Panasonic Video Multiplexer Wj Fs616 Operating Instructions

-19-
Connection with the Time Lapse VCR
Connect the Time Lapse VCR as shown in the example below.
19
201
ALARM/REMOTE
37
CAMERA
SW  INREC  OUT PLAY   IN
VIDEO S–VIDEO S–VIDEO VIDEO
VIDEO IN
CAMERA
SW  OUTGND
S-VIDEO
AUDIOVIDEO OUT
12345678910111213141516
8 9
28 26
13 4 7 16
1234
ALARM
IN
COMALARM
RESET INALARMRECOVER OUT
5678
ALARM
OUT
1 SHOT IN
TAPE END
OUT
9101112
WARNING
OUT
HUMID OUT
REC REVIEWOUT
13141516
SERIES
REC IN
TIME
ADJUST INTIMEADJUST OUT
COMREC OUT
SERIES
REC OUT
Video Multiplexer...

-20-
Connection with External Remote Control Switches
Connect the switches (dry contact or open collector input) to the Alarm/Remote (ALARM/REMOTE) Control Connector
on the rear of the Video Multiplexer as shown in the example below.
37
19
20 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19Function
Electronic Zoom
Sequence
Spot 
Alarm/Remote Select Input
Sequence SW for Spot Output
Not Used
Alarm Recover Input
Alarm Output
Camera 16
Camera 14
Ground
Camera 11
Camera 9
Camera 8
Camera 6
Ground
Camera 3...

-21- The Setup Menu provides a way for controlling func-
tions not available through direct input.
Displaying the SETUP MENU
1. Confirm the camera and peripherals are connected
correctly and securely.
2. Turn on the power switches of all system compo-
nents.
3. Press the SETUP/ESCbutton for 2 seconds. 
The SETUP MENU appears on the Spot and
Multiscreen Monitors as shown below.
SETUP MENU
        WJ-FS616 SETUP MENU
        ALARM SETUP *
        MULTI OUTPUT SETUP *
        SPOT OUTPUT SETUP *...

-22-
SETUP MENU
Alarm SetupAlarm Recall
Alarm Schedule
Camera Site Alarm
Camera Switching Signal Loss Alarm
Alarm Display on the Monitors
Alarm Output Duration
Alarm Buzzer Duration
Alarm Mode on Multiscreen Monitor
Camera Upload
All Reset
Page 23
Alarm Mode on Spot Monitor
Dynamic Recording
Alarm Recording Mode
Camera Title Display
Clock Display
Still Display
Border Display
Camera Display Position
Sequence Mode
Camera Title Display
Clock Display
Camera Title Display
Clock Display
Dynamic Recording...

-23-
Alarm Setup Menu
Move the cursor to ALARM SETUP on the SETUP
MENU, then press the SET button. The ALARM
SETUP menu appears on the monitor screen as
shown below.
1. Alarm Recall
There are 100 alarm records  stored in chronologi-
cal order in 10 pages of table.
The tables also indicate the alarm mode.
1. Move the cursor to ALM RECALL and press the
SET button. The ALARM RECALL table appears
on the monitor screen as shown below.4. To clear the alarm data, press the LEFT or
RIGHT button to select  CLEAR...

-24-
7. Alarm Buzzer Duration
This item lets you select the ringing duration of the
alarm buzzer when alarm is activated.
1. Move the cursor to the ALM BUZZER DUR
parameter.
2. Select the desired duration by pressing the
LEFT or RIGHT button. The initial factory setting
is 2 SEC.
OFF:Disables the alarm buzzer output.
1SEC - 5 MIN:Selects a buzzer duration
between 1 second and 5 minutes.
EXT:The alarm buzzer continues to beep until
the ALARM RESET button is pressed, or an
external alarm recover signal is...

-25-
9. Alarm Mode on Spot Monitor
This item lets you select the mode for displaying an
alarm on the Spot Monitor.
1. Move the cursor to the ALM MODE-SPT para-
meter.
2. Select the desired mode by pressing the LEFT
or RIGHT button. The initial factory setting is
ALM-SPOT mode.
ALM-SPOT:The picture of the camera that has
activated the alarm is displayed.
If multiple alarms are activated, the monitor
displays the camera picture that has acti-
vated the alarm most recent.
ALM-IGNORE:Displays the title of...

-26-
2. Clock Display Setting
This item lets you enable or disable the clock dis-
play on the Multiscreen Monitor.
1. Move the cursor to the CLOCK DISPLAY para-
meter.
2. Select ON or OFF by pressing the LEFT or
RIGHT button. The initial factory setting is ON.
ON:Enables clock display on the monitor
screen.
OFF:Disables clock display on the monitor
screen.
3. Still Display
This item lets you enable or disable display of the
subtitle “STIL L” on the Multiscreen Monitor when
the channel is in the still...

-27- Move the cursor to SPOT OUTPUT SETUP on the
SETUP MENU, then press the SET button. The SPOT
OUTPUT SETUP menu appears on the monitor
screen as shown below.
These items let you determine the display mode of
the Spot Monitor.
           SPOT OUTPUT SETUP
        TITLE DISPLAY  ON
        CLOCK DISPLAY  ON
1. Camera Title Display
This item lets you enable or disable display of the
camera title on the Spot Monitor.
1. Move the cursor to the TITLE DISPLAY parame-
ter.
2. Select ON or OFF by pressing the...

-28-
2. Clock Display
This item lets you enable or disable recording of the
clock display on the VCR.
1. Move the cursor to the CLOCK DISPLAY para-
meter.
2. Select ON or OFF by pressing the LEFT or
RIGHT button. The initial factory setting is ON.
ON:Enables recording of clock display on the
VCR.
OFF:Disables recording of clock display on the
VCR.
3. Dynamic Recording
This item lets you select the cameras for dynamic
recording mode in non-alarm condition.
If five or more cameras are connected to the...