Panasonic Vacuum Cleaner Mcug413 Operating Instructions

’b 26 ’b
Wand
Rallonge
Tu b o
C r e v i c e t o o l
S u c e u r p l a t
Herramienta
p a r a h e n d i d u r a s
Combination
Brush
B r o s s e m i x t e
C e p i l l o d e
combinacion
Hose
Tuyau
Manguera
M a i n u n i t
 When you have finished using the 
vacuum cleaner, replace the 
attachments in their storage 
positions.
 Place one wand back into the other,
as shown in the illustration to the
left.
 Replace the wands and crevice tool
aligning the markings on the
attachments with the markings on
the main...

’b 25 ’b
’b 32 ’b
Cleaning the Sub’bFilter
D u s t c o v e r
C o u v e r c l e d u l o g e m e n t d u
s a c à p o u s s i è r e
C u b i e r t a d e l a b o l s a
Subfilter
F i l t r e s e c o n d a i r e
F i l t r o s e c u n d a r i o
Clean the sub’bfilter when it becomes
dirty.
 Remove the dust cover.
 Remove the dust bag.
 Remove the sub’bfilter from the
vacuum cleaner.
 Gently clean the sub’bfilter with
water.
 Make sure that it is completely dry
and then re’binstall it into the
vacuum cleaner....

’b 24 ’b’b 33 ’b
H o s e c u f f
M a n c h o n d u t u y a u
C o l l a r d e l a m a n g u e r aWand
Rallonge
Tu b o
U p h o l s t e r y t o o l
P e t i t s u c e u r
H e r r a m i e n t a p a r a t e l a s C r e v i c e t o o l
S u c e u r p l a t
H e r r a m i e n t a p a r a e n d i d u r a s
D u s t i n g b r u s h
B r o s s e à é p o u s s e t e r
C e p i l l o p a r a s a c u d i r
C r e v i c e t o o l
S u c e u r p l a t
H e r r a m i e n t a p a r a e n d i d u r a s
To achieve maximum reach...

’b 23 ’b
’b 34 ’b
Clearing Blockages in the Suction Hose

Set the vacuum cleaner to the
upright position.
 Press in the side clips on the hose
cuff to remove it from the suction
inlet. Remove the blockage.
 Reattach the hose cuff to the
suction inlet, then operate the
vacuum cleaner to check that the
blockage has been properly
cleared. If the hose is still blocked,
the suction force will be weak.
CAUTION
Be sure to turn the ON/OFF switch to the "O" position and disconnect the power
cord from the...

’b 22 ’b’b 35 ’b

Disconnect the hose from the 
vacuum cleaner.
 Pull the hose gently in the direction 
of the arrow to disconnect it.
 Remove the wand and crevice tool 
from the vacuum cleaner.
 The wand contains another wand in 
it. Pull out the second wand.
 When removing the wand and 
crevice tool, pull them in the 
direction shown in the illustrations.
Note:  Pulling them straight back  from
the vacuum cleaner, or pulling them
forcefully, may damage the attachment
clamps.
Using Attachments
C r e v i...

’b 2’f ’b
Cleaning the agitator assembly
When threads get caught in the 
agitator assembly, clean the 
assembly.
 Remove threads caught in the
assembly by cutting them with
scissors.
Threads
Fils
Hilachas
Esta aspiradora se puede fijar de tres
posiciones. Vertical, Normal o
Paralelo. Ponga su pie en el cojIn en la
parte posterior izquierda del limpiador
y tire del mango hasta que se libere de
su posiciKn vertical.
PosiciKn vertical
 La manija se traba normalmente  adentro esta posiciKn para el...

’b 20 ’b’b 37 ’b
H a n d l e r e l e a s e p a d
P é d a l e d e d é g a g e m e n t
d u m a n c h e
P e d a l d e l i b e r a c i ó n
d e l m a n g o
Adjusting the Handle
The handle of this vacuum cleaner
can be set to one of three positions
Upright, Normal or Parallel.  Place
your foot on the pad at the left rear
of the cleaner and pull back on the
handle until it releases from its
upright position.
Legs
Pattes
Soporte
Upright position
  
The handle is normally locked in 
this position for storage or...

’b ’f9 ’b
’b 38 ’b
REPLACEMENT INSTRUCTIONS
Removing the Bottom Plate
Latch
Loquet
Sujetador M o u n t i n g s c r e w
Vi s d e m o n t a g e
To r n i l l o s u j e t a d o r
B o t t o m p l a t e
P l a q u e i n f é r i e u r e
P l a t e i n f e r i o r
Latch
Loquet
Sujetador
P u l l h e r e
Ti r e r i c i
J a l e a q u í
PULL
Press in clips
Presser sur les agrafes
Presionar las lenguetas
B o t t o m p l a t e
P l a q u e i n f é r i e u r e
P l a t e i n f e r i o r
Set the vacuum cleaner to the...

’b ’f8 ’b’b 39 ’b
NOTE: To reduce the risk of electrical shock, this v’2acuum cleaner has a polarized
plug, one blade is wider than the other. This plug will fit in a polarized outlet o’2nly
one way. If the plug does not fit fully in the o’2utlet, reverse the plug. If it still does no’2t
fit, contact a qualified electrician to install the proper outlet. DO NOT CHANGE’2 THE
PLUG IN ANY WAY.  Only use outlets near the floor.
Power Cord
 Set the ON/OFF switch to> ’2to 
operate the vacuum cleaner.
 Set the...

’b ’f7 ’b
’b 40 ’b

Remove the bottom plate.
 Pull the socket out of the bracket.
 When removing the lamp, be careful
not to pull on the headlight lamp
wiring.
 Remove the bulb by gently pushing
it in and turning counter clockwise.
 Push a new bulb gently into the
socket and turn it clockwise to
install it. Use a standard bayonet
base appliance bulb rated at ’f20V
20W Max.
 Slide the tab on the bulb socket into
the bracket at the front of the
nozzle.
 Reattach the bottom plate.
Replacing the Headlight...