Panasonic UF 8100 YC User Manual

							71
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4.2. Service Modes (For Facsimile)
Caution:
The factory default parameters are preset (country dependent) for optimum performance and in 
compliance with the local telecommunication regulations/standards, and do not need to be changed. 
Changing some of these parameters may cause the unit to be no longer compliant or become 
inoperable.
4.2.1. Fax Service Mode Procedure
1. To enter the Fax Service Mode
a. Press “FUNCTION” and then “7” keys.
b. Press “MONITOR” four times, then press “* (TONE)”.
c. Enter the desired code number or press the “V”, ”/\” arrow keys.
2. To exit the Fax Service Mode
Press “STOP” key.
Note:
The following buttons provide these functions in the Service Mode:
4.2.2. FAX Service Mode Table
The following service modes are provided to assist you in setting operational functions of the unit and 
determining the condition of the unit.START: : The new setting value is stored in the machine.
V” : Scroll the function parameter number down.
/ “ : Scroll the function parameter number up.
No. Service Mode Description
00 Not Used
01 Function Parameter Setting Allows changes to the function parameters (the home 
position, etc.).
02 RAM Edit ModeFactory use only.
03 Print  Parameter  List /  Report Prints the Function Parameter List, Page Memory Test, Printer 
Report, All Document File, Protocol Trace and Toner Order 
Form.
04 Modem Tests Generates various binary, tonal and DTMF signals, by the 
modem.
05 Not Used
06 RAM Initialize Initialize RAM and restore the default value of the function 
parameters.
Note: Turn the Power Switch to the OFF and back to the ON 
position to enable the parameter settings.
07 Not Used
08 Check & Call Allows input of information for Service Alert Report, 
Maintenance Alert Report and Toner Order Form.
09 System Maintenance Used for Firmware Update, Firmware Backup, Parameter 
Restore, Parameter Backup, Transferring Firmware from the 
PC to the Flash Card and Sending a Received File during a 
fatal printer error.
10 Firmware Version Displays Firmware Version for SC, SC Boot, Panel, etc.
Downloaded From ManualsPrinter.com Manuals 
						

							72
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4.2.3. Fax Service Mode 1 (Function Parameter Setting)
Use the following procedure to change the function parameters.
Enter the desired code number and press “START” key.
↓
If you wish to select another code number, scroll the menu with the “V”, ”/\” arrow keys.
↓
Select the desired function code and press the START key.
↓
When the “CLEAR” key is pressed, the selected code input will not be accepted.
↓
Press “STOP” key, then press “FUNCTION” and “CLEAR” keys sequentially to exit the service mode.
Function Parameter Table
No. Parameter Selections Function
000 Monitor/Tel Dial 1 = Monitor
2 = Tel/DialSelects whether the machine starts to TX 
automatically during On-Hook dialing.
Monitor: Start to TX after pressing START
TEL/DIAL: Start to TX automatically
001 Alarm Status 1 = Off
2 = Timer
3 = ConstantSelects the No Paper or No Toner alarm status.
OFF: Alarm is disabled.
Timer: Alarm will shut off after 6 seconds.
Constant: Alarm will not stop until STOP is 
pressed or the error is cleared/
corrected.
002 Stop Comm. 
JRNL1 = Off
2 = OnSelects whether the machine prompts to print the   
COMM. Journal when the printout condition is set to  
INC and STOP is pressed during communication.
003 Continuous Poll 1 = Off
2 = Stn (Tx only)
3 = Hub (Rx only)Selects whether the Continuous Polling feature is 
enabled.
Stn: Place the document(s) on the ADF, then 
press the assigned One-Touch Key to store 
or add the documents into a polled file. 
(See Note 1)
Hub: When the polling command is initiated, the 
machine will continuously poll originals from 
the remote stations until it is interrupted by 
pressing STOP.
004 Numeric ID Set 1 = Off (will not accept)
2 = On (accepts)Selects whether the machine accepts and allows to 
set or change the Numeric ID.
Downloaded From ManualsPrinter.com Manuals 
						

							73
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
005Destination Code
(UF-7100/8100 
only)000 : Austria
001 : U.K.
002 : Canada
003 : Denmark
004 : Taiwan
005 : Finland
006 : Germany
007 : Netherlands
008 : Italy
009 : Spanish
010 : Hong Kong
011 : Australia
012 : Switzerland
013 : Norway
015 : Portuguese
016 : Ireland
017 : Belgium
018 : Sweden
019 : Turkey
020 : U.S.A.
021 : France
022 : New Zealand
025 : Japan
029 : Poland
030 : Czech
031 : Russia
032 : Greece
033 : Hungary
034 : Indonesia
035 : South Korea
038 : Malaysia
039 : China
045 : Thailand
048 : South Africa
049 : Singapore
050 : Universal
051 : East Euro
999 : InitializeSpecified destinations only.
006 ID Display 1 = Number (Numeric ID)
2 = Chara (Character ID)Selects the priority of displaying the ID.
007 JRNL Column 1 = Station
2 = RCV’D IDSelects the contents of the ID to display on the 
Journal.
008 Monitor 1 = Off
2 = OnSelects whether the Monitor is ON/OFF for 
monitoring fax signals.
(FOR SERVICE USE ONLY)
009 DC Loop 1 = Off (Normal)
2 = On (Off Hook)Selects a false Off Hook state for back to back  
communication test.
010 TX Level 00 = 0 dBm
~
15 = -15 dBmSelects the TX signal output level, 0 to -15 dBm in 1 
dBm steps. Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							74
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
011 RX Level 1 = -43 dBm
2 = -38 dBm
3 = -33 dBm
4 = -48 dBmSelects the receiving sensitivity of -33/-38/-43/-48 
dBm.
012 DTMF Level 00 = 0 dBm
~
15 = -15 dBmSelects the DTMF output level, 0 to -15 dBm in 1 
dBm steps.
013 G3 RX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dBSelects the cable equalizer for G3 reception mode, 
0dB, 4dB, 8dB or 12dB.
014 G3 TX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dBSelects the cable equalizer for G3 transmission 
mode, 0dB, 4dB, 8dB or 12dB.
015 ~ 
016Not Used
017 TX Start 2400 bps
4800 bps
7200 bps
9600 bps
TC7200
TC9600
12000 bps
14400 bpsSelects the transmission modem start speed, 
14400/12000/TC9600/TC7200/9600/7200/4800/
2400 bps.
(Press “V” or “/ “ to select the symbol rate.)
Note:
This parameter is applicable only when 
communicating with regular G3 machines. When 
communicating with Super G3 (V.34) machines, 
use Parameter No. 32.
018 RX Start 2400 bps
4800 bps
7200 bps
9600 bps
TC7200
TC9600
12000 bps
14400 bpsSelects the reception modem start speed, 14400/
12000/TC9600/TC7200/9600/7200/4800/2400 bps.
(Press “V” or “/ “ to select the symbol rate.)
Note:
This parameter is applicable only when 
communicating with regular G3 machines. When 
communicating with Super G3 (V.34) machines, 
use Parameter No. 33.
019 ITU-T V.34 1 = Off
2 = On
3 = SelectSelects whether the ITU-T V.34 is Off, On or Select.
Select: Select whether the ITU-T V.34 is Off or On, 
when entering Phone Book Dialing 
Numbers or Manual Number Dialing.
020 ITU-T ECM 1 = Off (Invalid)
2 = On (Valid)Select the ECM mode.
021 EP Tone 1 = Off (without EP Tone)
2 = On (with EP Tone)Selects whether to add the echo protect tone on 
V.29 mode.
(Used when Echo Suppression is disabled.)
On: Add
Off: Do not add
022 Signal Interval 1 = 100 ms
2 = 200 ms
3 = 500 msSelects the time interval between the receiving 
signal and the transmitting signal.
023 TCF Check 1 = Normal (Short)
2 = LongSelects the TCF check interval Long/Short
024 CED Frequency 1 = 1080 Hz (non ITU-T)
2 = 2100 HzSelects the CED frequency 2100/1080 Hz Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							75
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
025 COMM. Start-Up 1 = First
2 = SecondSelects the communication start-up condition (XMT 
and Polling).
(Used when Echo Suppression is disabled.)
026 Non-Standard 1 = Off (Invalid)
2 = On (Valid)Selects own mode (Panafax mode).
027 Short Protocol B 1 = Off (Invalid)
2 = On (Valid)Selects the short protocol mode.
028 Short Protocol D 1 = Off (Invalid)
2 = On (Valid)Selects the short protocol mode. When activated, it 
allows the machine to automatically store the 
modem speed for each Auto Dial Number.
029 Remote 
Diagnostics1 = Off (will not accept)
2 = On (accepts)Selects whether the machine accepts Remote 
Diagnostics from the service station.
030 CED & 300 bps 1 = 75 ms
2 = 1 secSelects the pause interval between the CED and 
the 300 bps signal.  
(Used when Echo Suppression is disabled.)
031 RTC = EOL x 12 1 = Off (EOLx6)
2 = On (EOLx12)Selects the RTC signal, EOLx6 or EOLx12.
032 V34 TX Start 2400-33600bps Selects the transmission modem start speed for 
V.34 communication, 33600-2400 bps.
(Press “V” or “/ “ to select the symbol rate.)
033 V34 RX Start 2400-33600bps Selects the receiving modem start speed for V.34 
communication, 33600-2400 bps.
(Press “V” or “/ “ to select the symbol rate.)
034 V34  TX  SR 2400-3429sr Selects the transmission symbol rate for V.34, 3429/ 
3200/3000/2800/2400 sr.
(Press “V” or “/ “ to select the symbol rate.)
035 V34 RX SR 2400-3429sr Selects receiving symbol rate for V.34, 3429/3200/
3000/2800/2400 sr.
(Press “V” or “/ “ to select the symbol rate.)
036 Not Used
037 Protocol Display 1 = Off (not displayed)
2 = On (displayed)Selects whether to display the modem speed  
during communication. 
(Press the Job Status Key to display)
038 Not Used
039 Flash Time 5 = 50 ms
~
100 = 1000 msSelects the pause interval before activating the 
Flash key.
040 Flash Time 
(PSTN)5 = 50 ms
~
100 = 1000 msSelects the pause interval before activating the 
Flash key.
(For Germany, Austria and Czech)
041 Pause Time 1 = 1 sec.
~
10 = 10 sec.Selects the pause interval from 1 sec. ~ 10 sec.  for 
dialing through a switchboard or for international 
calls.
042 Not Used
043 Redial Interval 0 = no waiting
~
15 = 15 minutesSelects the redial interval from 0 to 15 minutes in 1 
minute steps. Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							76
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
044 Redial Count 0 = no redial
~
15 = 15 times
0 ~ 9 (For Australia Only)Selects the redial count from 0 to 15 times in 1 step 
intervals.
Note:
In order to comply with the TBR21 requirement 
for the EC destinations, do not select 15 times.
045 Ring Detect 
Count1 = 1 ring
~
9 = 9 ringsSelects the ring detection count from 1 to 9 rings in 
1 ring step intervals.
046 On-Hook Time 0 = 0 sec.
~
90 = 90 sec.Selects the on-hook time between sequential  
communication calls in 1 second step intervals.
047 Response Wait 
Interval1 = 1 sec.
~
90 = 90 sec.
20 ~ 150 sec. 
(For France Only)Selects the waiting interval for the response after 
completing the dialing.
048~ 
049Not Used
050 Ring Detect Mode 1 = Normal
2 = RoughSelects the quality of ringer detection. Use if the line 
signal is out of regulation, set to Rough so that the 
unit may detect the ringing signals.
051 Not Used
052 Pulse Rate 1 = 10 pps
2 = 20 ppsSelects the dial pulse rate 10/20 pps.
053~ 
054Not Used
055 Busy Tone Check 1 = Off
2 = OnSelects whether to detect the Busy Tone.
056 Dial Tone Check
(Except for USA 
and Canada)1 = Off
2 = OnSelects whether to detect Dial Tone before dialing 
the telephone number.
057 DC Loop Check
(Except for USA 
and Canada)1 = Off
2 = OnSelects whether the unit checks the DC Loop during 
communication.
058 Comm. JRNL + 
Image1 = Off (without image)
2 = On (with image)Selects whether the machine prints the COMM. 
Journal with image.
059 Not Used
060 Version Indicates the Host software 
version.
061 TX/RX/PRT/CPY TX:****** PRT:******
RX:****** CPY:******Displays the transmitted, received, total printed and 
copied document count.
062 Print Counter 1 = Off
2 = OnSelects whether to print in the Fax Parameter List, 
the counter information that is displayed in the 
Function Parameter No. 61.
063~ 
067Not UsedFunction Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							77
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
068 NYSE Fax 
Forward
(USA and Canada 
Only)1 = Off
2 = OnSelects whether the machine will forward the 
incoming and outgoing faxes to a specified station.
Note:
Once this parameter is activated, Fax 
Forwarding via Fax Parameter 054 is 
automatically disabled, an Access Code of 
0000 is automatically assigned and Fax 
Parameter 038 has a new setting added called 
NYSE.
069 NYSE Local Print
(USA and Canada 
Only)1 = Inc
2 = On (Always)Selects the printing condition for the incoming faxes 
after FAX Forwarding.
INC.: Prints only if FAX Forwarding fails.
ON: Always prints.
070 Line Error 128 lines
256 lines
512 lines
1024 line
2048 lines
Off
(will not disconnect line)1. Selects the line disconnect condition during 
reception. If the number of line errors exceed this 
setting, the unit will disconnect the line.
Press “V” or “/ “ to select the symbol rate.
2. Selects the transmit condition of RTP/PIP or 
RTN/PIN. 
(Available if No.73 Error Detect is set to LINES) 
(See Note 1)
071 Total Error 1 = 5%
2 = 10%
3 = 15%
4 = 20%Selects the transmit condition of RTP/PIP or RTN/
PIN.
(Available if No.73 Error Detect is set to RATE.)
(See Note 2)
072 Continuous Error 1 = Off (unlimited)
2 = 3 lines/STD
3 = 6 lines/STD
4 = 12 lines/STDSelects the continuous total error criteria of Off/3/6 
or 12 lines in Standard mode.   If continuous total 
error exceeds this setting, the unit will transmit 
RTN/PIN. 
(Available if No.73 Error Detect is set to RATE.)
073 Error Detect 1 = Lines
2 = RateSelects the error detect condition Lines/Rate.
074 RTN Receive 1 = Disconnect
2 = ContinueSelects whether to disconnect the phone line or 
continue when RTN is received.
075 Coding 1 = MH (MH only)
2 = MR (MH or MR)
3 = MMR
      (MH or MR or MMR)
4 = JBIGSelects the coding scheme.
076 Batch TX
(USA and Canada 
Only)1 = Off
2 = OnSelects whether the batch transmission is available.
077 RX JAM Length 1 = Off (unlimited)
2 = 2 mSelects the maximum length of a received 
document that can be printed.
078~ 
079Not Used
080 Doc Top Feed -99
~
+99Adjusts the distance between the scanning sensor 
ON position and the scanning start position.
081 Doc End Feed -90
~
+127Adjusts the distance between the scanning sensor 
OFF position and the scanning end position. Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							78
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
082 JAM Length 1 = 1 m
2 = 2 mSelects the maximum length of the original that can 
be scanned.
083 Not Used
084 Line As No Paper 1 = Ring (ring)
2 = Busy (keep line busy)Selects whether to ring or send a busy tone to the 
remote station when the recording paper runs out or 
the unit cannot receive because of any trouble.
085~
086Not Used
087 Darker Level 0 = Lightest Contrast
~
15 = Darkest ContrastSelects the contrast level.
0←             →15
Lightest← →Darkest 088 Normal Level
089 Lighter Level
090~ 
091Not Used
092 Smoothing 1 = Off
2 = OnSelects whether the smoothing function is available.
093 ~ 
094Not Used
095 Reduction Ratio (70-100) Selects Print Reduction Ratio(%).
096 ~ 
109Not Used
110 MAC Address Indicates the MAC Address.
111 Not Used
112 Insert EMAIL TXT 1 = Off
2 = OnSelects whether the Text Template (email message) 
is programmable and added on all email sent in the 
message body above the top line of text. (Up to 40 
characters Programmed in the User Parameters.)
Note:
After enabling this feature, aside from entering 
the text in the User Parameters, it also has to be 
activated in each Auto Dial Number before it will 
take effect. It does not work for Direct Dialed 
Numbers.
113 ~ 
114 Not Used
115 Time Zone 1 = Scroll
2 = DirectSelects the setting method for Time Zone.
Scroll: Allows using Scroll Keys to scroll 
through the Time Zone Table.
Direct: Allows you to input the Time Zone 
directly, (*) key to be used as a switch 
between +/-.
116 Overwrite 
Warning1 = Yes
2 = NoSelects whether the Overwrite Warning is included 
on the Internet FAX Result Receipt when 
programming the Auto Dialer via email.
11 7 ~
121Not Used
122 LDAP 1 = Off
2 = OnSelects whether to use the LDAP Server. Special 
characters used in the LDAP, may not be 
recognized and display incorrectly. Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							79
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
Note 1: Continuous Polling (Station Mode)
This feature allows you to Store or Add documents into a Polled file in memory. 
To enable the Continuous Polling feature set the Function Parameter No. 003 to 2:STN 
(Station).
Depending on the setting of the User Parameter (Facsimile) No. 119: QWERTY KEYBOAD, 
one of the following operations is available:.
1. One-Touch
The upper 40 (40↑) Key is reserved for Store 4 Polling function, and cannot be changed.
To prepare document(s) to be polled, simply place the document(s) on the ADF, then press the 
- (40) Key on the Keyboard (40↑ = LOWER Indicator turned OFF) to Store or Add document(s) 
into a Polled file.
2.Quick Name Search
Press S (13) Key to search the Store 4 Polling name instead.
To prepare document(s) to be polled, simply place the document(s) on the ADF and press the 
S (13) Key to search for Store 4 Polling, then press START Key to Store or Add 
document(s) into a Polled file.
(Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will 
not be accepted.)
Note 2: Function Parameter No. 070 (Line Error)-Transmit condition of RTP/PIP or RTN/PIN
Note 3: Function Parameter No. 071 (Total Error)-Transmit condition of RTP/PIP or RTN/PIN 123 One Ring Sound
(USA and Canada 
Only)1 = Off
2 = OnWhen Function Parameter No. 45 Ring Detect 
Count is set to 1 Ring, and this parameter is 
enabled (On), the machine will only ring once out 
loud, answering on the second ring count.
124 ~ 
199Not Used
200 ~ 
299-
See Note 5
SignalSetting
1:128 2:256 3:512 4:1024 5:2048 6:Off
MCF/PIP 0-31 0-63 0-127 0-255 0-511 Always
RTP/PIP 32-63 64-127 128-255 256-511 512-1023 -
RTN/PIN 64-127 128-255 256-511 512-1023 1024-2047 -
SignalSetting
1:5% 2:10% 3:15% 4:20%
MCF/PIP 0-2 0-4 0-7 0-9
RTP/PIP 3-4 5-9 8-14 10-19
RTN/PIN 5- 10- 15- 20-Function Parameter Table
No. Parameter Selections Function
Downloaded From ManualsPrinter.com Manuals 
						

							80
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
Note 4: The default setting of parameters depends on the country’s specifications or regulations. Print the 
Function Parameter List to confirm the default settings.
Note 5: 200 Series Function Parameters Only appear when the G3 Communications Port Kit is installed 
and follow the same numbering order.
Downloaded From ManualsPrinter.com Manuals