Ricoh Mp C3000 Service Manual

  
SM 1-89 B230/B237/D042 
Installation 
1.22.5 INSTALLATION FLOW CHART 
Recommended installation steps are as follows: 
 
G889V900.WMF
Make sure that the copier
  is ready to use.
Unpack the E-3000
Connect the E-3000to the copie
r
Print Test Pages and aConfiguration Page
The site administrator connects
the E-3000 to the network and verifies the connections.
The site administrator installs user
software on networked computers that print to the E-3000.
Finished
Select the language and
do the minimum...

 
B230/B237/D042 1-90 SM 
1.22.6 MACHINE INSTALLATION 
Setting Customer Expectations 
Before installation, the customer should be informed of the following: 
•  Some nodes on the network may  be unavailable for up to one hour. 
•  The copier may be unavailable for up to one hour 
•  The site administrator should be avail able during the installation for network 
connectivity. 
•  Equipment downtime and im pact on the network can be minimized if the site 
administrator installs a network c onnector for...

  
SM 1-91 B230/B237/D042 
Installation 
1.22.7 UNPACKING THE COLOR CONTROLLER 
1.  Open the box and remove the packing material. 
2.  Remove the contents from the top container. Inspect  the contents for visible 
damage. The top container should  include the following items: 
3.  Give the Media Pack [F] to the site administrator. 
4.  Take the remaining component s out of the top container. 
5.  Remove the top container  and any packing materials. 
6.  Carefully lift the Colo r Controller out of the...

 
B230/B237/D042 1-92 SM 
1.22.8  FRONT AND BACK PANELS 
After unpacking the Color Controller, familiarize yourself with the front and back 
panels before you connect the Color Controller to the copier. 
•  Front Panel 
 
• Back Panel  
 
ON12ON12
 
G815R002A.WMF
A  Diagnostic LEDs (for service use only) 
B  Service Switches  (f or service use only) 
C Video Interface 
D Power Connector 
E Power Switch 
F Not Used 
G RJ-45 Connector 
 (10BaseT/100B aseTX/1000BaseT) 
H  Not used (Monitor port) 
I  Not...

  
SM 1-93 B230/B237/D042 
Installation 
1.22.9 CONNECTING COLOR CONTROLLER TO THE COPIER 
NOTE:  The installation of the Color Controller has already been done at 
the factory. You do not need to  perform the following installation 
procedure. This procedure is provided for your information only. 
 
Preparation for Installing the Color Controller E-3000 
After you unpack the Color Controller, conne ct the Color Controller to the copier 
before you connect it to the network. This  is to confirm that...

 
B230/B237/D042 1-94 SM 
4.  Remove the controller box cover 
[B] (  x 8).   
5.  Remove the lower memory [C] of  the two DIMM memories. 
 
 
 
 
 
6.  Remove the mother board bracket [D]  (  x 6). 
7. Attach the mot her board [E] to the 
mother board bracket (  x 4). 
8.  Reinstall the mother board [E] with  the mother board bracket [D] to the 
BICU board (  x 6). 
9.  Remove all SD slot covers on the left  side of the controller box. 
10. Remove all SD cards from the three  SD slots. 
11. Remove...

  
SM 1-95 B230/B237/D042 
Installation 
14. Reassemble the I/F slot cover, SD slot covers, controller box cover and rear 
cover. 
15.   Remove the Slot Covers of the  printer key and scanner key slots on the 
operation panel of the copier, and then discard them. 
 
16. Install the Fierydriven key top in  the slot, which was for printer key 
and the blank key top in the slot, 
which was for scanner key. 
17. Change the setting of SP5-985-001  from 1 (default) to 0. 
18. Attach the Fiery Decal [H] to the...

 
B230/B237/D042 1-96 SM 
Connecting the Color Controller to the Copier 
19. Connect the interface cable as follows:   
1) “Copier Side” [A]: Connect  this to the extension card. 
2) “Controller Side” [B]: Connect this to  the video interface on the rear of the 
Color Controller. 
NOTE:  If the interface cable is connect ed in the opposite direction, the 
copier engine will fail to communi cate with the controller.   
20. Connect the AC power cord [C] to  the power connector at the back of the 
Color...

  
SM 1-97 B230/B237/D042 
Installation 
1.22.10  STARTUP AND INITIAL SETUP 
1.  Connect the power cord of the copier to a power outlet and switch on the 
copier main power. 
NOTE:  1) The copier must be turned on befor
e you turn the Color Controller on.
2) Make sure that all firmware modu les for the copier are updated to the
newest versions. If they are not,  update them before you turn on the 
Color Controller.   
2.  Turn the power switch on the  Color Controller back panel to ON. 
3.  Allow startup...

 
B230/B237/D042 1-98 SM 
If you selected “English” at the 
language selection screen, you are 
prompted to select the market region. 
Select either “ US” or “UK” with the 
down arrow “ ” key and up arrow 
“  ” key, then touch “ OK”. 
 
6.  “Please wait…” will be indicated 
on the Fiery menu screen, then 
the Fiery menu screen will 
disappear from the operation 
panel. 
7.  Wait for a moment, then press the  Fierydriven key again on the 
operation panel. The Setup main 
menu will appear on the Fiery...