Ricoh Mp C3000 Service Manual

  
SM 1-79 B230/B237/D042 
Installation 
 
 
Diagnostic Report:  “ROM No. / Firmware 
Version” [A] “Loading Program” [B] 
Data Overwrite Security 
Unit   HDD Format Option: 
B7355060 / 0.03 GW2a_zoffy: 
B7355060 / 0.03 
 
ƒ  The ROM number and firmware version number change when the firmware is 
upgraded. However, the important thing is to make sure the numbers in [A] are 
the same as the numbers in [B]. 
ƒ  If the ROM numbers are not the same, or  the version numbers are not the same, 
this means the...

 
B230/B237/D042 1-80 SM 
1.20.11 USB HOST INTERFACE 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
 
1.  If the IEEE1394 unit is installed in I/F Card Slot A, remove it. 
2.  Remove the slot cover [A] from I/F Card Slot A (
 x 2). 
3.  Install the USB Host Interface [B] (Knob-screw x 2) into I/F card slot A. 
4.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end of this section).  

  
SM 1-81 B230/B237/D042 
Installation 
1.20.12 PICTBRIDGE 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
 
ƒ  You must install the PictBridge option in SD  Card slot 2. However, the Postscript 
option and the data overwrite security unit opt ion are also installed in SD Card slot 
2. You must do the SD Card Appli move procedure first if you have the postscript 
or data overwrite security unit option installed and you want to install the 
PictBridge unit. 
ƒ  You must...

 
B230/B237/D042 1-82 SM 
1.20.13 BROWSER UNIT TYPE B 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
SD card slot 3 is basically used only for serv ice maintenance. Do not leave an SD card in 
slot 3 after installing an application. 
 
1.  Remove the slot cover [A] from SD card slot 3 (
 x 1). 
2.  Turn the SD-card [B] label face to the rear of the machine. Then push it slowly 
into slot 3 until you hear a click. 
3.  Plug in and turn on the main power switch. 
4....

  
SM 1-83 B230/B237/D042 
Installation 
18. Touch OK. 
19.  Touch Exit twice to go back to the copy screen. 
20.  Turn off the main power switch. 
21.  Remove the SD card from slot 3. 
22.  Attach the slot cover [A] (
x 1). 
 
1.20.14 VM CARD TYPE C (JAVA PLATFORM) 
 
ƒ  Unplug the main machine power cord before you do the following 
procedure.  
Do not remove the SD card from sl ot 3 after installing the platform. 
 
1.  With the power OFF and the machine  unplugged, remove the slot cover [A] from 
SD...

 
B230/B237/D042 1-84 SM 
5.  Wait five minutes, and then press the “Other function” key. You will hear two 
beeps. z  If the screen does not change, this means  the installation is not finished yet. 
Wait a few more minutes and then pre ss the “Other function” key again. 
z   When the installation is finished, the following will be displayed: 
 
 
 
 
 
 
 
 
 
 
 
6.  Set the heap size and stack size for  the application. (In User Tools/Extended 
Features setting, see the Ad ministrator Tools tab.) 
7....

  
SM 1-85 B230/B237/D042 
Installation 
1.21 REMOTE COMMUNICATION GATE INSTALLATION 
1.21.1 COMPONENT CHECK 
No. Description Q’ty 
1  Remote Comm. Gate Interface  1 
2 Cover  1 
3 Screw 3 
1.21.2 INSTALLATION PROCEDURE 
1.  Remove one cover bracket from I/F Card Slot B ( x 2) 
2.  Install the modem board into the card slot for the device (  x 2). 
3.  Check the following SP settings before  starting the installation flow chart 
ƒ  SP5-816-150 (To Select the country) 
ƒ  SP5-816-154 (To set the...

 
B230/B237/D042 1-86 SM 
 
Rev. 03/2007
  

  
SM 1-87 B230/B237/D042 
Installation 
1.22 FIERY E-3000 (B889) 
1.22.1 ENVIRONMENT 
1. Temperature Range:  5°C to 40°C (41°F to 104°F) 
2.  Humidity Range:  10% to 90% RH 
3.  Ambient Illumination:  Less than 1500 lux  (do not expose to direct sunlight 
or strong light) 
4.  Ambient Dust:  Less than 0.10 mg/m3 
5.  If the place of installation is ai r-conditioned or heated, do not place the 
machine where it will be: 
1) Subjected to sudden temperature changes 
2) Directly exposed to cool air from an...

 
B230/B237/D042 1-88 SM 
1.22.3  MINIMUM SPACE REQUIREMENTS 
Place the machine near the power source, providing clearance as shown. 
You may place the E-3000 on the rear side of the large capacity tray or finisher 
as shown in the illustration. 
 
 
1.22.4 POWER REQUIREMENTS 
 
1.  Insert firmly the plug in the outlet. 
2.  Avoid using an outlet extension plug or cord. 
3.  Ground the machine. Avoid using  a 3-prong adapter in a 2-hole ungrounded 
outlet. 
4.  Use the supplied AC power cord with this...