Panasonic Projector Pt Lz370u Operating Instructions

[PICTURE] menu
ENGLISH - 51
Settings
▶■To adjust the waveform
Project the brightness adjustment signal of a 
commercial test disk (0% (0
  IRE or 7.5   IRE) - 100% 
(100
  IRE)) and perform adjustment.
$GMXVWWR
$GMXVWWR
6LJQDOOXPLQDQFH OHYHO
6LJQDOOXPLQDQFH
OHYHO
,PDJH
GLVSOD\DEOH
DUHD
,PDJH
GLVSOD\DEOH
DUHD
$GMXVWWR
$GMXVWWR 6FUHHQ
SRVLWLRQ
6FUHHQ
SRVLWLRQ
:LWKFRPSXWHULQSXWH[FHSWPRYLH
EDVHGVLJQDORU>+0,6,*1$/
/(9(/@>@
While the waveform monitor is...

[PICTURE] menu
52 - ENGLISH
Settings
4) Adjust [FULL SCAN(B)]/[SINGLE LINE 
SCAN(B)].
▶z Select the [PICTURE] menu 
→ [ADV ANCED 
MENU] and press  ◀▶ to adjust [BRIGHTNESS 
B] and then [CONTRAST B].
[BRIGHTNESS B]
Adjusts the black level of the 
display signal to 0% (0   IRE or 
7.5
  IRE).
 zSetting range
-16 to +16
[CONTRAST B] Adjusts the white level of the 
display signal to 100% (100 IRE).
 z
Setting range
-32 to +32
▶■ To set [MONITOR POSITION]
You can set the display position of the input waveform...

[PICTURE] menu
ENGLISH - 53
Settings
 z[AUTO ADJUST] adjusts based on the 0% and 
100% standard signal within the screen. Correct 
adjustment cannot be performed if standard 
signals are not displayed on the screen because of 
overscan etc., or if a signal that is less than 0% or 
greater than 100% is displayed on the screen.
[ADVANCED MENU]
You can perform more detailed adjustment in video 
images.
1) Press  ▲▼ to select [ADV
ANCED 
MENU].
2)
 
Press the  button.
▶z The  [ADVANCED MENU]
 screen is...

[PICTURE] menu
54 - ENGLISH
Settings
[DAYLIGHT VIEW]
You can correct the image to the optimal vividness 
even if it is projected under a bright light.
1) Press ▲▼ to select [DA
YLIGHT VIEW].
2)  
Press  ◀▶ or press the  
button.
▶z The  [DAYLIGHT VIEW] individual adjustment 
screen is displayed.
3) Press  ◀▶ to switch [DAYLIGHT VIEW].
▶z
The setting will change as follows each time 
you press the button.
[AUTO][ON][OFF]
[AUTO] Enables auto correction of 
[DAYLIGHT VIEW]. The color 
sensor detects the...

[PICTURE] menu
ENGLISH - 55
Settings
[TV-SYSTEM]
▶zOnly when the / terminal is selected
The projector will automatically detect the input signal, 
but if you input an unstable signal, you can set the 
color system manually. Set the color system that 
matches the input mode.
1) Press 
▲▼ to select [TV
-SYSTEM].
2)  
Press  ◀▶ or press the  
button.
▶z The  [TV-SYSTEM] screen is displayed.
3) Press 
◀▶ to select the color system.
▶z
The setting will change as follows each time 
you press the button....

[POSITION] menu
56 - ENGLISH
Settings
Select [POSITION] from the main menu, and 
select the item from the sub-menu.
Refer to “Navigating through the menu” 
(
 page 44) for the operation of the menu 
screen.
 z After selecting the item, press 
▲▼◀▶ to set.
[KEYSTONE]
You can correct the trapezoidal distortion that occurs 
when the projector is installed tilted or when the 
screen is tilted.
1) Press 
▲▼ to select [KEYST
ONE].
2)  
Press  ◀▶ or press the  
button.
▶z The  [KEYSTONE] individual adjustment...

[POSITION] menu
ENGLISH - 57
Settings
[DOT CLOCK]
▶zOnly for computer (RGB) signal input
Use this function to adjust and minimize the effect 
of interference caused by projection of patterns 
consisting of vertical stripes.
The projection of the following striped pattern may 
cause cyclic patterns (noise). Adjust so that the 
amount of interference is at a minimum.
1) Press 
▲▼ to select [DOT CLOCK].
2)  
Press  ◀▶ or press the  
button.
▶z The  [DOT CLOCK] individual adjustment 
screen is displayed.
3)...

[POSITION] menu
58 - ENGLISH
Settings
[OVER SCAN]
Use the following steps to make adjustments when 
text and images on the periphery of the projected 
image are not properly displayed.
1) Press ▲▼ to select [OVER SCAN].
2)  
Press  ◀▶ or press the  
button.
▶z The  [OVER SCAN] individual adjustment 
screen is displayed.
3) Press  ◀▶ to adjust the level.
▶z
The adjustment values are 0 to +10.
Note
 z This item is not available for still image computer 
(RGB) signals.
[ASPECT]
You can switch the aspect...

[POSITION] menu
ENGLISH - 59
Settings
▶■For component (YCBCR/YPBPR) 
signal/movie-based computer 
(RGB) signal input
▶z For 1 125 (1080)/60i, 1125 (1080)/50i, 
1125 (1080)/60p, 1125 (1080)/50p, 1125 
(1080)/24p input
[NORMAL][S16:9]
▶z For 750 (720)/60p, 750 (720)/50p input
[NORMAL][S16:9][NATIVE]
▶zFor 525i (480i) (YCBCR) input
[AUTO][NORMAL][H FIT]
[NATIVE][FULL]
▶zFor 525i (480i) (RGB), 625i (576i), 525p 
(480p), 625p (576p) input
[NORMAL][H FIT]
[NATIVE][FULL]
Attention
 z If a 4:3 aspect video is...

[POSITION] menu
60 - ENGLISH
Settings
Aspect ratioScreen
[FULL]
The image is projected 
using all the panel 
(screen) pixels. The 
input signals are 
converted to the 
aspect ratio of the 
panel (screen). Input signal
Projection screen
[NATIVE]
The image is 
projected without size 
adjustment, keeping 
the resolution of the 
input signals. Input signal
Projection screen
[H FIT]
While the aspect ratio 
is kept fixed, The 
image is projected 
using all the panel 
pixels horizontally, and 
the vertical...