Panasonic Projector Pt Lb30ntu Operating Instructions

							ENGLISH-41
Adjustments and settings
Press the For Gbutton on the
projector or remote control unit to
select an item, and then press the I
or Hbutton to change the setting.
For items with bar scales, press the
ENTER button or the Ior Hbutton
to display the adjustment screen,
and then press the Ior Hbutton
to make the adjustment.
When an RGB/YP
BPRsignal is
being input
When an S-VIDEO/VIDEO signal is
being input
POSITION
Moves the picture position.
Press the ENTER button to display the
“POSITION” screen.
Press the Ior Hbutton to move the
picture horizontally.
Press the For Gbutton to move the
picture vertically.
DOT CLOCK
(RGB only)
Periodic striped pattern interference
(noise) may occur when a striped
pattern such as the one below is
projected. If this happens, press the
Ior Hbutton to adjust so that any
such noise is minimised.
CLOCK PHASE
(RGB/YPBPRonly)
Adjust the “DOT CLOCK” setting
first before carrying out this
adjustment. Press the Ior H
button to adjust so that the noise
level is least noticeable.
Adjusting the position
       POSITION
POSITION
DOT CLOCK     32
CLOCK PHASE   16
ASPECT          4:3
RESIZING        ON
FRAME LOCK      OFF
STANDARD
  SELECT  ENTER  RETRN
       POSITION
POSITION    
ASPECT          4:3
RESIZING        ON  
STANDARD        
  SELECT  ENTER  RETRN
When an RGB signal is being
input, press the AUTO SETUP
button first to initiate automatic
positioning. If the optimum setting
is not obtained when “AUTO
SETUP” is carried out, adjust by
the following procedure.
NOTE:
BIf signals with a dot clock
frequency of 100 MHz or
higher are being input,
interference may not be
completely eliminated when
the “DOT CLOCK” and
“CLOCK PHASE” adjustments
are carried out.
POSITION   H  64
           V  32 
						

							42-ENGLISH
S4:3
The size of the input signal is
compressed to 75% and projected.
(This is useful for projecting a
picture with a 4:3 aspect ratio onto a
16:9 screen.)
AUTO
(S-VIDEO only)
When an S1 video signal is being
input, the aspect ratio is changed
automatically to project a 16:9
picture.
4:3
The input signal is projected without
change.
16:9
The picture is compressed to a ratio
of 16:9 and projected.
ASPECT         AUTO                                [                4:3                                [               16:9                                [               S4:3
S1 video signals
BS1 video signals are a type of
video signal with an aspect ratio
of 16:9 which include a detector
signal. This detector signal is
output by some sources such as
wide-vision video decks. 
BWhen “ASPECT” is set to
“AUTO”, the projector recognizes
the detector signal and
automatically switches the aspect
ratio to 16:9. When a horizontally
squeezed signal is
being input.When a 4:3 signal
is being input.
[[
When using the 16:9 screen
ASPECT
(S-VIDEO/VIDEO/480i, 576i, 480p
and 576p YP
BPRonly) 
						

							RESIZING
This should normally be set to “ON”.
(This setting is only for signals
which have lower resolutions than
the LCD panels. Refer to page 62
for details.)
ON
The pixel resolution of the input
signal is converted to the same
resolution as the LCD panels before
being projected. 
This may sometimes cause
problems with the quality of the
picture.
OFF
The input signal is projected at its
original resolution, with no pixel
conversion. The projected picture
will be smaller than normal, so
adjust the zoom setting or move the
projector forwards or backwards to
adjust the picture size if necessary.
If set to “OFF”, some features, such
as “D.ZOOM” (digital zoom),
“KEYSTONE” or “INDEX WINDOW”
will not function.
FRAME LOCK
If the picture’s condition is bad while
a RGB moving picture is projected,
set “FRAME LOCK” to “ON”. Refer
to page 62 for compatible RGB
signals.
NOTE:
BIf using this projector in places
such as cafes or hotels to
display programs for a
commercial purpose or for
public presentation, note that if
the aspect ratio (16:9)
selection function is used to
change the aspect ratio of the
screen picture, you may be
infringing the rights of the
original copyright owner for
that program under copyright
protection laws.
BIf a 4:3 picture is projected
onto a 16:9 screen, distortion
may occur around the edges of
the picture so that part of the
picture is no longer visible.
Programs which have 4:3
aspect ratios should be viewed
in 4:3 mode to give proper
consideration to the aims and
intentions of the original
program’s creator.
ENGLISH-43
Adjustments and settings 
						

							44-ENGLISH
Changing the display language
Press the For Gbutton on the projector or remote control unit to select a
language, then press the ENTER button to accept the setting.
Indicates the language which is
currently set.
   LANGUAGE    ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
NORSK
DANSK
POLSKI
CESTINA
MAGYAR
yyyyyyyyyyyyyyyyyyyyÝ  SELECT  ENTER  RETRN
   LANGUAGE    ENGLISH
yyyyyyyyyyyyyyyyyyyyÛ
ENGLISH¤
ÔŠ 
  SELECT  ENTER  RETRN 
						

							ENGLISH-45
Adjustments and settings
Option settings
Press the For Gbutton on the
projector or remote control unit to
select an item, then press the Ior
Hbutton to change the setting.
        OPTIONyyyyyyyyyyyyyyyyyyyyÛBACK COLOR     BLUE
FRONT/REAR    FRONT
DESK/CEILING   DESK
FAN CONTROL  STANDARD
LAMP POWER     HIGH
LAMP RUNTIME   10H
FUNC 1       DAYLIGHT
CONTROL KEY     ON
AUTO POW.OFF DISABLE
POWER MEMORY    ON
  SELECT  ADJ    RETRN
NOTE:
BThe setting for “TV-SYSTEM”
will also be displayed when an
S-VIDEO/VIDEO signal is being
input.
        OPTION
OSD             ON
AUTO SEARCH     ON
AUTO SIGNAL     ON
AUTO KEYSTN     ON
RGB2 SELECT   INPUT
RGB/YP
BPR      AUTO
VGA60/480p     480p
SXGA MODE      SXGA
NR              OFF
BLACKBOARD      OFF
yyyyyyyyyyyyyyyyyyyyÝ  SELECT  ADJ    RETRN
OSD
ON
The signal name is displayed in the
top-right corner of the screen when
the input signal is changed.
OFF
Use this setting when you do not want
the signal name to be displayed.
AUTO SEARCH
This should normally be set to “ON”
ON
When the power is turned on and
“AUTO SETUP” is running, the
projector detects which signals are
being input, and uses these signals
for projection. 
(If a picture is being projected, the
signal source is not automatically
changed.)
OFF
Use this setting when you do not
want the signal source to be
changed automatically when the
power is turned on and “AUTO
SETUP” is running.
AUTO SIGNAL
This should normally be set to “ON”.
ON
“AUTO SETUP” will be carried out
automatically when the input signal
is changed.
OFF
“AUTO SETUP” will not function
when the input signal is changed.
AUTO KEYSTN
This should normally be set to “ON”.
ON
During “AUTO SETUP”, the angle
of tilt of the projector is detected
and keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during “AUTO
SETUP”, such as when the screen
itself is at an angle. 
						

							46-ENGLISH
RGB2 SELECT
This setting is used to select the
function of the RGB2 IN/1 OUT
connector.
RGB/YPBPR
This should normally be set to
“AUTO”. RGB or YP
BPRis selected
automatically depending on the
synchronising signal status.
When 480i, 576i, 480p, 576p, 
1 080/60i, 1 080/50i, 720/60p and
some VGA480 signals are being
input, select “RGB” or “YP
BPR” in
accordance with the input signal.
VGA60/480p
Set to “VGA60” when 59.9Hz
VGA480 signals are being input
(refer to page 62 for details). Set to
“480p” when 480p RGB signals are
being input.
SXGA MODE
This setting is only for an SXGA
signal.
SXGA
Select this item normally.
SXGA+
When the edges of the projected
image are not visible, select this
item.
Noise Reduction (NR)
(S-VIDEO/VIDEO only)
If the signal is of such poor quality
that picture interference appears,
set “NR” to “ON”. To turn off the
“NR” feature, set to “OFF”.
BLACKBOARD 
Set to “ON” when “PICTURE
MODE” is set to “BLACK-BD”.
(Refer to page 37.)
BACK COLOR
This sets the color which is
projected onto the screen when no
signal is being input to the projector.
FRONT/REAR
This setting should be changed in
accordance with the projector
setting-up method. 
(Refer to page 18.)
FRONT
When the projector is placed in front
of a screen.
REAR
When using a translucent screen.
RGB/YPBPR      AUTO                               [                    RGB                               [
                     YPBPR
VGA60/480p     480p                                [               VGA60
BACK COLOR     BLUE                                [              BLACK
FRONT/REAR    FRONT                                [               REAR
SXGA MODE      SXGA                                [               SXGA+ 
						

							ENGLISH-47
Adjustments and settings
DESK/CEILING
This setting should be changed in
accordance with the projector 
setting-up method. 
(Refer to page 18.)
DESK
When the projector is placed on a
desk or similar.
CEILING
When the projector is suspended
from a ceiling using the ceiling
bracket (sold separately).
FAN CONTROL
Set “FAN CONTROL” to “HIGH”,
when using this projector at high
elevations (above 1 400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
luminance of the lamp is reduced,
but the projector uses less power,
and the operating noise is also
reduced. This can help to extend
the lamp’s operating life. If using the
projector in small rooms where high
luminance is not required, it is
recommended that you set the
“LAMP POWER” to “LOW”.
LAMP RUNTIME
This setting displays the usage time
for the lamp unit which is currently
being used. When replacing the
lamp unit, follow the instructions on
page 56, and reset “LAMP
RUNTIME” to “0”.
FUNC 1
This assigns a function to the
FUNC1 button of the ET-RM300
wireless remote control unit (sold
separately).
DAYLIGHT
Functions in the same way as when
“DAYLIGHTVIEW” is selected from
the “PICTURE” menu. (page 39)
KEYSTONE
Functions in the same way as when
“KEYSTONE” is selected from the
“MAIN MENU”. (page 36)
DESK/CEILING   DESK                                [             CEILING
LAMP POWER     HIGH                                [               LOW
FAN CONTROL  STANDARD                                  [               HIGH
NOTE:
B“LAMP POWER” cannot be set
when no signal is being input.
FUNC1        DAYLIGHT                                [             KEYSTONE
NOTE:
BThe lamp’s operating life varies
depending on the usage
conditions (such as the “LAMP
POWER” setting and the
number of times the power is
turned on and off).  
						

							48-ENGLISH
CONTROL KEY
To disable the buttons on the
projector, set “CONTROL KEY” to
“OFF”. A confirmation screen will
then be displayed. Select “OK” by
using Ior Hbutton. To use the
buttons on the projector, set to “ON”
by using the remote control unit. 
AUTO POW.OFF
If no signal is input to the projector
for the duration of the period you
set, the projector will return to
standby mode. The period can be
set from 15 minutes to 60 minutes
in 5 minute intervals. If you don’t
use this feature, set it to “DISABLE”. 
This feature will not function when
using the “FREEZE” function.
POWER MEMORY
This sets the projector’s start up
status for when the power cord is
connected.
ON
The projector will start from the
same status as when the power
cord was disconnected. If the power
cord was disconnected during
projection when the projector was
used the last time, projection will
start after the power cord is
connected.
OFF
The projector will be in standby
mode. 
						

							ENGLISH-49
Adjustments and settings
Setting up the security function
This projector is equipped with a security function. A password input screen
can be displayed, or a company URL can be set up and displayed at the
bottom of the projected image.
Press the For Gbutton on the
projector or remote control unit to
select “SECURITY”, then press the
ENTER button.
       MENU
KEYSTONE
PICTURE
POSITION
INDEX WINDOW
SHUTTER
VOLUME
LANGUAGE
OPTION
SECURITY
NETWORK
SELECT
  ENTER  EXIT
PASSWORD
   OK        
 RETURN
   AMEND PASSWD
NEW
CONFIRM
   OK        
 RETURN
       SECURITY
INPUT PASSWD   OFF
AMEND PASSWD 
TEXT DISPLAY   OFF
TEXT CHANGE
  SELECT  
ADJ    RETRN
INPUT PASSWD
The password input screen can be
displayed when the power is turned
on. All of the controls other than the
POWER button are disabled unless
the password is entered correctly.
ON
“INPUT PASSWD” is enabled.
OFF
“INPUT PASSWD” is disabled. The
password input screen will not be
displayed when the power is turned
on.
AMEND PASSWD
Passwords can be changed. Press
the ENTER button to display the
“AMEND PASSWD” screen.
#Set a password by pressing the
F,G,I, and Hbuttons. 
(A maximum of 8 buttons can be
set.)
$Press the ENTER button.
%Enter the password again for
confirmation.
&Press the ENTER button.
Password change will be
completed. (When you use the “SECURITY”
function for the first time)
Press the F, H, G, I, F, H, G
and Ibuttons in order, then press
the ENTER button.
(When a password change has
been made before)
Type in the changed password, then
press the ENTER button. 
						

							50-ENGLISH
TEXT DISPLAY
You can set text to be displayed at
the bottom of the projected image at
all times.
ON
“TEXT DISPLAY” is enabled.
OFF
“TEXT DISPLAY” is disabled.
TEXT CHANGE
The text which is displayed when
“TEXT DISPLAY” is set to “ON” can
be changed.
Press the ENTER button to display
the “TEXT CHANGE” screen.
#Press the F, G, Iand H
buttons to select the characters,
then press the ENTER button.
(You can enter 22 characters
continuously.)
CSelect “BS” to delete a
character.
$Press the F, G, Iand H
buttons to select “OK”, then press
the ENTER button.
CSelect “Cancel” to cancel the
change.
NOTE:
BThe entered password will
appear as   . It will not be
displayed on the screen.
BIf you enter the wrong
password, the letters
“PASSWORD” and “NEW” will
become red. Enter the correct
password again.
BSOKCancel
yyyyy5&95
$)/(&


yy !#$
yy%&()*+,-./€|}
yy0123456789:;
yy?@ABCDEFGHI—´µÎ
yy
yŠÏ¦§