Ricoh Mp C3000 Service Manual

  
SM 1-99 B230/B237/D042 
Installation 
 
9.  Touch the keys in the following order, to configure the minimum setup. 
  
1) “Server Setup ” key 
2) “ Main Menu/Cancel ” key 
3) (When you see “Save Changes for Server Setup / YES”)   
“OK ” key 
4) “ Network Setup ” key 
5) “ Exit Network ” key 
6) (When you see “Save Changes for Server Setup/ YES”)   
“OK ” key 
7) “ Printer Setup ” key 
8) “ Main Menu/Cancel ” key 
9) (When you see “Save Changes for Printer Setup / YES”)   
“OK ” key 
10. Select “Exit...

 
B230/B237/D042 1-100 SM 
 
1.22.11 VERIFYING THE CONNECT
ION (LOCAL TEST PRINT) 
After you connect the Color Controller to  the copier, print the Test Page and the 
Configuration Page to verify that t he connection between the Color Controller 
and the copier is good. 
1.  Make sure that the  copier is not in use. 
2.  Check the settings in the following table, and make sure that Letter or A4  paper is loaded in at least one of  the paper trays of the copier. 
 
 PS Setting 
Default Paper Size  PCL...

  
SM 1-101 B230/B237/D042 
Installation 
1.22.12  VERIFYING CONNECTION TO THE NETWORK 
The Color Controller provides twisted pair connectivity to an Ethernet network. 
Cable requirements: 
•  10BaseT (Ethernet): Unshielded T wisted Pair (UTP), Category 3 or 
higher 
•  100BaseTX (Fast Ethernet): UTP, Ca tegory 5 or higher (4-pair/8-wire, 
short length) 
•  1000BaseT (Gigabit Ethernet): UTP, Category 5e or higher  (4-pair/8-wire, 
short-length) 
NOTE:  If the print engine is 230V, us e a shielded network...

 
B230/B237/D042 1-102 SM 
 
NOTE: It is the site administrator’s res ponsibility to configure the correct 
setup options for the network  and user environment. The default 
settings in the setup may be adequate, but they may not be optimal 
for the user’s environment. Refer  the site administrator to the 
Configuration and Setup manual  for setup information. 
7.  After configuring the Setup optio ns, verify the network connection. 
Ask the site administrator to install the printer driver on a client...

  
SM 1-103 B230/B237/D042 
Installation 
1.22.13 INSTALLING OPTIONAL FEATURES 
Overview 
The system software for the Color Contro ller contains the following optional 
features: 
•  EFI Hot Folders  •  EFI Auto Trap •  EFI Spot On 
Initially, the above three optional functi ons cannot be used. When the customer 
purchases these options, a hardware U SB dongle which includes a license for 
the optional featur e will be provided. 
After the license for the feature is transfe rred to the Color Controller,...

 
B230/B237/D042 1-104 SM 
 
The number of times the license can be removed from the Color Controller is 
limited as shown in the table below. (Act ivate 4 times and deactivate 3 times.) 
When this limit is reached, the dongle c an no longer be used to remove the 
license, so the license will st ay on the Color Controller. If a dongle is inserted to 
remove a feature but the limit has  been reached, there will be no effect. 
Color Controller Power 
Turned On (or  Color 
Controller  Rebooted) with 
Dongle...

  
SM 1-105 B230/B237/D042 
Installation 
 
3.  Shut down the Color Controller and turn the power of the Color Controller 
OFF. ( 
 G889 SM Section 2.1.3) 
4.  Insert the dongle in the left USB port.    (There are three USB ports in the back p anel of the Color Controller. Insert 
the dongle to the left USB port.) 
5.  Make sure that the copier  main power is already ON. 
6.  Turn the power switch of the Color Controller ON. 
7.  Wait for the Color Controller to come to the idle status.  During this...

 
B230/B237/D042 1-106 SM 
If you have activated an optional feature, keep the configuration sheet. You 
may need it later for troubleshooting pur poses, as shown in the following 
caution. 
 
 
After an optional feature has been  activated, the optional feature license 
information is kept inside the ACT ch ip on the video board of the Color 
Controller.  
If the ACT chip becomes defective, the  following are needed as evidence in 
order to get a new ACT chip and optional feature dongle: 
• The...

 
PREVENTIVE MAINTENANCE 
SECTION 2  PREVENTIVE MAINTENANCE REVISION HISTORY 
Page Date  Added/Updated/New 
2    03/30/2007  PM Parts