Panasonic Projector Pt Lz370u Operating Instructions

About your projector 
ENGLISH - 21
Preparation
Remote control
(15)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9) (10)
(11)
(12)
(13)
(14)
(16)(1) Remote control indicator Flashes by pressing any buttons.
(2) Power 
 button
Sets the projector to the standby mode when the  switch on the 
projector is set to . Starts projection when the projector power is of f and in the 
standby mode.
(3) Input selection (, , , and ) buttons
Switches the input signal to project. (
 page 42)
Used to set the ID number of the remote...

About your projector 
22 - ENGLISH
Preparation
Projector body
Attention
 zKeep your hands and other objects away from the 
air exhaust port.
–

▶
Keep your hands and face away
 .
–
▶
Do not insert your fingers.
–

▶
Keep heat-sensitive articles away
 .
Heated air from the air exhaust port can cause burns, 
injury, or deformations.
(1) Power indicator 
Displays the status of the power.
(2) Lamp indicator  Displays the status of the lamp.
(3) Temperature indicator  Displays the status of the internal...

About your projector 
ENGLISH - 23
Preparation
▶■Control panel
(1)
(2) (3)
(4)
(1) Power  button
Sets the projector to the standby mode when the  switch on the projector is set to . Starts 
projection when the projector power is off and in the 
standby mode.
(2)  button Displays the main menu. (3)  button
Switches the input signal to project. (
 page 42)
(4) ▲▼◀▶  buttons/ button/ button
Used to operate the menu screen.
Also used to enter the password for [SECURITY] or to 
enter characters.
▶■...

Using Remote control
24 - ENGLISH
Preparation
Using Remote control
Inserting and removing the batteries
1) Open the cover.
(i)
(ii)
2) Insert the batteries and close the cover 
(insert the 
 side first).
▶zWhen removing the batteries, perform the steps 
in the reverse order
.
Setting Remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each 
projector individually using single remote control, if a unique ID number is assigned to...

Setting up
ENGLISH - 25
Getting Started
Setting up
Projection method
You can use the projector with any of the following four projection methods. Select the appropriate method 
depending on the environment.
▶■Setting on a desk/floor and 
projecting forward▶■Mounting on the ceiling and 
projecting forward
Menu item*1Method
[PROJECTION  METHOD] [FRONT/DESK]Menu item*1Method
[PROJECTION  METHOD] [FRONT/CEILING]
▶■
Mounting on the ceiling and 
projecting from rear
(Using the translucent screen)
▶■Setting on...

Setting up
26 - ENGLISH
Getting Started
Screen size and throw distance
Install the projector referring to the following figures and tables describing projection distances. Image size and 
image position can be adjusted in accordance with the screen size and screen position.
Projection screenScreen Screen
L (LW/LT)*1Projection distance (m)
SH Image height (m)
SW Image width (m)
H Distance from the center of lens to the image lower end (m)
SD Image diagonal size (m)
*1: LW: Minimum projection distance
LT:...

Setting up
ENGLISH - 27
Getting Started
▶zWhen the screen aspect ratio is 4:3
(All measurements below are approximate and may differ slightly from the actual measurements.)
(unit: m)
Image diagonal size (SD)Projection distance (L)
Distance from the center of 
lens to the image lower end (H)
Minimum projection 
distance (LW) Maximum projection 
distance (LT)
1.02 (40") 1.38 (4' 6") 2.82 (9' 3")
-0.02 - 0.63
1.27 (50") 1.74 (5' 9") 3.53 (11' 7")
-0.02 - 0.78
1.52...

Setting up
28 - ENGLISH
Getting Started
Adjusting adjustable feet
In order to make the projection screen rectangle, place the projector on a flat surface with its front surface parallel 
to the screen. If the screen is tilted lower, extend the adjustable feet and adjust the angle to make a rectangle 
screen. If the projector is tilted horizontally, also use the adjustable feet and adjust the angle to keep the projector 
flat. The adjustable feet can be extended by turning it as shown in the figure, and...

Setting up
ENGLISH - 29
Getting Started
3) Adjust projection using the lens shift lever.
▶zWhen adjusting the horizontal position, move the lens shift lever horizontally
.
Up to approx. 26% \nof the 
projection \fcreenUp to approx. 26% \nof the 
projection \fcreen
Screen
Move the \ben\f \fhift \be\nver 
in direction A Move the \ben\f \fhift \be\nver 
in direction B
▶z
When adjusting the vertical position, move the lens shift lever vertically
.
Move the lens shif\Ut 
lever in direction\U D
Move the lens...

Setting up
30 - ENGLISH
Getting Started
▶■Projector location range
The setting position can be adjusted within the following range.
Refer to “Screen size and throw distance” (
 page 26) for the projection screen height (SH) and width (SW).
▶z
Projector setting range when the screen position is fixed
Projector
Projector setting \S
range (center of l\Sens)
Center of lens
Screen
\fertical center of \Sscreen