Ricoh Sp C410dn Service Manual

Attaching Hard Disk Drive Type 4000
29
2
DGrasp the handles, and then pull the controller board carefully out.
Using both hands, slide the controller board completely out.
EPlace the controller board on a flat surface, and then loosen the four screws
to remove the cover.
The screws cannot be fully removed.
AQC640S
AQC650S
AQC660S 

Installing Options
30
2
FBe sure to install the hard disk drive unit as shown.
GUse the screws supplied with the hard disk drive to secure the unit to the
controller board.
HConnect the power cable to the hard disk drive and controller board.
AET069S
AET087S
AET088S 

Attaching Hard Disk Drive Type 4000
31
2
IConnect the flat cable to the hard disk drive and the controller board. Con-
nect the blue end of the flat cable to the controller board.
JWhen installing other options on the controller board, do not close the con-
troller board, but go to the steps for installing the option.
KFasten the four screws to attach the cover.
LAlign the controller board with the left and right rails, and then push it
carefully in, until it stops.
Push only on the area of the...

Installing Options
32
2
MFasten the controller board to the printer using the three screws.
When the power is turned on, the hard disk drive will be formatted automat-
ically.
Note
❒After finishing installation, you can check whether the hard disk drive is
properly installed: Print the configuration page from the [List/Test Print]
menu. If it is installed properly, “Hard Disk Drive” will appear for “Device
Connection” on the configuration page.
❒If the hard disk drive is not installed properly, reinstall...

Attaching IEEE 802.11b Interface Unit
33
2 Attaching IEEE 802.11b Interface Unit
R CAUTION:
Important
❒Before touching the 802.11b interface unit, touch something metal to dis-
charge any static electricity. Static electricity can damage the 802.11b interface
unit.
❒Do not subject the 802.11b interface unit to physical shocks.
ACheck the contents of the package for the following:
❖ IEEE 802.11b Interface Unit 
 Interface Unit
Card
 Antenna Do not touch the inside of the controller board compartment....

Installing Options
34
2
 Antenna Cap
BTurn off the power, and then unplug the power cable.
CLoosen the two screws and remove the cover of the 802.11b interface unit
installation unit.
The removed cover is not used when installing the interface unit.
DFully insert the 802.11b interface unit.
ETighten the two screws to secure the interface unit.
AAL888S
AQC091S
AET094S
AQC095S 

Attaching IEEE 802.11b Interface Unit
35
2
FAttach the antenna to the card with the label facing down and the uneven
side of the antenna facing up.
GWith the antenna and the indented end toward you, slowly insert the inter-
face card until it stops.
HHold the antenna cap with the cut off corners towards you and fit it over the card.
Note
❒After finishing installation, you can check the 802.11b interface unit is
properly installed: Print the configuration page from the [List/Test Print]
menu. If it is...

Installing Options
36
2Attaching Bluetooth Interface Unit Type 3245
R CAUTION:
Important
❒When using the printer with the Bluetooth interface unit installed, Bluetooth
needs to be installed on the computer.
❒Before manipulating the Bluetooth interface unit, touch something metal to
discharge static electricity. Static electricity thing damage the Bluetooth inter-
face unit.
❒Do not subject the Bluetooth interface unit to physical shocks.
ACheck the contents of the package for the following:
❖ Bluetooth...

Attaching Bluetooth Interface Unit Type 3245
37
2
 Antenna Cap
BTurn off the power, and then unplug the power cable.
CLoosen the two screws and remove the cover of the Bluetooth interface unit
installation unit.
The removed cover is not used when installing the interface unit.
DFully insert the Bluetooth interface unit.
ETighten the two screws to secure the interface unit.
AAL888S
AQC091S
AET094S
AQC095S 

Installing Options
38
2
FWith the “INSERT” side facing you, slowly insert the card into the Blue-
tooth interface unit until it stops.
GPress the antenna to extend it.
HHolding the antenna cap with the two cut-off corners toward you, fit the
cap over the card.
Note
❒After finishing installation, you can check the Bluetooth interface unit is
properly installed: Print the configuration page from the [List/Test Print]
menu. If it is installed properly, “Bluetooth” will appear for “Device Con-
nection” on...