Panasonic Wv Ns324 Operating Instructions Manual

-11- 5. Tighten the fixing screw M3 (provided).
Notes:
(1) Tighten the camera fixing screw with a screw-
driver.
(2) Follow the instructions given here to ensure
that the camera and camera mounting base
are installed safely.
(3) When removing the camera from the camera
mounting base, loosen and press up the cam-
era fixing screw (M3) by using a screwdriver.
6. Fix the decoration cover to the camera mounting
base.
a. Sideway Cable Exit
Pass the cables through the cutout made in the
diecast case and...

ContactInsert UpAApprox.
3 mm (0.1 inch)
Insert the wire until A position
and clamp the contacts.Wire
Note:When powered up, the unit performs a self-
check (including one panning, tilting, zooming
and focusing operation).
•24 V AC Power Supply ConnectionPrepare the individual conductors for clamping. Use
MOLEX band tool part number 57027-5000 (for UL-
Style Cable UL1015) or 57026-5000 (for UL-Style
UL1007) for clamping the contacts.
After clamping the contacts, push them into the proper
holes in the...

-13- •Ethernet Connection
q Red
Data transmission
Data receptionOrange
Yellow
Green
w
e
r
t
y
u
i
TX +
RX +
RX – TX –
•ALARM IN Connections
An 8-pin and a 4-pin harness are supplied with the
camera as standard accessories. Connect external
sensors to this connector. Input specifications are
low-active, non-voltage contact (ON when active)
or open collector (Low when active). The table
below shows wire colors versus pin functions.
•ALARM OUT/AUX OUT Connections
Connect an external device, for example, a...

-14- • 
Connection to Intranet (Type 2)
A switching hub connected to the intranet is placed
between the camera and the PC.
Necessaries: 
•Straight-type network cable (Category 5)
•Switching hub or router (for 10BASE-T/100BASE-
TX)
• Connection to Internet (Type 3)
The PC accesses the camera through the Internet and
the DSL/CATV modem.
Necessaries: 
•Straight-type network cable (Category 5)
•CATV modem (cable modem) or DSL modem 
• 
Connection to Internet (Type 4)
A switching hub or a router may be added...

-15-
SETUP WITH PC
Notes:
•Do not access this menu through HTML or con-
trollers during the Panasonic IP Setup procedure.
•Only one administrator is required.
■Setup with the Provided
Panasonic IP Setup Software
Set up the network of the camera using the Panasonic
IP Setup software included on the CD-ROM provided
with the camera.
Note:If a firewall (including software) exists, allow
access to all UDP ports. Otherwise, it is impossible
to use the Panasonic IP Setup software.
In the English folder included...

-16-
PREPARATIONS FOR THE PC
■Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera. 
The following are the default network settings of the
camera.
IP address : 192.168.0.10
Subnet mask : 255.255.255.0
Default gateway : 192.168.0.1
To access the camera, the IP address of the PC should
be 192.168.0.XXX (where XXX should be a number
from 2 to 254 except 10).
Note:The procedure described below is based on the...

-17- 7. Click the Use the following IP address radio but-
ton and enter the IP address and the subnet mask
as follows.
IP address : 192.168.0.9
Subnet mask : 255.255.255.0
8. Click the [OK] button, and the window dialog box
closes.
Note:Use a small sized picture when a blue pic-
ture appears instead of the live picture due to
Internet traffic congestion.
■Network Setup of the Camera
On completion of the network setup of the PC, begin
the network setup of the camera. If two or more cam-
eras are...

-18- 3. Click the [Setup Menu] button. The User adminis-
tration window appears.
•Enter admin in the user line.
Note:The default setting is admin. The adminis-
trator should change the user name and pass-
word in the User Setting Menu.
4. Click the [OK] button. The Setup Menu window
appears.5. Click the [Network] button. The Network Setup
window appears.
6. Enter parameters for each item in the columns.
The parameters differ depending on the connec-
tion type. 

-19-
■Network Setup Parameters vs. Connection Type
Connection type Item Parameter description
Connection type 1 IP address Enter 192.168.0.XXX (where XXX should be a number from 2 to
254 except the same IP addresses already assigned to the PC or
any other cameras).
Net mask Use the default setting 255.255.255.0 for the subnet mask.
Default gateway 192.168.0.1
Host name NW_Camera
Network speed Select the network speed by pressing the [o] button.
Selectable parameters: Auto (default setting), 100 Mbps...

-20- Connection type Item Parameter description
Connection type 3 IP address Enter the IP address assigned by your Internet service provider.
The setting is not required if your Internet service provider uses a
DHCP server (the DHCP server assigns an IP address to the
camera automatically).
Subnet mask Enter the Net mask assigned by your Internet service provider.
The setting is not required if your Internet service provider uses a
DHCP server (the DHCP server assigns an IP address to the
camera...