Panasonic Projector PT-DZ16KU User Manual

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 91
2) Press qw to switch the item.
 fThe items will switch each time you press the button.
[BLUE] Displays the entire projection area in blue.
[BLACK] Displays the entire projection area in black.
[DEFAULT LOGO] Displays the Panasonic logo.
[USER LOGO] Displays the image registered by the user.
Note
 fTo create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[STARTUP LOGO]
Set the logo display when the...

Chapter 4 Settings — [DISPLAY OPTION] menu
92 - ENGLISH
3) Press as to select [FADE-IN] or [FADE-OUT].
4)  
Press 
 qw to switch the item.
Item Adjustment
[FADE-IN]
[FADE-OUT] [OFF]
Does not set fade-in or fade-out.
[0.5 s] 
‑  [10.0 s]Allows you to set the fade-in or fade-out time.
Select an item from [0.5 s] to [4.0 s], [5.0 s], [7.0 s], and [10.0 s]. 
[0.5 s] - [4.0 s] can be selected in increments of 0.5.
Note
 f
Press the  button on the remote control or the control panel during fade-in or fade-out...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 93
3) Press the  button two times to clear.
4)  
Press 
 as to select any horizontal line.
5)
 
Press the  button to switch the Select line to either luminance, red, green, or blue.
 f Line selection items switch each time the  is pressed only when the waveform monitor is displayed.
“Select line (luminance)” Displayed in white waveform.
“Select line (red)” Displayed in red waveform.
“Select line (green)” Displayed in green waveform.
“Select line...

Chapter 4 Settings — [DISPLAY OPTION] menu
94 - ENGLISH
2) Press the  button.
 fThe  [CUT OFF] screen is displayed.
3) Press  as to select [RED], [GREEN], or [BLUE].
4)  
Press 
 qw to switch the item.
[OFF] Disables cutoff.
[ON] Enables cutoff.
Note
 fWhen input is switched or a signal is switched, the cutof f setting returns to its original setting (off).   

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 95
[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item 
from the sub‑ menu.
Refer to “Navigating through the menu” ( x
  page   59) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when multiple projectors are used side by side to enable simultaneous 
control or individual control...

Chapter 4 Settings — [PROJECTOR SETUP] menu
96 - ENGLISH
[COOLING CONDITION]
Change the fan control depending on the direction of projection.
Set [COOLING CONDITION] according to the projection direction, but set it to [AUTO] normally. Using the projector with incorrect setting may 
shorten the life of the lamp.

30°
30° 30°
30°
[VERTICAL UP SETTING]
[FLOOR SETTING] [CEILING SETTING]
[VERTICAL DOWN SETTING] Projection direction
1) Press as to select [COOLING CONDITION].
2)  
Press the  button.
 f The...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 97
[L1/L2/L4]Lamp 1, 2, and 4 will light.
[L1/L3/L4] Lamp 1, 3, and 4 will light.
[L2/L3/L4] Lamp 2, 3, and 4 will light.
[SINGLE] One lamp will light. (The lamp with shorter runtime will automatically light.)
[DUAL] Two lamps will light. (The lamps with shorter runtime will automatically light.)
[TRIPLE] Three lamps will light. (The lamps with shorter runtime will automatically light.)
[QUAD] Four lamps will light.
3) Press the  button.
Note
 f For a...

Chapter 4 Settings — [PROJECTOR SETUP] menu
98 - ENGLISH
[SUNDAY]Switches the lamp automatically on the set day of the week.
[MONDAY]
[TUESDAY]
[WEDNESDAY] [THURSDAY] [FRIDAY]
[SATURDAY]
Note
 f The [LAMP  RELAY] function is enabled when [SINGLE], [DUAL], [TRIPLE], or [QUAD] is selected in [LAMP SELECT]. fWhen [SINGLE] or [DUAL] is selected in [LAMP
 SELECT], lamps are switched at the specified time. When [TRIPLE] is selected in [LAMP  
SELECT], lamps are switched three times every two hours after the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 99
5) Press as to select [MODE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not correct the brightness of the screen by the brightness sensor .
[AUTO] Corrects the brightness of the screen by the brightness sensor.
Automatically corrects screen brightness when lamp brightness changes.
[PC] Synchronizes nine or more projectors through a computer using the dedicated software “Multi 
Projector...

Chapter 4 Settings — [PROJECTOR SETUP] menu
100 - ENGLISH
 fIf the  button is pressed when [LINK] is set from [GROUP  A] to [GROUP D], the group name is displayed on the screens of 
projectors that have been set in the same group.
LINK GROUP A
Note
 fWhen [MODE] in [BRIGHTNESS CONTROL  SETUP] is set to [AUTO] or [PC], keep the shutter open for at least two minutes to perform the 
brightness sensor calibration after completed the [BRIGHTNESS CONTROL  SETUP] setting.
 fIf the shutter is closed within...