Panasonic Wv Ns324 Operating Instructions Manual

-42- Notes:
•A scene magnified by the electronic zoom
function may be inferior in picture quality to a
non-magnified one.
•The electronic zoom does not function in the
preset position setting mode.
•To set preset positions directly from the WV-
CU550CJ, WV-CU360CJ or WV-CU161 System
Controller, you need to set the electronic zoom
function temporarily to OFF.
●Electronic Sensitivity Enhancement
(SENS UP)
1. Move the cursor to SENS UP and select the
desired electronic sensitivity enhancement mode
by using...

-43- 8. Dwell Time
Move the cursor to DWELL TIME, and select a time
with the Joystick.
When the time specified here elapses after motion
detection, the camera will notify the connected
device of the alarm activation. The default setting is
2 seconds.
Selectable times (seconds): 2s, 5s, 10s, 30s
Important Notices:
•The following conditions should be met for motion
detection.
1) The picture size on the screen should be larg-
er than 1/48 of the actual picture size.
2) The contrast ratio between the object...

-44-
(7) To Restore the Camera Default Position
(REFRESH)
Move the cursor to REFRESH by using the joystick
and press the [F2] button of the WV-CU550CJ.
For the WV-RM70, WV-CU360CJ or WV-CU161C,
keep pressing the Right and Left switches simulta-
neously for 2 seconds or more.
(8) Camera Resetting (CAMERA RESET)
Move the cursor to CAMERA RESET by using the
joystick and press the [F3] button of the WV-
CU550CJ.
The camera is reset to the factory settings.
For the WV-RM70, keep pressing the Right, Left
and...

-45- The camera setup menus overlaid on the camera picture appear by clicking the [Camera] button in the main window.
You will be prompted by the authentication dialog box. Enter admin in the user line if you have not registered it yet,
or enter the registered user name and password if user authentication is applied. Menu control buttons are lined up in
the lower part of the screen.
Note:The following pages mainly describe the unique setup operations of the PC. Refer to PRIOR TO SETUP on
page 26 for...

-46- The setup windows listed below are accessible with the
PC. The operations in these windows are described on
the following pages.
Click the setup menu buttons on the screen.
The following appear:
Camera
Multi screen
Network
Image
Alarm
FTP Client
User
Host
System
■Image Setup
1. Click the [Image] button.
2. Select the parameter for each item by pressing the
[o] button.
Refresh Interval:Fast, Middle, Slow, and Very
SlowResolution:640x480*, 640x240, 320x240, and
160x120
Quality of Image:Super Fine,...

-47- Note:Input an external alarm signal of more than
100 ms.
3. Alarm Preset
Select the item by pressing the [o] button, and
click the [SET] button.
1POSI:Camera performs according to Preset posi-
tion 1 when there is input at ALARM IN 1.
2POSI:Camera performs according to Preset posi-
tion 2 when there is input at ALARM IN 2.
OFF:No alarm preset used. Set Preset position 1
and 2 in advance when using this function.
The default setting is OFF.
4. E-mail Notice Setup
E-mail Notice:In ON position, an...

-48- 1. Click the [FTP Client] button.
2. Common Setup
•Enter the FTP server address.
A hostname.domainname can be entered
when using the DNS function.
•Enter the user name in a maximum of 16 char-
acters.
•Enter user name and password in a maximum
of 16 characters to access the FTP server.
•Select Sequential or Passive as the transmis-
sion mode. Passive is recommended when
Sequential does not perform properly.
•Complete schedule 1 and 2 by specifying the
transmission time zone and the day of the
week....

-49-
■Host Setup
1. Click the [Host] button.
2. Host Authentication
•Select [ON] or [OFF], and click the [SET] but-
ton.
ON: Applies the host authentication.
OFF:Does not apply.
3. Host Registration
•Enter the IP address of the PC.
A hostname.domainname can be entered
when using the DNS function.
•Select an access level, and click the [SET]
button. The default setting is level 1.
1 (Administrator):Allows you to operate
setup menus and to view live and record-
ed images.
2 (Camera Control):Allows you to...

-50- 4. Time zone
Enter the time difference between your site
and GMT.
Settings from 0:00 to 13:00 are valid.
Select +/– by pressing the [o] button, and
click the [SET] button.
3. Time Setup
For Manual setting use only:
Enter the month, date, year, hour, minute and sec-
ond, and click the [SET] button.
4. Time Display
Select Time Display ON/OFF by pressing the [o]
button.
ON:Enables the time display on the HTML window.
ON (L-UP):Positioned at upper left.
ON (L-LOW):Positioned at lower left.
ON...

-51-
■Auto Pan Setting
Click the [Camera] button in the Setup menu, and then
click the [Auto Pan] button.
START POINT:
1. Take the viewpoint as START POINT by press-
ing the joystick oval button, and adjust ZOOM,
FOCUS and IRIS by pressing the respective
function buttons.
2. Click the [START POINT] button to assign the
starting position.
END POINT:
1. Take the viewpoint as END POINT by pressing
the joystick oval button, and adjust 
ZOOM, FOCUS and IRIS by pressing the
respective function buttons.
2....