Panasonic Video Multiplexer Wj Fs616 Operating Instructions

-49-
OPERATING PROCEDURES (with WV-CU550A)
Direction Arrow Button
LEFT
RIGHT UP
DOWNHOME/SET
Joystick Controller
LEFT RIGHTUP
DOWN
Camera Selection Buttons
4
8
12
16
3
7
11
15
2
6
10
14
1
5
9
13
CAMERA/PRESET   POSITION
Numeric Key + Set Key
123
456
789
MON CAM
UNIT/ESC0
SET
F3F4F2F1
U01   C01_MLT ∗SPOT _ SEQ _VCR
123
456
789
MO N C A M
UNIT/ESC SET0
When operating the Video Multiplexer with the WV-
CU550A System Controller, the following buttons and
keys of the System Controller correspond with those...

-50-
FOCUS
NEAR
FARAF
ZOOM
TELE
WIDE
CLOSE OPENIRIS
PRE-
POSI
123
456
789
MO N C A M
UNIT/ESC SET0
AUTO/+
AUX2
CAMERA CONTROL 
FUNCTION
Camera control is only available while the camera
picture is displayed in Single Spot on the monitor
screen.
Note:When controlling the camera with multiplexed
control data by connecting a coaxial cable, you
should install the optional WV-PB6164 Data
Multiplex Board in the Video Multiplexer.
Camera Selection
1. Set the LCD display to ✴SPOTor ✴MLT by repeat-
edly pressing...

-51-
F3F4F2F1
U01 C01 CamSet Up
RES A.RES
HOME/–
AUX1
T/L MODE
SET UP
PLAY REV
CAMERA
SET ONCAMERA
SET OFF
ALTHOME/–
AUX1AUX2
AUTO/+
Note:The auxiliary control is not available while
operating the zoom or pan/tilt head.
3. Select an item by moving the joystick UP or DOWN.
Then select the mode by moving the joystick LEFT
or RIGHT.
4. Press the SETkey to execute the setting or enter a
sub menu.
5. To return to the previous menu, press the UNITkey.
6. Press the F3button to reset the selected function,
or...

-52-
SYSTEM EXPANSION
The system shown below is an example of the expansion capabilities of the WJ-FS616 Video Multiplexer. Up to four Video
Multiplexers can be connected to expand the camera inputs.
481216
371115
261014
15913
PUSH   OPEN16POWERLOCKON
OFF
ALARMMULTI
SCREENMULTISCREENSELECT
RESET SPOT SEQUENCE
VCR
CAMCAMERA/PRESET   P O S I T I O N
Video
Data RS-485
Spot In
Time Lapse VCR
System Controller
WV-CU550A
Spot Monitor
Live
Main: 1-16ch
Local: 1-16chMultiscreen Monitor
Live 1-16ch
Playback...

-53-For example, press the keys shown below.
In this example, the picture of Camera No. 15 con-
nected to Video Multiplexer Unit 2 is displayed on
the Spot Monitor connected to Video Multiplexer
Unit 1.
5. Operate the selected unit as described in the
OPERATING PROCEDURES.
6. Select another unit with the Numeric Keys. Then
press the UNIT/ESCkey to activate the selected
unit.
Other Applications
•Application 1
The video signal looped through the SPOT IN con-
nector can be displayed on the Spot Monitor.
1....

-54-
Local Site
Confirm that the REC MODE SETUP on the REC
OUTPUT SETUP menu (page 28) is set to MODE 0.
If another mode is set for the REC MODE SETUP,
this application does not work properly.
Main Site
To display the camera pictures in the Local Site,
operate the video multiplexer as displaying the
playback picture.
However same functions are enabled displaying the
playback picture.
•Application 2
The camera pictures in the Local Site can be dis-
played on the Multiscreen Monitor in the Main Site
by...

(02H)   (      ) – – – – – –  (      )   (3AH)   (      ) – – – (      )     (03H)
[STX]     [Transmission Command]     [:]     [Error Code]     [ETX]
[STX]   [Address] [;]   [Transmission Command]   [ETX] Code
-55-
APPENDIX
ASCII (02H)   (      ) – – – – – – – – – – – – – – – – – (      )   (03H)
[NAK]   [e] Code
ASCII (15H)
This Appendix details the elements for communication between the Video Multiplexer and the personal computer. For
BAUD RATE, DATA BIT, STOP BIT and PARITY settings, see page 35 COM...

m=0Quad m=1 7 divide
m=2 9 divide m=3 10 divide
m=4 13 divide   m=5 16 divide
m=
1No. of divisions (+)m=DNo. of divisions (−)
Item Item
m=0
Manual Reset
m=1 Auto Reset
-56-mm=00 - 16   Camera Number
*00=Spot Input
mm=01 - 16   Playback CH number
Alarm InputResponse
Command (ASCII)
Command Table
(1) Operation Control
Transmission
Command (ASCII)Parameter (ASCII)
Monitor Select OMS : m OMSm=0
Spot Monitor
m=1 Multiscreen Monitor
m=2 Multiscreen 2 Monitor
VCR/Camera Select OVC : m OVCm=0
Camera Mode
m=1...

Item
Item
Response
Command (ASCII) Transmission
Command (ASCII)Parameter (ASCII) DCR : mm mm=UU       Move Upward
mm=DD       Move Downward
mm=RR       Move to Right
mm=LL        Move to Left
mm=BB       Move to lower layer
mm=ES       Move to upper layer
Item decision (partial)
mm=IC        Select parameter (+)
mm=DC       Select parameter (–)
mm=FF        Select page
mm=UR       Move to Upper-Right
mm=UL       Move to Upper-Left
mm=DR       Move to Lower-Right
mm=DL       Move to Lower-Left
*2 DCR
-57-...

No.
-58- Examples of response
Response Command (ASCII) Main Unit Information
1 @mPLSNcc Single Spot (Camera)
2 @mPLSZcc Single Spot + Electronic Zoom (Camera)
3 @mPLSScc Single Spot + Still (Camera)
4 @mPLSXcc Single Spot + Zoom + Still (Camera)
5 @mPLSMLa Multi Spot (+ Still) (Camera)
6 @mPLQNcc Spot Sequence (Camera)
7 @mPLQMLa Multi Sequence (Camera)
8 @mPLQZcc Spot Sequence + Zoom (Camera)
9 @mPVSNcc Single Spot (VCR)
10 @mPVSZcc Single Spot + Zoom (VCR)
11 @mPVSScc Single Spot + Still (VCR)
12...