Panasonic Wv Ns324 Operating Instructions Manual

							-32-
●Preset Identification Setting (PRESET
ID)
Assigns a name to preset IDs (identification of up to 16
alphanumeric characters) and can be switched on or
off on the monitor screen.
1.Move the cursor to PRESET ID on the preset setting
menu and select ON or OFF by moving the joystick
to the right or left.
The factory default setting is OFF.
2.Press the CAM (SET) key to display the preset ID
setting menu.
To Enter a New Preset ID
(1) Move the cursor to the desired character using
the joystick, and press the CAM (SET) key.
(2) The selected character appears in the editing
area. (The pointer in the editing area moves to
the right automatically at this moment.) To
enter a blank, select SPACE.
(3) Repeat the above procedure until all charac-
ters are entered.To Copy a Preset ID from Another Position
(1) Move the cursor to COPY and press the CAM
(SET) key. First the preset ID in the preceding
position is shown. Each consecutive pressing
of the CAM (SET) key displays the ID preced-
ing the one currently displayed.
(2) Display the desired ID.
(3) Follow the step To Change an Entered Preset
ID if necessary
To Set a Display Position for a Preset ID
(1) Move the cursor to POSI and press the CAM
(SET) key. The display position set menu
appears.
(2) Move the ID to the desired position by using
the joystick, and press the MON (ESC) key.
The display position is set and the monitor
screen returns to the preset ID setting menu.
To Enter the Next ID without Returning to the
Preset Setting Menu
(1) In the preset ID setting menu, move the cursor
to the top line and select a desired position
number by moving the joystick to the right or
left.
(2) Enter, copy, change or delete the ID as
described above.
To Return to the Preset Setting Menu
Move the cursor to RET and press the CAM (SET)
key.
     PRESET NO. 1
POSITION SET  
OPRESET ID     ON  OALC/MANUAL    ALC OAF MODE       MANUAL
RET   DEL
Command
Editing
Area
Character
Area
PointerCharacter Cursor
     PRESET NO. 1
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    ................
    
     PRESET NO. 1
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    ................
    
     PRESET NO. 1
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    ................
    
     PRESET NO. 1*
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    COPY POSI RET RESET
    DOOR............
     
						

							-33-
●Light Control Setting (ALC/MANUAL)
Selects the ALC or MANUAL mode for adjusting the
lens iris.
1. The factory default setting is ALC.
ALC:The lens iris is automatically adjusted to suit
the brightness of the object.
MANUAL:The lens iris is fixed at the set value
regardless of the brightness of the object.
2. In case of ALC O
Press the CAM (SET) key. The backlight compen-
sation menu appears on the monitor screen. See
page 37 for the setting.
3. In case of MANUAL O
Press the CAM (SET) key. The setting menu
appears on the monitor screen. Set the lens iris
level as desired by moving the joystick to the right
or left.
●Auto Focus Setting (AF MODE)
1. The factory default setting is MANUAL.
MANUAL:AF does not work after moving to a pre-
set position.
AUTO:AF works after moving to a preset position.
●To Return to the Preset Number Set
Menu
•Move the cursor to RET and press the CAM (SET)
key. The PRESET NUMBER SET menu appears
with the * mark to the right of the preset position
number.
●To Return to the Setup Menu
•Move the cursor to RET and press the CAM
(SET) key.
■Deleting Preset Positions
1. Move the cursor to PRESET 1 and select the posi-
tion number to be deleted by using the joystick.
2. Press the CAM (SET) key to display the preset set-
ting menu.
     PRESET NO. 1
POSITION SET  
OPRESET ID     ON  OALC/MANUAL    ALC OAF MODE       MANUAL
RET   DEL
   ** MANUAL CONT **
IRIS
RET••••|••••
CLOSE   OPEN
     PRESET NO. 1
POSITION SET  
OPRESET ID     ON  OALC/MANUAL    ALC OAF MODE       MANUAL
RET   DEL
 ** PRESET NUMBER SET **
   1     2     3     4
   5     6     7     8
   9    10    11    12
  13    14    15    16
   ID:
RET
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
     PRESET NO. 1
POSITION SET  
OPRESET ID     ON  OALC/MANUAL    ALC OAF MODE       MANUAL
RET   DEL 
						

							-34- 3. Move the cursor to DEL and press the CAM (SET)
key.
This deletes the preset position and the PRESET
NUMBER SET menu appears. The * mark to the
right of the number disappears.
■Home Position Setting (HOME
POSITION)
The home position is the camera’s basic position.
It returns to this position automatically when a specific
time has elapsed after a manual operation. This setting
functions only when AUTO MODE is OFF.
1. To set a position number for the home position
The factory default setting is OFF.
■Self-return Setting (SELF RETURN)
Self-return is the time-out parameter for returning to the
home position.
In ON position, the camera returns to AUTO MODE after
a specific time following a manual operation.
To set a time-out parameter for return to the home posi-
tion
•Move the cursor to SELF RETURN and select a
return time by moving the joystick to the right or
left.
The factory default setting is OFF.
Return time changes as follows:MIN stands for minute(s).
Note:The camera will return to the auto mode if
that is set to AUTO PAN when a specific time
has elapsed after a manual operation.
■Auto Mode Selection (AUTO
MODE)
AUTO MODE activates the cameras auto turn within the
preset panning range.
1. Auto mode
Move the cursor to AUTO MODE and select a
mode by moving the joystick to the right or left.
The factory default setting is OFF.
Modes change as follows:
OFF:No automatic operation. The camera can be
operated only manually.
AUTO PAN:You can activate the cameras auto
turn within the preset panning range.
2. When the AUTO PAN mode is selected, set details
as follows:
Move the cursor to AUTO PAN Oand press the
CAM (SET) key to display the AUTO PAN setting
menu.
 ** PRESET NUMBER SET **
   1     2     3     4
   5     6     7     8
   9    10    11    12
  13    14    15    16
   ID:
RET
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
2MIN 3MIN 5MIN 10MIN
60MIN
30MIN 20MIN1MIN
OFF
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     AUTO PAN
O FLIP-A-CHIP   ON
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
OFFAUTO PAN 
						

							-35- 3. Panning starting point and panning endpoint
Follow the steps below.
(1) Move the cursor to POSITION and press the
CAM (SET) key. The cursor moves to START.
(2) Move the joystick to the right or left to select a
panning starting point and press the CAM
(SET) key.
This determines the starting point and the cur-
sor moves to END.
(3) Move the joystick to the right or left to select a
panning endpoint and press the CAM (SET)
key.
This determines the endpoint, and the cursor
moves to POSITION.
4. Panning speed
The panning speed increases when the joystick is
moved to the right, and decreases when it is
moved to the left.Notes:
•If the panning range is changed after the camera
has not panned for a long time or has been pan-
ning in the same panning range, the picture may
not be clear or noise may appear. In this case, pan
the camera fully several times.
If this does not eliminate the problem, refer servic-
ing to qualified service personnel.
•When you press the CAM (SET) key, the camera
might move slightly to memorize the nearest pan-
ning/tilting position.
5. Pan limit ON/OFF
The factory default setting is OFF.
ON:Manual pan is limited from the starting point to
the endpoint specified by position setting. Set
ENDLESS to OFF before setting PAN LIMIT to
ON.
OFF:Manual pan is not limited.
Note:When ON is selected for PAN LIMIT, manual
pan moves the camera away from the other
side (PAN LIMIT) of the start-end range.
6. ENDLESS to ON/OFF
The factory default setting is OFF.
ON:The camera pans from the starting point to the
endpoint, and keeps rotating in the same
direction to return to the starting point. Set
PAN LIMIT to OFF before setting ENDLESS to
ON.
OFF:The camera pans from the starting point to
the endpoint, and rotates backward to the
starting point.
This movement is repeated over and over.
7. Dwell time
The factory default setting is 2S.
Dwell time changes as follows:
     ** AUTO PAN **
POSITION     START 
             END
SPEED        ••••|••••
             L       H
PAN LIMIT    OFF
ENDLESS      OFF
DWELL TIME   2S
RET
     ** AUTO PAN **
POSITION     START 
             END
SPEED        ••••|••••
             L       H
PAN LIMIT    OFF
ENDLESS      OFF
DWELL TIME   2S
RET
     ** AUTO PAN **
POSITION     START 
             END
SPEED        ••••|••••
             L       H
PAN LIMIT    OFF
ENDLESS      OFF
DWELL TIME   2S
RET
     ** AUTO PAN **
POSITION     START 
             END
SPEED        ••••|••••
             L       H
PAN LIMIT    OFF
ENDLESS      OFF
DWELL TIME   2S
RET
Camera Endpoint
Starting point Start-end
range of
auto panSelf-end 
range of
pan limit
    ** AUTO PAN **
POSITION
SPEED
PAN LIMIT
ENDLESS
DWELL TIME
RETSTART
END
••••|••••
L       H
OFF
ON
2S 
						

							-36- Notes:
•When the panning or tilting in the AUTO PAN
mode is controlled manually, the Auto mode
function should be cancelled.
To activate the auto mode, select the AUTO
PAN mode again or set a time for SELF
RETURN in the SET UP menu.
•Auto refreshing may be activated during the
auto mode to calibrate the lens position.
■Flip-A-Chip Setting
FLIP-A-CHIP is for setting the movement of the camera
by using the joystick.
The factory default setting is OFF.
OFF:Tilt range is limited to 0 ° to 92 °.
ON:The flip-a-chip function allows the tilt angle to
widen up to 180 °.
Note:Flip-a-chip does not work if PAN LIMIT is set to
ON.
■Cleaning (CLEANING)
CLEANING is used for refreshing the electro-mechani-
cal contacts built into the camera. Use this function for
maintenance when the camera has been directed at a
specific spot or panned over a specific range for a long
time.
Built-in electric mechanical contacts are refreshed at
regular intervals (approx. 7 days) if CLEANING is set to
ON.
A dry contact adversely affects picture quality and
motor operation.
The factory default setting is OFF.
ON:The contacts are cleaned for approx. 1 minute.
CLEANING disappears when the process is com-
pleted.
OFF:No contact cleaning
Note:Select OFF when the camera downloads or
uploads preset data.
■Image Hold (IMAGE HOLD)
The camera picture remains as a still image on the
monitor screen until the camera reaches the preset
position. The factory default setting is OFF.
2S 3S
30S 10S
20S
5S
     ** AUTO PAN **
POSITION     START 
             END
SPEED        ••••|••••
             L       H
PAN LIMIT    OFF
ENDLESS      OFF
DWELL TIME   2S
RET
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      ON
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
CLEANING
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   OFF
 CLEANING      OFF
 IMAGE HOLD    ON
 
 CAMERA 
O NETWORK O 
						

							-37-
■Camera Setting
To Display the Camera Setting Menu
Move the cursor to CAMERA O, and press the CAM
(SET) key. The camera setting menu appears.
●Camera Identification (CAMERA ID)
You can use the camera identification to assign a name
to the camera. The camera ID consists of up to 16
alphanumeric characters. You can select whether to
have the camera ID displayed on the monitor screen or
not.
The factory default setting is OFF.
ON:Camera ID appears on the monitor screen.
OFF:Camera ID does not appear.
Press the CAM (SET) key to display the camera ID set-
ting menu.To Enter a New Camera ID
(1) Move the cursor to the desired character using the
joystick, and press the CAM (SET) key.
(2) The selected character appears in the editing area.
(The pointer in the editing area moves to the right
automatically at this moment.) To enter a blank,
select SPACE.
(3) Repeat the above procedure until all characters
are entered.
Note:Refer to page 32 for POSI, RET and RESET.
●Light Control Setting (ALC/MANUAL)
You can select the mode for adjusting the lens iris.
There are two modes as follows:
ALC:The lens iris is automatically adjusted to suit the
brightness of the object.
You can select one of two modes (BLC ON or BLC
OFF) of backlight compensation.
Backlight compensation is available in the ALC
mode. It eliminates strong background light which
makes the camera picture dark such as a spotlight.
MANUAL:The lens iris is fixed at the value that you
have set regardless of the brightness of an object.
1. Display the SET UP menu on the monitor screen by
referring to page 29.
2. The factory default setting is ALC.
When you select ALC, set backlight compensation.
Note:The backlight compensation submenu asso-
ciated with this menu is described separately
and should be set up after installing the cam-
era at the site and observing the actual site
picture.
3. When MANUAL is selected, quit the setup menu by
pressing the MON (ESC) key. Press the OPEN or
CLOSE key on the controller for iris adjustment.
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   ON
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O   
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
     CAMERA ID --
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,:;&#!?=
     +-*/%$
    SPACE
    ----  POSI RET RESET
    ................
    
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O 
						

							2. Move the cursor to MASK SET and press the
CAM (SET) key. The 48 mask areas appear on
the monitor screen. The cursor is blinking in
the top left corner of the screen.
3. To mask an area where backlight is bright,
move the cursor to the area and press the
CAM (SET) key. The mask turns to white.
Repeat this procedure to mask the desired
area.
4. To cancel a masked area, move the cursor to
the area, and press the CAM (SET) key. To
cancel all masked areas, press the [F2] button
of the WV-CU550CJ. For the WV-RM70, press
the right and left switches simultaneously.
5. After masking is completed, press the MON
(ESC) key. The 48 mask areas on the monitor
screen disappear and the ALC CONT menu
appears.
-38- (1) ALC Mode with BLC ON
In normal use, the important object in a scene is
placed in the centre of the monitor screen. When
set at the factory, more photometric weight is given
to the centre of the screen than to the edge of the
screen (where bright backlight would most likely be
located). In such a case, the object at the centre of
the screen can be still clearly seen even though the
backlight may vary.
1. Press the CAM (SET) key after selecting ALC.
The ALC CONT menu appears.
2. Move the cursor to the BLC and select ON.
3. If you want to adjust the video output level,
move the I cursor for LEVEL. Adjust it to the
desired level by using the joystick.
4. Move the cursor to RET and press the CAM
(SET) key to return to the CAM SET UP menu.
To return to the camera picture, press the [F4]
button.
(2) ALC Mode with BLC OFF
This mode is effective when the main object in the
scene is not located in the centre of the screen but
a source of bright light is located near the centre of
the scene. In this mode, the picture is divided into
48 areas that mask the light to keep the clarity of
the picture.
Note:The result of field setup of the mask area and
level adjustment is fed back (effected) to the
lens iris control in ALC mode.
1. Move the cursor to the BLC and select OFF.
When you select MANUAL, BLC is not avail-
able. MASK SET appears on the menu.
    ** ALC CONT **
    BACK LIGHT COMP
BLC
MASK SET 
LEVEL
RETOFF
••|•••••
-       +
    ** ALC CONT **
    BACK LIGHT COMP
BLC
 
LEVEL
RETON
••|•••••
-       +
Blinking
Blinking
Blinking
Turns to white 
						

							-39- 6. If you want to change the video output level
(picture contrast), move the I cursor for
LEVEL and adjust the level.
7. Move the cursor to RET and press the CAM
(SET) key to return to the CAM SET UP menu.
To return to the camera picture, press the [F4]
button.
●Shutter Speed Setting (SHUTTER)
You can select a shutter speed from among 1/60 (OFF),
1/100, 1/250, 1/500, 1/1000, 1/2000, 
1/4 000, and 1/10 000 seconds.The factory default set-
ting is OFF.
The electronic shutter speed changes as follows by
using the joystick:
●Gain Control (AGC)
You can set the gain (brightness level portion of an
image) to automatic level adjustment ON (LOW, MID,
HIGH) or fixed level (OFF).
The factory default setting is ON (MID).Note:For more information, refer to Digital Noise
Reduction on page 43.
●Synchronization (SYNC)
You can select the internal sync (INT) mode or the line-
lock sync (LL) mode. Additionally, this model accepts
the VD2 signal (vertical drive signal multiplexed with the
composite video output signal) from a specified compo-
nent. Whenever the VD2 signal is supplied to this cam-
era, the camera automatically switches to the VD2 sync
mode.
When you select the line-lock sync (LL) mode, you can
adjust vertical phase.
The factory default setting is INT.
Important Notices:
1. The priority of sync modes is given as follows:
1. Multiplexed vertical drive (VD2) (highest priori-
ty)
2. Line-lock (LL)
3. Internal sync (INT) (lowest priority)
2. Whenever the vertical drive pulse (VD2) is supplied
to the camera, the camera sync mode is automati-
cally switched to the multiplexed vertical drive
pulse (VD2) regardless of the selected sync mode.
Line-lock Sync Mode (LL)
1. Move the cursor to SYNC and select LL by using
the joystick. LL sync mode is not available when
the multiplexed vertical drive (VD2) pulse is sup-
plied.
2. After selecting LL, press the CAM (SET) key.
The SYNC menu appears on the monitor screen.
3. Supply the video output signal of the camera to be
adjusted and the reference video output signal (for
example, Camera 1) to a dual-trace oscilloscope.
4. Set the dual-trace oscilloscope to the vertical rate
and expand the vertical sync portion on the oscillo-
scope.
    ** ALC CONT **
    BACK LIGHT COMP
BLC
MASK SET 
LEVEL
RETOFF
••|•••••
-       +
OFF (1/60)1/100
1/10 0001/4 000 1/2 000 1/1 0001/2501/500
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         LL 
OWHITE BAL    ATW OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O 
						

							-40- 5. Move the cursor to COARSE by using the joystick.
6. Match the vertical phases for both video output sig-
nals as closely as possible by using the joystick.
The coarse adjustment can be incremented in
steps of 22.5 degrees (16 steps) with the joystick.
Note:After the 16 steps, the adjustment returns to
the first step.
7. Move the cursor to FINE by using the joystick.
8. Use the joystick to match the vertical phase for
both video output signals as closely as possible.
Notes:
•When the | cursor reaches the + end, it
jumps back to –. At the same time, COARSE
is incremented by one step to enable a contin-
uous adjustment. The reverse takes place
when the | cursor reaches the – end.
•When the joystick is kept at the right or left for
one second or more, the | cursor moves
quickly.
•To reset COARSE and FINE to the preset val-
ues, press the [F2] button of the WV-CU550CJ.
For the WV-RM70, press the Right and Left
switches simultaneously. COARSE is preset to
zero-cross of the AC line phase.
•If the AC line contains noise (spike noise, etc.),
the stability of the vertical phase of the camera
video output signal may be disturbed.
●White Balance (WHITE BAL)
(1) Auto-Tracing White Balance Mode (ATW)
In this mode, the color temperature is monitored contin-
uously and thereby white balance is set automatically.
The color temperature range for the proper white bal-
ance is approx. 2 600 to 6 000 K. Proper white balance
may not be obtained under the following conditions:
1. The color temperature is out of the 2 600 to
6000 K range.
2. When the scene contains mostly high color
temperature (bluish) objects, such as a blue
sky.
3. When the scene is dim.
In these cases, select the AWC mode.
1. Move the cursor to WHITE BAL and select ATW by
using the joystick. 
The factory default setting is ATW.
The white balance of the camera is automatically
set.
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
•|•••••••
-       +
1 (1 - - 16): 0 degrees
2 (1 - - 16): 22.5 degrees
16 (1 - - 16): 337.5 degrees
   ** SET UP MENU **
PRESET  1 O 
 MAP O 
 HOME POSITION OFF
 SELF RETURN   OFF
 AUTO MODE     OFF
 FLIP-A-CHIP   ON
 CLEANING      OFF
 IMAGE HOLD    OFF
 
 CAMERA 
O NETWORK O
      ** SYNC **
V PHASE
COARSE
FINE
RET4(1--16)
••••••|••
 -      +
      ** SYNC **
V PHASE
COARSE
FINE
RET1(1--16)
•|•••••••
 -      +
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O 
						

							-41- 2. For fine adjustment of the ATW, press the CAM
(SET) key. The ATW fine adjustment menu appears
on the monitor screen.
3. Move the cursor to RET by using the joystick and
press the CAM (SET) key to return to the SET UP
menu.
(2) Automatic White Balance Control Mode
(AWC)
1. Move the cursor to WHITE BAL and select AWC →
PUSH SET by using the joystick.
2. Press the CAM (SET) key to start the white balance
setup. PUSH SW is highlighted to indicate that
white balance is being set.
3. PUSH SW returns to normal when balance setting
is completed.
4. For fine adjustment of the AWC, move the cursor to
AWC and press the CAM (SET) key. The AWC fine
adjustment menu appears on the monitor screen.
5. Move the cursor to RET by using the joystick and
press the CAM (SET) key to return to the SET UP
menu.
●Auto Focus Setting (AF MODE)
The camera adjusts the focus automatically by sensing
the centre of the picture.
MANUAL:Auto-focus is activated only when the AF key
on the controller is pressed.
AUTO:Auto-focus is activated automatically while a
manual pan, tilt or zoom operation is pe
The factory default setting is AUTO.
Note:
The auto focus lens may not function properly in
the AUTO mode under the following conditions.
1. Dirt or water on window glass
The auto focus may focus on the dirt or water.
2. Low lighting or illumination
3. Bright objects or high intensity objects
4. Single color object such as a white wall or fine
felt
5. No centre objects and sloping objects
6. Far and near objects on the screen
●Electronic Zoom (EL-ZOOM)
The electronic zoom magnifies a scene 5 times. With a
10-time optical zoom lens, the camera is capable of 50-
time zoom.
1. Move the cursor to EL-ZOOM and select ON or
OFF by moving the joystick to the right or left, and
then press the CAM (SET) key.
The factory default setting is ON.
ON:5-time electronic zoom is available with the
ZOOM switch on the controller.
OFF:The electronic zoom function is not used.
      **  ATW  **
R
B
RET••••|••••
-       +
••••|••••
-       +
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    AWC
→PUSH SET
AF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
      **  AWC  **
R
B
RET••••|••••
-       +
••••|••••
-       +
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O
      ** SET UP **
CAMERA ID    ON OALC/MANUAL   ALC OSHUTTER      OFF
AGC          ON(MID)
SYNC         INT
WHITE BAL    ATW 
OAF MODE      MANUAL
EL-ZOOM      ON
SENS UP      OFF
MOTION DET   OFF
RET     SPECIAL 
O