Ricoh Sp C410dn Service Manual

9
2. Installing Options
Available Options
This section describes how to install options.
By installing options, you can improve the printer performance and have an ex-
panded variety of features to use. For the specifications of each option, see p.182
“Specifications”.
R CAUTION:
Important
❒The voltage rating of the connector for options is 24 V DC or less.
Option List
The following is a list of options for this printer.•Before installing options, the machine should be turned off and unplugged 
for at...

Installing Options
10
2
Option Installation Flow Chart
Installing multiple options in the following order is recommended:
AAttach the paper feed unit (Paper Feed Unit Type 4000).
Attach the paper feed units to the bottom of the printer.
You can attach up to two paper feed units. Up to 1750 sheets of paper can be
loaded in total.
BInstall the SDRAM module (Memory Unit Type D 128MB, Memory Unit
Type E 256MB).
Install the module to the SDRAM module slot on the controller board.
There are two types of memory...

Available Options
11
2
Installing Options
Install options in the positions shown in the illustration.
❖Exterior
1. Paper Feed Unit Type 4000 
Loads up to 550 sheets of paper. 
Up to two paper feed units, can be in-
stalled on the printer. Installed tray
units are identified as “Tray 2” and
“Tray 3”.
See p.14 “Attaching Paper Feed Unit
Type 4000”.
AET061S 

Installing Options
12
2
❖Interior
1.Memory Unit Type D 128MB/Mem-
ory Unit Type E 256MB (SDRAM mod-
ule)
Install 128 MB or 256 MB SDRAM
module into the controller board slot.
See p.17 “Attaching Memory Unit
Type D 128MB, Memory Unit Type E
256MB (SDRAM Module)”.
2.Optional boards
See p.33 “Attaching IEEE 802.11b In-
terface Unit”.
See p.36 “Attaching Bluetooth Inter-
face Unit Type 3245”.
See p.39 “Attaching IEEE 1284 Inter-
face Board Type A”.
See p.41 “Attaching the USB Host In-
terface Board Type A”....

Available Options
13
2
Caution when re-installing the controller board
This section describes handling the controller board when installing options.
If you slide out the controller board to install the SDRAM module, the user ac-
count enhance unit, or the printer hard disk, carefully follow the instruction be-
low to re-install the controller board.
 Re-install the controller board into the printer by pushing the bottom center
area of the board, as shown in the illustration.
Important
❒The following may...

Installing Options
14
2Attaching Paper Feed Unit Type 4000
When installing multiple options, install the paper feed unit first.
R CAUTION:
R CAUTION:
Important
❒Up to two paper feed units can be attached to the printer.
❒When two paper feed units are installed, they are detected as “Tray 2” and
“Tray 3” starting from the upper unit.
❒Before using the new paper feed unit, you must make settings in the printer
driver.
❒Check the printer nameplate to confirm the model code.
ACheck the package contains the...

Attaching Paper Feed Unit Type 4000
15
2
DLift the printer using the inset grips on both sides of the printer.
Important
❒The printer should always be lifted by at least two people.
EAlign the printer with the two upright pins on the paper feed unit and then
lower the printer slowly.
When installing two paper feed units, connect the two units first using the
same procedure below before connecting the units to the printer.
AQC031S
AET074S
AET075S 

Installing Options
16
2
Note
❒When moving the printer, remove the paper feed unit.
❒After finishing installation, you can check whether the paper feed unit is
properly installed: Print the configuration page from the [List/Test Print]
menu. If it is installed properly, “Tray 2” or “Tray 2”, “Tray 3” will appear
for “Connection Equipment” on the configuration page.
❒If the paper feed unit is not installed properly, reinstall it following this
procedure. If you cannot install it properly even after...

Attaching Memory Unit Type D 128MB, Memory Unit Type E 256MB (SDRAM Module)
17
2 Attaching Memory Unit Type D 128MB, 
Memory Unit Type E 256MB (SDRAM Module)
R CAUTION:
Important
❒Before touching the memory unit, ground yourself by touching something
metal to discharge any static electricity. Static electricity can damage the
memory unit.
❒Do not subject the memory unit to physical shocks.
❒Available memory varies depending on a model type.
❒Before using the new memory unit, Be sure to make settings in...

Installing Options
18
2
CGrasp the handles and carefully pull out the controller board.
Using both hands, slide the controller board completely out.
DPlace the controller board on a flat surface, and then loosen the four screws
to remove the cover.
The screws cannot be fully removed.
AQC640S
AQC650S
AQC660S