Panasonic Video Multiplexer Wj Fs616 Operating Instructions

Video Multiplexer
WJ-FS616
Before attempting to connect or operate this product, please read these instructions completely 

Warning:
This equipment generates and uses radio frequency ener-
gy and if not installed and used properly, i.e., in strict
accordance with the instruction manual, may cause harmful
interference to radio communications.    It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of Part 15 of FCC Rules,
which are designed to provide reasonable protection
against such interference when operated in a commercial
environment.
WARNING:
TO PREVENT FIRE OR...

-1- The WJ-FS616 Video Multiplexer is designed to multi-
plex the field signals from video cameras and record
the camera images on a time lapse VCR. Up to 16
cameras can be connected to the unit for monitoring
images in multiscreen, sequence, still or electronic
zoom mode on a video monitor screen.The WJ-FS616 allows you to control camera functions
such as lens focussing, zooming, and iris, positioning
of the pan/tilt head, etc. This makes the system highly
flexible and sophisticated, and allows...

-2- • Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not block the ventilation opening or slots on
the cover.
To prevent the appliance temperature from rising,
place the appliance at least 5 cm (2 inches) away
from the wall.
• Do not drop metallic parts through slots. 
This could permanently damage the appliance. Turn
the power off immediately and refer servicing to
qualified service personnel.
• Do not attempt to disassemble the...

-3-
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
4
8
12
16
3
7
11
15
2
6
10
14
1
5
9
13
PUSH   OPEN
16
POWERLOCK
ON
OFF
ALARMMULTI
SCREENMULTISCREENSELECT
RESETSPOT SEQUENCE
VCR
CAMCAMERA/PRESET   P OSITION
FUNCTION
PRE-POSILEFT
RIGHT
AUTO UP
DOWN
HOME/SET
EL-ZOOMSTILL
 CURSOR / CAMERA   CONTOROLCLOSEOPENIRIS
NEAR FARFOCUS
TELEWIDEZOOM
LOCKOFF ONSET  UP/ESC
VCR   CONTROL
T/L   MODE
//
Video Multiplexer WJ-FS616

1. Power Switch (POWER ON / OFF)
This switch turns the power of the video multiplexer
on or...

21. Function Button (FUNCTION)
This button is used to display the VCR playback
picture with the camera pictures on the multiscreen
monitor.
During the setup, this button is used to select the
next page.
22. Preset Position Button (PRE-POSI)
This button is used to assign a preset position to a
specified camera.
23. Still Button (STILL)
Increment Button (+)
This button is used to still the picture displayed on
the multiscreen monitor.
The LED (Green) in the button lights up to indicate
that the still mode...

-5-33. VCR Control Buttons
These buttons are used for remote control of the
VCR that is connected to the Video Multiplexer.
The buttons function as shown below.
: Rewind
: Pause
: Fast Forward
: Reverse Play
: Stop
: Play
: Decreases recording duration
: Increases recording duration
: Record
/
/
30. Zoom Control Buttons (ZOOM, TELE / WIDE)
These buttons are used to adjust the lens zoom of
the specified lens mounted on the camera.
31. Setup/Escape Button (SETUP / ESC)
This button is used to display the...

-6- 49. Record Output Connector (REC OUT, VIDEO / 
S-VIDEO)
The recording signal for the time lapse VCR is pro-
vided via this connector.
This connector can also be used as multiscreen out-
put 2 with the specified conditions.
50. Playback Input Connector (PLAY IN, VIDEO /
S-VIDEO)
The playback signal from the time lapse VCR is sup-
plied to this connector.
51. Multiscreen Output Connector (MULTISCREEN
OUT)
The video output signal for the multiscreen monitor
is provided via this connector
52. RS-232C...

-7-
System Controller WV-CU550A
Note:When using this controller in combination with the WJ-FS616, cover the panel of the controller with the panel tem-
plates provided.
123
456
789
MO N C A M
UNIT/ESC0
RESETEL-
ZOOMMULTISCREEN
SELECT
FUNCTIONPRE-
POSI STILL
HOME/–  AUTO/+CLOSE OPENIRIS
AFFOCUS
NEAR ZOOM
TELE
FAR WIDE
System Controller for WJ-FS616
LEFT RIGHTUP
DOWN
ALARMBUSY
F3F4F2F1
CONTROLLER
ON OFFINOUTTERM.ON OFF
DATA
0123456789
CONTROLLER
UNIT NO.
1-8
T/L MODE
SET UP
PLAY REV
CAMERA
SET ONCAMERA...

-8- 1. Alarm Indicator (ALARM)
This LED indicator (Red) lights up to indicate that
an alarm condition exists.
It goes off when the alarm is reset automatically. 
To turn the indicator off, press the ALARM RESET
button.
2. Busy Indicator (BUSY)
This LED lights up to indicate that the system is
locked by PC command.
While this LED is lit, control from the video multi-
plexer and system controller is disabled.
3. Function Buttons (F1/F2/F3/F4)
These buttons are used to select functions dis-
played on the...