Ricoh Mp C6502 User Guide

• The default of [Printer Bypass Paper Size] is [Auto Detect].
Specifying regular sizes using the control panel
1. Press the [User Tools/Counter] key.
2.Press [Tray Paper Settings].
3. Press [Printer Bypass Paper Size].
4. Select the paper size.
5.Press [OK].
6. Press the [User Tools/Counter] key.
Loading Paper into the Bypass Tray
131CUP009   

Specifying a custom size paper using the control panel
1.Press the [User Tools/Counter] key.
2. Press [Tray Paper Settings].
3. Press [Printer Bypass Paper Size].
4. Press [Custom Size].
If a custom size is already specified, press [Change Size].
5. Press [Vertical].
6. Enter the vertical size using the number keys, and then press [
].
7.Press [Horizontal].
8. Enter the horizontal size using the number keys, and then press [
].
9. Press [OK] twice.
10. Press the [User Tools/Counter] key.
Specifying thick...

• Usually only one side of OHP transparencies can be used for printing. Be sure to load them with theprint side up.
• When printing onto OHP transparencies, remove printed sheets one by one.
1. Press the [User Tools/Counter] key.
2.Press [Tray Paper Settings].
3. Press [Printer Bypass Paper Size], and then specify the paper size.
4. Press [OK].
5. Press [
Next].
6. Press [Paper Type: Bypass Tray].
7. Select the proper items, according to the paper type you want to specify.
• Press [OHP (Transparency)] on...

• For details about paper thickness, see "Tray Paper Settings", Connecting the Machine/ SystemSettings
.
9. Adding Paper and Toner
134   

Loading Paper into the Large Capacity Tray
(mainly Europe and Asia)
The LCT can hold A4
 paper only. If you want to print on 8 1
/ 2 × 11 or B5 JIS from the LCT, contact
your service representative.
(mainly North America)
The LCT can hold 8 1
/ 2 × 11
 paper only. If you want to print on A4 or B5 JIS from the LCT, contact
your service representative.
The extension unit is required to load A4
, B4 JIS, 8 1
/ 2 × 14, or 8 1
/ 2 × 11.
• Check the paper edges are aligned at the left side.
1. Check that paper...

4.Load paper by repeating steps 2 and 3.
5. Close the top cover of the LCT.
9. Adding Paper and Toner
136CVA063   

Loading Paper into the Wide Large Capacity
Tray
• Check that the paper edges are aligned with the left side.
1. Check that paper in the paper tray is not being used, and then pull the tray carefully out
until it stops.
2. Load paper into the paper tray with print side up.
Do not stack paper over the limit mark.
3. Carefully push the paper tray fully in.
• If you select Thick Paper 2 to 4, [Coated Paper], [Label Paper], or [OHP (Transparency)] in [Tray
Paper Settings], air is blown out automatically to...

• You can load envelopes in the wide LCT. When loading envelopes, place them in the correctorientation. For details, see page 159 "Envelopes".9. Adding Paper and Toner
138  

Loading Paper into the Interposer
• Do not place anything on top of or leave documents on the sensor. This may lead to the paper sizenot being correctly scanned or paper jams.
• When using the Z-fold function, the paper in the interposer must be of the same size as the prints after they have been folded. If the paper in the interposer is larger than the Z-folded sheets, a
misfeed might occur.
1. Load paper orderly.
Do not stack paper over the limit mark.
2. Adjust the side fences to the paper size.
•...

InterposerADF9. Adding Paper and Toner
140