Panasonic Projector PT-DZ16KU User Manual

Chapter 3 Basic Operations — Projecting
ENGLISH - 51
Projecting
Check the projection lens attachment (x   page   41), external device connection (x   page   43), power cord connection (x   page   47), 
switch on the power ( x
  page   48) to start projecting. Select the video for projection, and adjust appearance of the projected image.
Selecting the input signal
Select an input signal.
1) Press the input selection (, , , , , ) buttons on the 
control panel or the remote control.
 f The image of the...

Chapter 3 Basic Operations — Projecting
52 - ENGLISH
Moving the lens to the home position
To move the lens to the home position, perform the following procedure.
1) Press the  button on the remote control while the shift adjustment screen is displayed.
 fThe  [HOME POSITION]  screen is displayed.
LENS
HOME POSITION
EXECUTE
CANCEL
ENTERMENU
2) While the [HOME POSITION] screen is displayed (for approximately five seconds), press the  
button.
 f[PROGRESS] is displayed in the  [HOME POSITION] screen, and...

Chapter 3 Basic Operations — Projecting
ENGLISH - 53
Adjusting the lens mounter when the focus is unbalanced
Focus balance
Relationship between the tilt of the lens and the screen focus surface
When the projection lens is tilted in contrast with the image forming surface, tilting the front side (screen side) of the projection lens downwards 
(in the direction of the dotted arrow line), the upper side of the screen focus surface will tilt inwards and the lower side will tilt outwards as 
shown in the...

Chapter 3 Basic Operations — Projecting
54 - ENGLISH
Adjustment procedure
 rRelationship between the adjustment location and adjustment screws
(b) (c)
(b)+(c)
(a)
Adjustment location:
Location where the just focus point of the screen is in the 
inner side of the screen
When the just focus point of 
the screen in V up (top in the 
vertical direction) is in the inner 
side of the screen When the just focus point of the 
screen in V bottom (bottom in 
the vertical direction) is in the 
inner side of the...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 55
Operating with the remote control
Using the shutter function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the image 
temporarily.
 button
1) Press the  button.
 f The image disappears.
 fThis operation can be also performed using the  button on the control panel.
2) Press the  button again.
 fThe image is displayed.
Note
 fThe power indicator...

Chapter 3 Basic Operations — Operating with the remote control
56 - ENGLISH
Switching the input signal
The input for projection can be switched.
 button
1) Press the input selection (, , , , , ) buttons.
 fThis operation can be also performed using the buttons on the control panel.
 Switches the input to RGB1.
 Switches the input to RGB2.
 Switches the input to DVI
- D.
 Switches the input to VIDEO.
 Switches the input to HDMI.
 Switches the input to SDI.
Using the Status function
You can display the...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 57
 fIf an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even 
when [COMPLETE] appears. In this case, adjust the settings in the [ADV ANCED MENU] menu →
 [INPUT RESOLUTION] (x
  page   78), 
[POSITION]  → [CLOCK PHASE] (x
  page   74), and [SHIFT] (x   page   72).
 fAdjust special signals according to the [DISPLA

Y OPTION] menu → [AUTO SETUP] ( x
  page...

58 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using the on-screen menu.   

Chapter 4 Settings — Menu navigation
ENGLISH - 59
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe  [MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
PROJECTOR SETUP DISPLAY OPTION
P IN P
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
TEST PATTERN
ENTER
2) Press  as to select an...

Chapter 4 Settings — Menu navigation
60 - ENGLISH
4) Press as to select a sub ‑ menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw .
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown below .
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu. fDepending on the signals to be input to the projector
, some items or...