Panasonic Video Multiplexer Wj Fs616 Operating Instructions

-9- 16. Function Button (FUNCTION)
This button is used to display the VCR playback
picture with the camera pictures on the multiscreen
monitor.
During the setup, this button is used to select the
next page.
17. Auto/Increment Button (AUTO / + )
This button is used to activate the auto panning
function.
During the setup, this button is used to select the
desired parameter in the setup menu.
18. Home/Decrement Button (HOME / – )
This button is used to move the camera to the home
position.
During the setup,...

-10-
INSTALLATIONS
The installations described below should be made
by qualified service personnel or system installers.
Installing the WV-PB6164 Data Multiplex
Boards
When controlling the camera with the multiplexed
control data by connecting a coaxial cable, the WV-
PB6164 Data Multiplex Board must be installed  in
the Video Multiplexer.
Four data multiplex boards are included with the
WJ-FS616 for cameras 1 to 4.
Please note that additional multiplex boards are
available for purchase as model...

-11-
CH9 - CH16
CH1 - CH8 6. Set the jumper connector, located at the top left of
the board to be installed, to the position shown
below.
7. Insert the board and confirm that the position is cor-
rect. Then push it in straight.
8. After installing the boards, secure them by tighten-
ing the screws and knobs shown above.
Note:Some settings for the VD2 signal and control
data will be necessary from the setup menu of
the Video Multiplexer. Refer to Cable Compen-
sation/VD2/Data Setup on page 34 for...

-12-
Dip Switch Setting
Alarm Output Setting
1. Disassemble the video multiplexer as described for
installing the Data Multiplex Boards on page 10.
2. Set switches (SW3/SW4/SW5) on the board to
choose the alarm control signals as either Open
Collector (O.C) or Pulse (0/5V).
Open Collector (O.C): 16V DC 100 mA max.
Pulse (0/5V): +5V DC approx. 500 ms
The above switch positions are the initial factory
settings.
0/5V O.C
SW5
0/5V 0/5VSW3
O.CSW4
O.C
SW3 :  Alarm Output
SW4 :  Alarm Reset Output
SW5 :...

-13-
WV-CU550A System Controller
Modifying the Front Panel
1. Peel the tape off the supplied panel templates, then
attach them on the front panel of the System
Controller.
2. Peel off the label and attach it on the rear of the
System Controller as shown below.
CONTROLLER
ON MODE
OFFINOUTTERMON OFF
DATA0123456789CONTROLLER
UNIT NO.
1-8
Connection with
Video Multiplexer
(WJ-FS616)TERM. MODEON OFF0OFF
ON
WJ-FS616 Video Multiplexer
Mounting in the Rack
1. Remove the four rubber feet by removing the four...

-14-
Basic System Connection
SYSTEM CONNECTIONS
481216
371115
261014
15913
PUSH   OPEN16
POWERLOCKON
OFF
ALARMMULTI
SCREENMULTISCREENSELECT
RESET SPOT SEQUENCE
VCR
CAMCAMERA/PRESET   POSITION
Video
Data RS-485
Video Multiplexer
WJ-FS616
Time Lapse VCR
Personal Computer
(Software) System Controller
WV-CU550ASpot Monitor
Live 1-16chMultiscreen Monitor
Live 1-16ch
Playback 1-16ch RS-232C/WiredAlarm Sensor
AUXAlarm
123456789MON CAM0System Controller for WJ-FS616
F3F4F2F1
Shown below is an example of a basic...

-15-
CAMERA
IN
CAMERA
OUT  16 15 14 13 5 4 3 2 1
16 15 14 13 5 4 3 2 1
A    B
TA    B
RG
N
DG
N
D
RS485
AUXAlarm
Video Multiplexer WJ-FS616
Connection with the Camera Sites
Connect cameras (or camera site equipment) data
multiplexed type to the CAMERA IN connectors 1
through 4 on the rear panel of the Video Multiplex-
er.
Note:Make sure that the cable length between the
camera site and the WJ-FS616 Video Multi-plex-
er is less than 900 m (3 000 ft) when using RG-
59/U, BELDEN 9259 or equivalent cables....

-16-
Connections  for RS-485 type camera
There are two options  to connect the camera with
the Multiplexer, depending on the distance
between them. 
For data multiplexed type cameras, a maximum dis-
tance of 900 meters (3 000 ft) is the limit for using
coaxial cable such as RG-59/U, BELDEN 9259 or
equivalent.
If more distance is required, use cameras and
Multiplexers with RS-485 communication feature.
This will lower signal loss and extend the distance
as video signal and data are transmitted...

-17-
Connection with the Monitors
Connect the Monitors to the Spot Output (SPOT
OUT) Connector and Multiscreen (MULTISCREEN)
Connector on the rear of the Video Multiplexer.
Connection with the WV-CU550A
System Controller
If the supplied 6-conductor cable assembly is used,
simply plug one end of the cable into the DATA IN
port of the Video Multiplexer and the other end into
DATA OUT port on the System Controller.
If you use cables assembled from locally procured
materials, it is important that only high...

-18-
Connection with Alarm Sensors
Connect the sensor switches to the Alarm/Remote (ALARM/REMOTE) Control Connector on the rear of the Video
Multiplexer as shown in the example below.
37
19
20 1
SW2
SW1
SW16
GND
ALARM/REMOTE1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19Function
Electronic Zoom
Sequence
Spot
Alarm/Remote Select Input
Sequence SW for Spot Output
Not Used
Alarm Recover Input
Alarm Output
Alarm 16
Alarm 14
Ground
Alarm 11
Alarm 9
Alarm 8
Alarm 6
Ground
Alarm 3
Alarm 1 Pin No....