Panasonic Wv Ns324 Operating Instructions Manual

-21- Connection type Item Parameter description
Host name Contact your Internet service provider and enter the assigned host
name if required.
Network speed Select the network speed by pressing the [o] button.
Selectable parameters: auto (default setting), 100 Mbps (full
duplex), 100 Mbps (half duplex), 10 Mbps (full duplex), 10 Mbps
(half duplex)
HTTP port If two or more cameras are connected, each camera needs to be
set up individually.
The port numbers already assigned to other hardware are not...

-22- 3. Enter admin in the user name line. According to
the default setting, you need not enter the pass-
word. The Network Setup window appears.
4. Set the following parameters.
Note:Ask your system administrator about param-
eters if you are unsure.
IP Address:Enter numbers 0 through 255 into four
sections split by dots.
Netmask:Enter numbers 0 through 255 into four
sections split by dots.
HTTP Port:Enter different numbers for each when
multiple cameras are connected.
DHCP (Dynamic Host Configuration...

-23- You can operate the camera in two ways: with the PC
by way of network, or with the Matrix Switcher system
controllers. 
Access from the PC
Your PC can access the camera to view images, to
control and to set up menus. 
Prior to operating from the PC, confirm that connections
are made properly as shown in CONNECTIONS on the
previous page.
1. Start up the PC.
2. Start up the Web browser, Internet Explorer or
Netscape Communicator.
3. Enter the IP address of the camera in the address
bar.
The factory...

-24- You can monitor pictures from multiple cameras on a
multiscreen on the monitor multiscreen
Pictures of up to four cameras can be displayed as a
group.
To monitor camera pictures on the multiscreen, the
cameras need to be set up in advance. (See p. 50 for
details.)
Note:Only still pictures (JPEG) can be monitored on a
multiscreen.
1:Spot, go-return switch button
1-4:Multiscreen 1-4 (Group A), go-return switch
button
5-8:Multiscreen 5-8 (Group B), go-return switch
button
Click the Multiscreen 1-4 or...

-25-
•Function Comparison / PC Network vs. Camera site
Function PC Network Camera Site (*1)
VIEWING IMAGES
PAN/TILT A A
ZOOM/FOCUS A A
IRIS A A
PRESET A A
AUTO PAN A A
360MAP A NA
AUX Device Control A NA
Alarm Log/Alarm Image Display A NA
MENU SETUPS
Camera Setup (Camera) A A
Network Setup (Camera) A A
Network Setup (HTML)  A NA
Operating Mode Setup (HTML)  A NA
Alarm Setup (HTML)  A NA
FTP Client Setup (HTML)  A NA
User Authentication (HTML)  A NA
Host Authentication (HTML)  A NA
System Setup (HTML)  A...

-26- This section describes setup procedures common to
accesses from the PC, e.g. transmitting images to an
FTP server, sending alarm notice mail, auxiliary device
control, clock setup, and LED control.
Buttons Used for Setup Menus
Click the buttons on the computer display. Each button
is assigned functions in the setup as follows.
Camera Setup Menus
• From the PC
1. Open the main page of the WV-NS324 camera,
referring to page 45.
Login as a level-1 administrator in the dialog box if
requested.
2. Click...

-28--27-
■Setup Menu
Setup menus are shown in the diagram below. These enable you to adapt th\
e camera to your own requirements.
The menus are described on the following pages for reference prior to se\
tup.
Switches, keys and the joystick are used for setup operations.
SETUP
Setup
MenuPresetting (P. 30)
Map Menu
Home Position Setting (P. 34)
Self-return Setting (P. 34)
Auto Mode Selection (P. 34)
Flip-A-Chip Setting (P. 36)
Cleaning (P. 36)
Image Hold (P. 36)
Camera Setting (P. 37)
Camera...

-29-
Function/Controller
Open CAM SETUP
Open Special All Reset
F2 keyWV-CU550CJ WV-CU360C WV-CU161C WV-RM70
See page 30CAM SETUP
key (for 2 sec-
onds or more)
CAMERA SETUPkey (for 2 seco-
nds or more)PROG SW
(for 2 seconds
or more) and
SET SW at
CAMERA
SETUP on
Program Menu
Close CAM SETUP F4 keyCAM SETUP
key (for 2 sec-
onds or more)
CAMERA SETUPkey (for 2 seco-
nds or more)PROG SW
Move the cursorJoystick
(←, ↑, ↓, →)Joystick
(←, ↑, ↓, →)Direction SW
(←, ↑, ↓, →)Direction SW
(←, ↑, ↓, →)
Select a...

-30- The following setting procedures are described on the
assumption that this model is used in combination with
the WJ-SX550C Matrix Switcher and WV-CU550CJ
System Controller. In case a controller other than the
WV-CU550CJ is used, refer to the table on page 29.
■Menu Display
●Setup Menu Display
WV-CU550CJ
1. Select the camera number you want to set up and
a monitor to display the SET UP MENU.
2. Display the D4 menu on the LCD by pressing the
appropriate cursor buttons.
3. Press the [F1] button.
SET UP...

-31-
●Position Setting (POSITION SET)
Aligns the camera position and focal point by panning,
tilting, zooming and focusing.
1.Move the cursor to POSITION SET on the preset
setting menu and press the CAM (SET) key.
The position setting menu appears.
2. To Set Panning/Tilting Positions
(1) Move the cursor to PUSH SET for PAN/TILT
and press the CAM (SET) key. The PAN/TILT
setting menu appears.
(2) Select panning/tilting positions by moving the
joystick up and down, right and left, and press
the CAM (SET)...