Panasonic Video Multiplexer Wj Fs616 Operating Instructions

-39-
1
32
41
32
4 SEGMENT SCREEN
45
7 SEGMENT SCREEN
67
1
4
72
5
83
6
9
9 SEGMENT SCREEN
12
3456
7
10 SEGMENT SCREEN
8910
123
45
6789
10
13 SEGMENT SCREEN
11 12 13
1234
5678
9 101112
13
16 SEGMENT SCREEN
14 15 16
ENTRANCE
ENTRANCE
EL-ZOOM
MULTISCREENSELECT
3. Electronic Zooming
1. Repeat the procedures described above for Single
Spot.
2. Press the EL-ZOOMbutton to display the zoomed
picture.
The LED on the EL-ZOOM button lights up.
3. Press the UP, DOWN, LEFTor RIGHTbutton to
move the picture in the...

-40-
ENTRANCE
STILL
Note:You can stilled multiple pictures on the multi-
screen.
5. Press the blinking CAMERA button to cancel the
Still function.
6. Press the STILL button again. The displayed pic-
tures returns to normal viewing.
The LED on the STILL button goes off.
6. Spot or Multi Sequence
1. Press the MULTISCREENbutton.  The LED (green)
on the button lights up.
2. Press the SEQUENCEbutton to activate the
sequence (SEQ1, SEQ2 or SEQ3) programmed.
The LED on the SEQUENCE button lights up.
Note:Refer...

-41-
4-SEGMENT
 SCREEN9-SEGMENT
 SCREEN16-SEGMENT
 SCREEN
1. Single Spot
1. Repeat steps 1 and 2 above.
2. Press the desired CAMERA button (1 - 16)corre-
sponding to the picture you want to display. The
selected playback picture is displayed on the moni-
tor screen.
Note:
•Blank channels are displayed in black.
•While playing back quad pictures, the corre-
sponding  4-segment picture is displayed, if the
selected number is recorded as part of the
quad picture. For instance, if #5 is selected, the
quad...

-42- Notes:
•This function is not available when S-VIDEO
playback input is used.
•To enable this function, connect with the VIDEO
playback input at the same time. The VIDEO
playback picture is displayed automatically
without making any setting changes.
6. To display another playback picture, press the
FUNCTIONbutton.
The LED on the button starts to blink. Select the
channel you want to display by pressing the corre-
sponding CAMERAbutton.
7. To return to the camera picture multiscreen, press
the...

-43-
CLOSE OPENIRIS
LEFT
RIGHT UP
DOWNHOME/SET
PRE-POSI
4. Press the IRISbuttons to close or open the lens iris.
Adjust the lens iris by using the buttons to obtain
the proper picture exposure.
By pressing both of these buttons at the same time,
the lens iris is reset to the initial factory settings.
2. Pan/Tilt Control (Manual Operation)
1. Select the desired camera referring to the Camera
Selection procedure described on page 42.
2. Press the Direction Arrow buttons to move the
pan/tilt head in the...

SET  UP/ESC
-44-
FUNCTION
LEFT
RIGHT UP
DOWNHOME/SET
3. Select the desired item by pressing the UPor
DOWNbutton. Then select the desired mode by
pressing the LEFTor RIGHTbutton.
4. Press the HOME/SETbutton to execute the setting
or enter a sub menu.
5. Press the LEFTand RIGHTbuttons simultaneously
to reset the selected menu.
6. Press the SETUP/ESCbutton to execute the setting
and return to the previous menu.
7. Press the SETUP/ESCbutton, while holding the
FUNCTIONbutton, to escape from the setup mode
or...

-45-
ALARM ALARM
ALARM ALARM
ALARM ALARM
ALARM ALARM
ALARM
ALARM ALARM
ALARM ALARM
ALARM ALARM
ALARM ALARM
[Spot]
[Quad Spot]
[Quad Sequence]
ALARM
2. Alarm Indication Mode
•The camera pictures selected before alarm was
activated remain on the monitor screen.
•If the alarmed channels are displayed, the camera
title and alarm display blink alternately on the moni-
tor screen.
Note:If the alarm channel is in the Still mode, it
returns to normal viewing.
Spot Output
1. Alarm Spot Mode
•The alarmed camera...

-46-
CH1
CH5
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH1 CH2
CH3 CH4
CH9 CH2
CH3 CH4
CH9 CH10
CH11 CH12
CH5 CH6
CH7 CH7
CH5 CH6
CH7 CH8
CH13 CH6
CH7 CH8 CH1 Alarmed
CH2 - CH4
Alarmed
CH5 Alarmed
CH6 - CH8
Alarmed
CH9 Alarmed
CH10 - CH13
Alarmed
Sequence Display
Sequence DisplaySequence Display
Multiscreen 2 Monitor Multiscreen Monitor
Auto Reset
The alarm is automatically reset after the pro-
grammed Alarm Output Time has elapsed or the lost
video signal has been recovered.
The ALARM indicator changes from...

-47-
RESETSPOT
Alarm Suspension
This function disables activation of the alarm link
and instead enables recording of any alarm activat-
ed in the alarm log.
It is used to suspend the alarm link during camera
setup.
1. Press the RESETand SPOTbuttons simultaneously
for more than two seconds to suspend the alarm.
The LED on the RESET button lights up.
2. Press the RESETbutton again to reset the alarm
suspension.
The LED on the RESET button goes off.
OTHER FUNCTIONS
Recording on the Time Lapse
VCR
The...

FUNCTION LEFT
RIGHT UP
DOWN
HOME/SET
SET  UP/ESC
LEFT
RIGHT UP
DOWNHOME/SET
SET  UP/ESC
EL-ZOOMSTILL
MO NCAM
UNIT/ESC
FUNCTION
HOME/–  AUTO/+ LEFT RIGHTUP
DOWN
AUX1AUX2
SET
SET UP
4
8
12
16
3
7
11
15
2
6
10
14
1
5
9
13
CAMERA/PRESET   POSITION
123
456
789
MON CAM
UNIT/ESC0
SET
-48-
SETUP MENU OPERATIONS (with WV-CU550A)
During setup of the WJ-FS616 with the WV-CU550A System Controller, the following buttons and keys of the System
Controller correspond with those of the WJ-FS616 as shown below.
Display...