Panasonic Wv Ns324 Operating Instructions Manual

-32-
●Preset Identification Setting (PRESET
ID)
Assigns a name to preset IDs (identification of up to 16
alphanumeric characters) and can be switched on or
off on the monitor screen.
1.Move the cursor to PRESET ID on the preset setting
menu and select ON or OFF by moving the joystick
to the right or left.
The factory default setting is OFF.
2.Press the CAM (SET) key to display the preset ID
setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using
the joystick, and press...

-33-
●Light Control Setting (ALC/MANUAL)
Selects the ALC or MANUAL mode for adjusting the
lens iris.
1. The factory default setting is ALC.
ALC:The lens iris is automatically adjusted to suit
the brightness of the object.
MANUAL:The lens iris is fixed at the set value
regardless of the brightness of the object.
2. In case of ALC O
Press the CAM (SET) key. The backlight compen-
sation menu appears on the monitor screen. See
page 37 for the setting.
3. In case of MANUAL O
Press the CAM (SET) key. The...

-34- 3. Move the cursor to DEL and press the CAM (SET)
key.
This deletes the preset position and the PRESET
NUMBER SET menu appears. The * mark to the
right of the number disappears.
■Home Position Setting (HOME
POSITION)
The home position is the camera’s basic position.
It returns to this position automatically when a specific
time has elapsed after a manual operation. This setting
functions only when AUTO MODE is OFF.
1. To set a position number for the home position
The factory default setting is...

-35- 3. Panning starting point and panning endpoint
Follow the steps below.
(1) Move the cursor to POSITION and press the
CAM (SET) key. The cursor moves to START.
(2) Move the joystick to the right or left to select a
panning starting point and press the CAM
(SET) key.
This determines the starting point and the cur-
sor moves to END.
(3) Move the joystick to the right or left to select a
panning endpoint and press the CAM (SET)
key.
This determines the endpoint, and the cursor
moves to POSITION.
4....

-36- Notes:
•When the panning or tilting in the AUTO PAN
mode is controlled manually, the Auto mode
function should be cancelled.
To activate the auto mode, select the AUTO
PAN mode again or set a time for SELF
RETURN in the SET UP menu.
•Auto refreshing may be activated during the
auto mode to calibrate the lens position.
■Flip-A-Chip Setting
FLIP-A-CHIP is for setting the movement of the camera
by using the joystick.
The factory default setting is OFF.
OFF:Tilt range is limited to 0 ° to 92 °.
ON:The...

-37-
■Camera Setting
To Display the Camera Setting Menu
Move the cursor to CAMERA O, and press the CAM
(SET) key. The camera setting menu appears.
●Camera Identification (CAMERA ID)
You can use the camera identification to assign a name
to the camera. The camera ID consists of up to 16
alphanumeric characters. You can select whether to
have the camera ID displayed on the monitor screen or
not.
The factory default setting is OFF.
ON:Camera ID appears on the monitor screen.
OFF:Camera ID does not appear....

2. Move the cursor to MASK SET and press the
CAM (SET) key. The 48 mask areas appear on
the monitor screen. The cursor is blinking in
the top left corner of the screen.
3. To mask an area where backlight is bright,
move the cursor to the area and press the
CAM (SET) key. The mask turns to white.
Repeat this procedure to mask the desired
area.
4. To cancel a masked area, move the cursor to
the area, and press the CAM (SET) key. To
cancel all masked areas, press the [F2] button
of the WV-CU550CJ. For the...

-39- 6. If you want to change the video output level
(picture contrast), move the I cursor for
LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM
(SET) key to return to the CAM SET UP menu.
To return to the camera picture, press the [F4]
button.
●Shutter Speed Setting (SHUTTER)
You can select a shutter speed from among 1/60 (OFF),
1/100, 1/250, 1/500, 1/1000, 1/2000, 
1/4 000, and 1/10 000 seconds.The factory default set-
ting is OFF.
The electronic shutter speed changes as follows...

-40- 5. Move the cursor to COARSE by using the joystick.
6. Match the vertical phases for both video output sig-
nals as closely as possible by using the joystick.
The coarse adjustment can be incremented in
steps of 22.5 degrees (16 steps) with the joystick.
Note:After the 16 steps, the adjustment returns to
the first step.
7. Move the cursor to FINE by using the joystick.
8. Use the joystick to match the vertical phase for
both video output signals as closely as possible.
Notes:
•When the | cursor...

-41- 2. For fine adjustment of the ATW, press the CAM
(SET) key. The ATW fine adjustment menu appears
on the monitor screen.
3. Move the cursor to RET by using the joystick and
press the CAM (SET) key to return to the SET UP
menu.
(2) Automatic White Balance Control Mode
(AWC)
1. Move the cursor to WHITE BAL and select AWC →
PUSH SET by using the joystick.
2. Press the CAM (SET) key to start the white balance
setup. PUSH SW is highlighted to indicate that
white balance is being set.
3. PUSH SW returns to...