Ricoh Mp C4500 Service Manual

							103
7. Clearing Misfeeds
This chapter explains what to do when paper or originals misfeed (become
jammed inside the machine).
Removing Jammed Paper
R CAUTION:
R CAUTION:
Important
❒When clearing misfeeds, do not turn off the operation switch. If you do, your
copy settings will be lost.
❒To prevent misfeeds, do not leave any torn scraps of paper inside the ma-
chine.
❒Contact your service representative if misfeeds occur frequently.
Note
❒For details about how to locate and remove misfeeds, see “Checking Jammed
Paper” or “Removing Jammed Paper”.
Reference
p.104 “Locating Jammed Paper”.
p.105 “Removing Jammed Paper”. The fusing section of this machine might be very hot. Caution should be tak-
en when removing misfed paper.
Keep your hands clear of the booklet finisher tray when pulling out or push-
ing in the finishers staple unit. You can trap your fingers if you do not. 
						

							Clearing Misfeeds
104
7
Locating Jammed Paper
If a misfeed happens, remove the misfed paper or original following the proce-
dures stated on the sticker on the rear of main unit front cover.
A misfeed has occurred in the place corresponding to the letter displayed on the
control panel.
APress the key of the section from where you want to remove the jammed paper. 
BAfter each step is complete, press [Next]. To go back to the previous step,
press [Previous].
AQD024S 
						

							Removing Jammed Paper
105
7
CWhen all jammed paper are removed, restore the machine to the original
state.
Note
❒More than one misfeed may be indicated. When this happens, check all the
areas indicated.
Removing Jammed Paper
The following procedure explains how to remove jammed paper.
Important
❒The internal parts of the machine may be hot. Wait for the duplex unit to cool
down before clearing a paper jam in the unit.
When A is lit
When B is lit
AQE009S
AQE010S 
						

							Clearing Misfeeds
106
7
 When C is lit
 When D is lit
AQE011S
AQE012S 
						

							Removing Jammed Paper
107
7
 When P is lit (when ADF is installed)
 When R is lit (when SR790 is installed)
AQE013S
AQE014S 
						

							Clearing Misfeeds
108
7
 When R1 - R8 is lit (when Finisher SR3030 is installed)
AQE015S 
						

							Removing Jammed Paper
109
7
 When R1 - R12 is lit (when Booklet Finisher SR3020 is installed)
AQE016S 
						

							Clearing Misfeeds
110
7
 When Y is lit (when Wide Large Capacity Tray is installed)
 When Z1 is lit
Note
❒Inside the finisher, or inside the front cover, there is a sticker explaining how
to remove misfed paper.
❒If a detailed removal instruction appears on the right of the screen, follow it.
❒You can also use the procedure indicated in [System Status] to remove jammed paper.
AQE017S
AQE018S
AQE020S 
						

							Removing Jammed Staples
111
7 Removing Jammed Staples
This section explains how to remove jammed staples.
R CAUTION:
Important
❒Curled paper may cause staples to jam. To avoid this, turn copy paper over
in the tray.
❒When the finisher is installed, after removing jammed staples, staples will not
be ejected the first few times you try to use the stapler.
Remove the jammed staples according to the finisher type. (Check the type if
you are unsure.) For details about type of finisher, see “Options”, About This
Machine.
SR790
The following procedure explains how to remove jammed staples from the
SR790.Keep your hands clear of the booklet finisher tray when pulling out or push-
ing in the finishers staple unit. You can trap your fingers if you do not.
AQE903S 
						

							Clearing Misfeeds
112
7
Finisher SR3030 and Booklet Finisher SR3020
The following procedure explains how to remove jammed staples from the Fin-
isher SR3030 and Booklet Finisher SR3020.
AQE007S