Ricoh Sp C410dn Service Manual

Paper and Other Media Supported by This Printer
79
5
❖Input Paper Sizes (Inch version)
 
The size is supported and the printer selects it automatically.

The size is supported, but it should be selected using the control panel.

The size is supported, but it should be set as a custom size using the control
panel.
The supported size may differ depending on the printer language you use.
Set as a custom size setting using the control panel.
The following sizes are supported:
Feed direction
Size (inch)...

Paper and Other Media
80
5
 Tray 1: approximately 3.94 - 8.5 inches in width, and 5.83 - 14 inches in
length. 
 Bypass Tray: approximately 2.76 - 8.5 inches in width, and 5.83 - 35.43
inches in length. 
 Paper Feed Unit (Tray 2/3): approximately 3.94 - 8.5 inches in width,
and 8.27 - 14 inches in length. 
 
The size is not supported.
❖Paper weight and number of sheets to be set
Check that the top of the stack is not higher than the limit mark inside the
tray.
Supported paper weightMaximum number of...

Paper Recommendations
81
5 Paper Recommendations
Loading Paper
Important
❒Do not use ink-jet printer paper because it may stick to the fusing unit and
cause a paper misfeed.
❒When printing on OHP transparencies that have a print side, load them with
the print side over on the bypass tray. Not taking this precaution may cause
them to stick to the fusing unit and cause misfeeds.
❒Set the paper as described below
 Tray 1: Print side facing up
 Bypass Tray: Print side facing down
 Paper Feed Unit (Tray 2,...

Paper and Other Media
82
5
Types of Paper and Other Media
Plain Paper
Letterhead
Note
❒If the printing result is badly wet or smudged, change the setting on the print-
ers control panel as the following:
Press the {Menu} key, select [Maintenance], [General Settings], and then select
[Letterhead]. Select one from [Letterhead 1], [Letterhead 2], or [Letterhead 3].
The greater number corresponds to the thicker setting.
The one of these items is normally detected automatically according to the
paper type...

Paper Recommendations
83
5
Glossy Paper
Note
❒If the printing result is badly wet or smudged, change the setting on the print-
ers control panel as the following:
Press the {Menu} key, select [Maintenance], [General Settings], and then select
[Glossy Paper]. Select one from [Glossy Paper 1], [Glossy Paper 2], [Glossy Paper
3], or [Glossy Paper 4].
The greater number corresponds to the thicker setting.
The one of these items is normally detected automatically according to the
paper type you set. It is...

Paper and Other Media
84
5
Thick Paper
Thin Paper
Paper thickness
[Thick Paper]: 104.7 - 216 g/m2 (28 - 58 lb.)
[Thick Paper 1]: 104.7 - 157 g/m
2 (28 - 42 lb.)
[Thick Paper 2]: 157 - 216 g/m
2 (42 - 58 lb.)
Printer setup Make the following settings using the control panel:
 Press the {Menu} key, select [Paper Input] , and then select one 
from [Thick Paper], [Thick Paper 1] or [Thick Paper 2] for the selected 
trays paper type.
Printer driver setup Click [Thick 1] or [Thick 2] in the [Paper type:]...

Paper Recommendations
85
5
Label Paper
Note
❒If the printing result is badly wet or smudged, change the setting on the print-
ers control panel as the following:
Press the {Menu} key, select [Maintenance], [General Settings], and then select
[Label Paper]. Select one from [Label Paper 1], [Label Paper 2], or [Label Paper 3].
The greater number corresponds to the thicker setting.
The one of these items is normally detected automatically according to the
paper type you set. It is not necessary to change...

Paper and Other Media
86
5
Envelopes
Note
❒If the printing result is badly wet or smudged, change the setting on the printers
control panel as the following:
Press the {Menu} key, select [Maintenance], [General Settings], and then select
[Envelope]. Select one from [Envelope 1], [Envelope 2], [Envelope 3], or [Enve-
lope 4].
The greater number corresponds to the thicker setting.
The one of these items is normally detected automatically according to the pa-
per type you set. It is not necessary to change...

Paper Recommendations
87
5
Paper not supported by this printer
Avoid using the following paper as they are not supported by this printer.
 Paper meant for an ink-jet printer
 Bent, folded, or creased paper
 Curled or twisted paper
 Torn paper
 Wrinkled paper
 Damp paper
 Paper that is dry enough to emit static electricity
 Paper that has already been printed onto, except a preprinted letterhead.
Malfunctions are especially likely when using paper printed on by other than
a laser printer (e.g....

Paper and Other Media
88
5
Print Area
The following shows the print area for this printer. Be sure to set the print margins
correctly by the application.
❖Paper
APrint area
BFeed direction
CApprox. 4.2 mm (0.17 inches)
DApprox. 4.2 mm (0.17 inches)
Note
❒The print area may vary depending on the paper size, printer language
and printer driver settings.
❖Envelope
APrint area
BFeed direction
CApprox. 4.2 mm (0.17 inches)
DApprox. 4.2 mm (0.17 inches)
Note
❒The print area may vary depending on the paper...