Panasonic Wv Ns324 Operating Instructions Manual
Have a look at the manual Panasonic Wv Ns324 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 54
-55-
■Transferring Picture Files
•Set FTP setup menu.
•Pre- and post-alarm picture files can be sent to and
stored on a designated FTP server.
•A picture file attached to a mail can be sent to the
specified mail addresses.
Note:When many alarm events arise at the same time,
it may happen occasionally that a mail is sent with-
out an alarm picture attached.
■Canceling Alarm Display
1. Indicating ALARM in the top window or in the
Camera Control window:
•Click the [Setup Menu] or [Alarm List] button.
2....](http://img.usermanuals.tech/thumb/58/68514/w64_wv-ns324_en_om_d-53.png "Page 54
-55-
■Transferring Picture Files
•Set FTP setup menu.
•Pre- and post-alarm picture files can be sent to and
stored on a designated FTP server.
•A picture file attached to a mail can be sent to the
specified mail addresses.
Note:When many alarm events arise at the same time,
it may happen occasionally that a mail is sent with-
out an alarm picture attached.
■Canceling Alarm Display
1. Indicating ALARM in the top window or in the
Camera Control window:
•Click the [Setup Menu] or [Alarm List] button.
2....")
![Page 55
-56- 5. Move the cursor to MASK SET, and click the [SET]
button.
The detection map is split into 48 areas with status
indications for each.
Transparency:Indicates a non-masked area that
has been incorporated into the detection area.
Blink:Indicates a non-masked area when the
cursor is on it.
Highlight:Indicates a masked area that has
been exempted from detection.
Stripe:Indicates an already masked area
when the cursor is on it.
6. Move the cursor to an area, and click the [SET]
button.
•The area will...](http://img.usermanuals.tech/thumb/58/68514/w64_wv-ns324_en_om_d-54.png "Page 55
-56- 5. Move the cursor to MASK SET, and click the [SET]
button.
The detection map is split into 48 areas with status
indications for each.
Transparency:Indicates a non-masked area that
has been incorporated into the detection area.
Blink:Indicates a non-masked area when the
cursor is on it.
Highlight:Indicates a masked area that has
been exempted from detection.
Stripe:Indicates an already masked area
when the cursor is on it.
6. Move the cursor to an area, and click the [SET]
button.
•The area will...")
![Page 56
-57-
■Reviewing Alarm Pictures
The alarm pictures stored in the camera can be
reviewed on the PC.
1. In the main window, click the [Alarm List] button.
2. Click the pertinent Data/Time in the list.
You can confirm the pictures of past alarm events.
Type TRM1: Alarm through Terminal 1
TRM2: Alarm through Terminal 2
VMD: Alarm through Video Motion
Detector
1: One alarm event picture attached
: More than one alarm event pic-
ture attached
3. The selected picture is displayed, and the alarm
image control...](http://img.usermanuals.tech/thumb/58/68514/w64_wv-ns324_en_om_d-55.png "Page 56
-57-
■Reviewing Alarm Pictures
The alarm pictures stored in the camera can be
reviewed on the PC.
1. In the main window, click the [Alarm List] button.
2. Click the pertinent Data/Time in the list.
You can confirm the pictures of past alarm events.
Type TRM1: Alarm through Terminal 1
TRM2: Alarm through Terminal 2
VMD: Alarm through Video Motion
Detector
1: One alarm event picture attached
: More than one alarm event pic-
ture attached
3. The selected picture is displayed, and the alarm
image control...")
![Page 57
-58-
■Resetting Alarm
You can reset the alarm output functions being activat-
ed.
1. In the main window, click the [Setup Menu] button.
2. Click the [Alarm] button to open the Alarm Setup
window.
3. Find External Alarm Reset in the window.
4. Click the [Alarm Reset] button.
5. Click the [Go to Main Menu] button to go back to
the main window.How to customize contents of e-mail notification
You can customize the contents of e-mails notifying the
recipient of alarm events and their dates.
Take the...](http://img.usermanuals.tech/thumb/58/68514/w64_wv-ns324_en_om_d-56.png "Page 57
-58-
■Resetting Alarm
You can reset the alarm output functions being activat-
ed.
1. In the main window, click the [Setup Menu] button.
2. Click the [Alarm] button to open the Alarm Setup
window.
3. Find External Alarm Reset in the window.
4. Click the [Alarm Reset] button.
5. Click the [Go to Main Menu] button to go back to
the main window.How to customize contents of e-mail notification
You can customize the contents of e-mails notifying the
recipient of alarm events and their dates.
Take the...")
![Page 63
Selecting a PRESET position From #1 to #16
#1 [1] + [CAM FUNC]
#16 [1] + [6] + [CAM FUNC]
AUTO PAN
ON [6] + [5] + [CAM FUNC]
OFF [6] + [6] + [CAM FUNC]
Speed Up [6] + [7] + [CAM FUNC]
Speed Down [6] + [8] + [CAM FUNC]
Setting Start Point [6] + [9] + [CAM FUNC]
Setting End Point [7] + [0] + [CAM FUNC]
Setting PAN Reverse [7] + [4] + [CAM FUNC]
ENDLESS PAN
On [7] + [6] + [CAM FUNC]
Off [7] + [7] + [CAM FUNC]
BLC
On [8] + [4] + [CAM FUNC]
Off [8] + [5] + [CAM FUNC]
AUTO FOCUS
AUTO [8] + [6] + [CAM FUNC]...](http://img.usermanuals.tech/thumb/58/68514/w64_wv-ns324_en_om_d-62.png "Page 63
Selecting a PRESET position From #1 to #16
#1 [1] + [CAM FUNC]
#16 [1] + [6] + [CAM FUNC]
AUTO PAN
ON [6] + [5] + [CAM FUNC]
OFF [6] + [6] + [CAM FUNC]
Speed Up [6] + [7] + [CAM FUNC]
Speed Down [6] + [8] + [CAM FUNC]
Setting Start Point [6] + [9] + [CAM FUNC]
Setting End Point [7] + [0] + [CAM FUNC]
Setting PAN Reverse [7] + [4] + [CAM FUNC]
ENDLESS PAN
On [7] + [6] + [CAM FUNC]
Off [7] + [7] + [CAM FUNC]
BLC
On [8] + [4] + [CAM FUNC]
Off [8] + [5] + [CAM FUNC]
AUTO FOCUS
AUTO [8] + [6] + [CAM FUNC]...")
max. 4 times, AUTO/FIX ON/OFF (SETUP MENU) selectable 1/60 (OFF), 1/100, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s 16 V DC 100 mA, Low-active Internet Explorer 5.01 SP2, 5.5, 5.5 SP2, 6.0, or Netscape Communicator 4.73, 4.78 Image resolution -62- When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming. PREVENTION OF BLOOMING AND SMEAR SPECIFICATIONS AGC BLC Electronic shutterON (LOW)/ON (MID)/ON (HIGH)/OFF SENS UP Auto focus ALARM OUT, AUX OUTMANUAL/AUTO OFF/AUTO PAN ON/OFF preset ID, camera ID, characters ON/OFF ON/OFF Auto mode Flip-A-chip Camera ID MOTION DET Cleaning 2 INPUT (ALARM IN 1-2), Low-active ALARM IN Camera Section Effective pixels 3.65 mm (H) x 2,71 mm (V), 1/4 768 (H) x 494 (V) 15,734 kHz internal/line-lock / multiplexed vertical drive (VD2) 59.94 Hz 1.0 V[p-p] NTSC composite/75 Ω more than 480 lines at center more than 350 lines at center 50 dB (AGC OFF, weight on) 1.0 lx (0.1 foot-candle) (AGC ON HIGH) Scanning area Synchronization Horizontal scanning fre- quency Vertical scanning frequency Video output Horizontal resolution Vertical resolution Signal-to-noise ratio Minimum illumination 640x480, 640x240, 320x240, 160x120 pixel JPEG (Super Fine/Fine/Normal/Low image quality selectable) Fast/Middle/Slow/Very Slow 32 kbps, 64 kbps, 128 kbps, 256 kbps, 512 kbps, 1 024 kbps, Unlimited TCP/IP, UDP/IP, HTTP, FTP, SMTP, DNS, DDNS, DHCP, ARP, BOOTP, NTP Windows 98 SE, Windows NT WORKSTATION 4.0 Service Pack6a, Windows 2000 Professional Service Pack2, Windows ME, or Windows XP Network Section Image process Image refreshing rate Traffic control Protocols supported OS applicable Applicable browsers Bright object Smear
-63- Panning range Zoom ratio Focus speed Focal lengthx10 + digital zoom x 5 approx. 3.8 s (TELE/WIDE) in manual mode approx. 3.0 s (FAR/NEAR) in manual mode automatic (open/close is possible)/manual 1 : 1.4 (WIDE) to 2.0 (TELE) 4.2 to 42 mm 4.9 ° to 48 ° 3.7 ° to 36 ° Zoom speed Iris Maximum aperture ratio Angular field of viewH V Lens/Mechanism sections Power source Dimensions24 V AC, 60 Hz 120 (D) x 196 (H) mm (4-3/4 (D) x 7-3/4 (H)) approx. 1.5 kg(3.3 lbs) –10 °C to +50 °C (14 °F to 122 °F) 15 W Power consumption Ambient operating temperature Weight Controls Weights and dimensions indicated are approximate. Specifications are subject to change without notice.360 ° endless possible (in auto-pan mode) manual/auto pan manual : approx. 1.0 °/s to 100 °/s, 8-steps/64-steps preset position : maximum approx. 100 °/s 0°to 92 ° manual manual : approx. 1.0 °/s to 100 °/s, 8-steps/64-steps preset position : maximum approx. 100 °/s pan/tilt, lens, 16 preset positions, home position Panning angle setting Panning mode Panning speed Tilting range Tilting mode Tilting speed Decoration cover ................................................................... 1 pc. Connector for 24 V AC .......................................................... 1 pc. RJ-45 female-female conversion connector .......................... 1 pc. CD-ROM (PDF Manual Contained) ....................................... 1 pc. ACCESSORIES Dome cover (approx. 60 % smoked type) .................................................... WV-CS2SE Dome cover (approx. 50 % smoked type) .................................................... WV-CS2SHE Dome cover (approx. 70 % metal type) ........................................................ WV-CS2ME Ceiling mounting bracket .............................................................................. WV-Q105/WV-Q106/WV-Q107A Wall mounting bracket ................................................................................... WV-Q108A OPTIONAL ACCESSORIES
Selecting a PRESET position From #1 to #16 #1 [1] + [CAM FUNC] #16 [1] + [6] + [CAM FUNC] AUTO PAN ON [6] + [5] + [CAM FUNC] OFF [6] + [6] + [CAM FUNC] Speed Up [6] + [7] + [CAM FUNC] Speed Down [6] + [8] + [CAM FUNC] Setting Start Point [6] + [9] + [CAM FUNC] Setting End Point [7] + [0] + [CAM FUNC] Setting PAN Reverse [7] + [4] + [CAM FUNC] ENDLESS PAN On [7] + [6] + [CAM FUNC] Off [7] + [7] + [CAM FUNC] BLC On [8] + [4] + [CAM FUNC] Off [8] + [5] + [CAM FUNC] AUTO FOCUS AUTO [8] + [6] + [CAM FUNC] MANUAL [8] + [7] + [CAM FUNC] AF On (Activate) [8] + [8] + [CAM FUNC] HOME POSITION Move to HOME [8] + [9] + [CAM FUNC] CAMERA ID On [9] + [3] + [CAM FUNC] Off [9] + [4] + [CAM FUNC] EL-ZOOM On [9] + [8] + [CAM FUNC] Off [9] + [9] + [CAM FUNC] RESTART Begin [1] + [0] + [0] + [CAM FUNC]Memorize PRESET From #1 to #16 Position #1 [1] + [0] + [1] + [CAM FUNC] Position #16 [1] + [1] + [6] + [CAM FUNC] IRIS Open [1] + [6] + [9] + [CAM FUNC] Close [1] + [7] + [0] + [CAM FUNC] EL-SHUTTER On [1] + [7] + [1] + [CAM FUNC] Off [1] + [7] + [2] + [CAM FUNC] Speed Up [1] + [7] + [3] + [CAM FUNC] Speed Down [1] + [7] + [4] + [CAM FUNC] AGC On [1] + [7] + [5] + [CAM FUNC] Off [1] + [7] + [6] + [CAM FUNC] SENS UP On [1] + [7] + [7] + [CAM FUNC] Off [1] + [7] + [8] + [CAM FUNC] Up [1] + [7] + [9] + [CAM FUNC] Down [1] + [8] + [0] + [CAM FUNC] SENS UP AUTO On [1] + [8] + [1] + [CAM FUNC] Off [1] + [8] + [2] + [CAM FUNC] Up [1] + [8] + [3] + [CAM FUNC] Down [1] + [8] + [4] + [CAM FUNC] LL SYNC phase INC [1] + [8] + [5] + [CAM FUNC] DEC [1] + [8] + [6] + [CAM FUNC] PAN 180 ° turn [1] + [8] + [7] + [CAM FUNC] CLEANING On [1] + [8] + [8] + [CAM FUNC] Off [1] + [8] + [9] + [CAM FUNC] Function Key Function Key -64- Shortcuts Shortcut operations are available to controllers having the CAM FUNCTION key. Entering from one to three digits using the numeric key(s) and pressing the CAM FUNCTION key will create a shortcut to the respective functions. The CAM FUNCTION key is abbreviated as [CAM FUNC] in the table below. APPENDIX Notes: •Actual operation takes place when the conditions for the changed settings are met. •Shortcuts may be ignored while PAN/TILT, ZOOM or FOCUS is in operation.
N0303-0 3TR001552BAB Printed in Japan PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC. San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809)750-4300Panasonic Digital Communications & Security Company Unit of Matsushita Electric Corporation of America Security Systems Group www.panasonic.com/cctv Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Zone Office Eastern:One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Central:1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205 Western:6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.