Panasonic Wv Ns324 Operating Instructions Manual

You can reset the following data to the factory default
settings.
Camera Setup
HTML files
Setting the Switches
The camera is provided with an 8-bit DIP switch. The 8-
bit DIP switch is used to return the camera to the facto-
ry default settings. Switch settings are read into the
camera when the power is turned on. Make sure to turn
the camera off, then turn it back on after changing the
switch settings. Switch positions and functions are
shown below.
Note:All DIP switches except SW1 and SW2 should
always...

-53-
■Still Picture Storage to the PC
The camera picture can be saved as a still image on
your PC.
1. Move the cursor to the picture area on the screen,
and right-click to select Save As.
2. Enter a file name to be assigned to the picture, and
specify the storage place in the dialog box.
3. Click Save.
VIEWING PICTURES 

Pixel
numbers
-54- When alarm arises, the camera performs output func-
tions according to the setup.
Inputs: 
•Input from ALARM IN 1 and ALARM IN 2.
•Input from the built-in VMD (Video Motion Detector)
that detects motion in video by monitoring a speci-
fied area.
Outputs:
•The message Alarm is displayed in the upper
right corner of the Main Menu, Camera Control win-
dow and Alarm List.
•The picture files of alarm events are stored in the
camera.
•An e-mail notifies the specified addresses of the
alarm...

-55-
■Transferring Picture Files
•Set FTP setup menu.
•Pre- and post-alarm picture files can be sent to and
stored on a designated FTP server.
•A picture file attached to a mail can be sent to the
specified mail addresses.
Note:When many alarm events arise at the same time,
it may happen occasionally that a mail is sent with-
out an alarm picture attached.
■Canceling Alarm Display
1. Indicating ALARM in the top window or in the
Camera Control window:
•Click the [Setup Menu] or [Alarm List] button.
2....

-56- 5. Move the cursor to MASK SET, and click the [SET]
button.
The detection map is split into 48 areas with status
indications for each.
Transparency:Indicates a non-masked area that
has been incorporated into the detection area.
Blink:Indicates a non-masked area when the
cursor is on it.
Highlight:Indicates a masked area that has
been exempted from detection.
Stripe:Indicates an already masked area
when the cursor is on it.
6. Move the cursor to an area, and click the [SET]
button.
•The area will...

-57-
■Reviewing Alarm Pictures 
The alarm pictures stored in the camera can be
reviewed on the PC.
1. In the main window, click the [Alarm List] button.
2. Click the pertinent Data/Time in the list.
You can confirm the pictures of past alarm events.
Type TRM1: Alarm through Terminal 1
TRM2: Alarm through Terminal 2
VMD: Alarm through Video Motion
Detector
1:  One alarm event picture attached
: More than one alarm event pic-
ture attached
3. The selected picture is displayed, and the alarm
image control...

-58-
■Resetting Alarm 
You can reset the alarm output functions being activat-
ed.
1. In the main window, click the [Setup Menu] button.
2. Click the [Alarm] button to open the Alarm Setup
window.
3. Find External Alarm Reset in the window.
4. Click the [Alarm Reset] button.
5. Click the [Go to Main Menu] button to go back to
the main window.How to customize contents of e-mail notification
You can customize the contents of e-mails notifying the
recipient of alarm events and their dates.
Take the...

-59- File Name:almmail.tmpl, a template for alarm
e-mail notifications.
Use the provided file name.
Step 2
Start up the Windows DOS prompt and connect by
inputting the IP address of the unit.
For the FTP software, use the user name and
administrator password (level 1) registered in the
User Setting window.
If no administrator has been registered, proceed as
follows:
User Name:admin
Password:None
Step 3
Upload the file(almmail.tmpl) to this unit.
Note:Do not upload with FTP when connecting
with low baud...

-60-
■Auxiliary Output Control
You can turn a connected device on or off, for example
a lamp that is connected to the AUX OUT terminal of
the camera.
1. Set this item on the Camera Control window.
2. Select the polarity for switching the connected
device on or off.
High:Supplies high voltage.
Low:Supplies low voltage.
Note:The initial state when the camera is turned
on is HIGH.
AUXILIARY OUTPUT CONTROL 

-61-
TROUBLESHOOTING
Symptom
No picture is displayed.
HTML documents are not displayed.• Is the AC adapter firmly plugged in to the outlet?
• Are the POWER IN terminals on the camera connected with
the AC adapter properly?
• Is the video cable or network cable connected properly? 
• HTML files in the camera might be broken. Initializing is
required.8, 12
52 Cannot access the camera from the
browser.• Are the network cables connected properly?
• Is the status indicator lamp of the network connection...