FHook your finger through the ring pull handle, and then slowly pull out
the photo conductor unit. When you have pulled the unit half way out, sup-
port the photo conductor unit using your other hand, and then pull the unit
completely out.
 Do not hold any protruding areas of the photo conductor unit. Doing so
may break the photo conductor unit.
 Do not touch any protruding areas of the photo conductor...

Replacing Consumables and Maintenance Kit
112
6
HRemove the protecting cover. Do not remove the tape yet.
ICheck the installation position of the photo conductor unit. Install the unit
where the colored labels correspond.
JInstall the photo conductor unit with the tape still attached. Align the tip of
the photo conductor unit with the opening, and then slowly insert the unit,
until it stops.
Take care that nothing comes into contact with the surface of the photo con-
ductor unit.
AET142S
AQC71S
AET143S 

Replacing the Photo Conductor Unit
113
6
KUse a finger to push the label with three green lines, and then push in the
photo conductor unit, until it clicks into position. If the installation fails,
the small, pentagonal window turns red.
LHold the photo conductor unit firmly in place, and then pull out the tape.
 Remember to pull out the tape. Malfunctions occur if you attempt to print
while the tape is still attached.
 The removed tape is dirty. Be careful not to let it touch your hands or
clothes....

Replacing Consumables and Maintenance Kit
114
6
NClose the inner cover. Lock the inner cover by pressing in ( ) and then
turning the two green levers clockwise ( ).
OCarefully close the left cover.
PPlug in the power cable, and then turn on the power.
The printer starts calibration. Wait until it stops.
Wait until “Ready” appears on the display panel.
Do not turn off the power during calibration. Doing so results in malfunction.
AQC014S 

Replacing the Intermediate Transfer Unit
115
6 Replacing the Intermediate Transfer Unit
R CAUTION:
❖When to replace the transfer unit
 Replace the transfer unit if the following message appears on the display: 
“Replace IntTrans Unit.”
ATurn off the power, and then unplug the power cable.
BCarefully open the left cover of the printer.
CTurn the two green levers of the inner cover anticlockwise ( ), and then
slowly open the inner cover ( ). The inside of this printer becomes very hot. Do not touch parts...

Replacing Consumables and Maintenance Kit
116
6
DCarefully open the printers front cover (A) by pulling the left and right
side levers.
ETurn the green lever of the transfer unit counterclockwise to unlock the unit.
FPull out the handle of the transfer unit. Grasp the handle and the green le-
ver firmly, and then slowly pull out the transfer unit, until the green line
marked on the upper surface of the unit appears.
Do not touch any protruding areas on the transfer unit. These may stain your
hands or...

Replacing the Intermediate Transfer Unit
117
6
GWhen the green line appears, pull up the handles on the upper surface and
support the transfer unit with your other hand.
HGrasp the raised up handles with both hands, and then pull the transfer
unit completely out.
 Use both hands and both handles when you pull out the unit.
 Do not touch the belt area (underside) of the unit.
ITake the new transfer unit out of its box.
AET950S
AET951S
AET952S 

Replacing Consumables and Maintenance Kit
118
6
JHold both upper handles, and then slide the transfer unit along the guide
rails into the printer.
The upper handles must be raised to insert the unit.
KWhen the upper handles touch the printer body, lower the handles, and
then push in the transfer unit, until it stops.
LTurn the green lever clockwise to lock the unit.
MCarefully close the front cover (A).
AET953S
AET954S
AET146S